Titan Fitness 4FPWR User manual

Owner’s
Manual
This Product is Distributed Exclusively by
Titan Distributors Inc
141 Eastley St. Ste. 113 Collierville, TN 38017
Customer Service
800 - 605 - 8241
www.tan.tness
41” FOLDING POWER RACK

2
BOX 2
BOX 1
FOLDING POWER RACK
PARTS LIST
To begin, match up
all the parts with
the following parts
diagrams:
DIAGRAM NO. PACKAGE NO. PART NUMBER DESCRIPTION QTY
11P400181-1Upright Post 2
22P400182-2HD J-Hook 4
31&2 P400182-3Long Side Bracing + Short Hinge 2
42P400182-4Short Side Bracing + Long Hinge 2
52P400182-5Hinge Pin 4
62P400182-6Hex Bolt M16x110 8
72P400182-7Flat Washer 8
82P400182-8Spring Washer 8
92P400182-9Hex Nut 8
10 2P400182-10 Pin Lock 2
11 2P400182-11 Coer Pin 4
12 1P400181-12 Post End Cap 2
13 2P400182-13 Pull Up Bar Pins 2
14 1P400181-14 Pullup Bar 1
1
14
3
3
5
11
10
2
(8) Hex Nut M16
(8) Hex Bolt M16x110
(8) Flat Washer (8) Spring Washer
7
69
8
13
4

3
PLEASE NOTE
Two 2” x 10” stringers must be mounted into a minimum of four studs.
The vercal center of the boom stringer should be
mounted 7.25” from level ground.
The vercal center of the top stringer should be
mounted 76” from level ground.
NECESSARY HARDWARE MAY VARY ACCORDING TO YOUR MOUNTING
SURFACE. CONSULT YOUR LOCAL HARDWARE STORE FOR THE PROPER
MOUNTING HARDWARE.

4
BUILD ON A FLAT AND LEVEL SURFACE.
STEP 1
 Aach LONG SIDE BRACING + SHORT HINGE (3) to one
UPRIGHT POLE (1) using four HEX BOLTS M16x110 (6), four
FLAT WASHERS (7), four SPRING WASHERS (8), and four
HEX NUTS (9).
 Aach SHORT SIDE BRACING + LONG HINGE (4) to the other
UPRIGHT POLE (1) using the same hardware described in
the previous step.
 Slide the four HINGE PINS (5) in through the top and the
four COTTER PINS (11) through the boom.
NOTE: UHMW padding is at the boom of the UPRIGHT POLES (1).
TOP BOTTOM

5
STEP 2
 Aach PULLUP BAR (14) to the top of the UPRIGHT POLES
(1) using two PULL UP BAR PINS (13) and two PIN LOCKS
(10).

6
STEP 3
 Mount the SIDE BRACINGS + HINGES (3 & 4) to your wall
using the pictured measurements.
 NOTE: The 2 pcs of (3) should be on the same side aligned
vercally and the 2 pcs of (4) should be on the other side
aligned vercally. This will allow the rack to fold over itself.
 When mounng each SIDE BRACING + HINGES (3 & 4), the
two holes are each spaced 6.4”.
 The mounng holes on the top two SIDE BRACINGS +
HINGES (3 & 4) are 76” from level ground.
 The mounng holes on the boom two SIDE BRACINGS +
HINGES (3 & 4) are 7.25” from level ground.
 The inside holes should be should be spaced 41.5” from the
center of each hole.
TOP HOLE TO GROUND - 76”
INSIDE HOLES - 41.5”
6.4”
NOTICE
TEST FIT YOUR FOLDING
POWER RACK AT THE
PROVIDED MEASUREMENTS.
CHECK FOR CLEARANCE
WHILE SLIDING THE RACK
OPEN AND CLOSED. SEE THE
TROUBLESHOOTING CHART
ON THE NEXT PAGE FOR ANY
NECESSARY ADJUSTMENTS.

7
TROUBLESHOOTING
PROBLEM PROBABLE CAUSE SOLUTION
Rack slides right, but not
le.
Top mount is slightly to the
le of the boom mount.
Move top mount slightly
to the right.
Rack slides le, but not
right.
Top mount is slightly to the
right of the boom mount.
Move top mount slightly
to the le.
Rack is too high when
open, but not when closed.
Either wall or oor is not
level.
(wall and oor is greater
than 90°)
Add a thin spacer behind
the upper mounts.
Rack is too low when open,
but not when closing.
Either wall or oor is not
level.
(wall and oor is less than
90°)
Slightly raise all mounng
points on the wall.
Add a thin spacer behind
the lower mounts.
Rack is too high when both,
open and closed.
Rack is mounted too high. Lower all mounng points
on the wall.
Rack is too low when both,
open and closed.
Rack is mounted too low. Raise all mounng points
on the wall.
The provided
measurements are
substanally inaccurate.
The upper and lower side
bracings are not mounted in
the suggested upright holes.
Upper side bracing:
6th and 9th from the top
Lower side bracing:
2nd and 5th from the
boom

WARNING
Exercise can present a health risk. Consult a physician before beginning any exercise
program with this equipment. If you feel faint or dizzy, immediately disconnue use
of this equipment. Serious bodily injury can occur if this equipment is not assembled
and used correctly. Serious bodily injury can occur if all instrucons are not followed.
Keep others and pets away from equipment when in use. Always make sure all bolts
and nuts are securely ghtened prior to each use. Follow all safety instrucons in
this manual.
91”
50”
Features
 Steel J-Hooks
 2"x3" steel tubes
 Powder coated durable nish
 Laser cut for precise t
Specicaons
 Weight: 175 lbs
 Height: 91"
 Opening: 50"
 Depth: 41.5"
 Dimensions: (H)91" x (W)50" x (L)44.5"
 Material: Steel
TITAN FITNESS
141 Eastley St. Ste. 113 Collierville, TN 38017 [phone]
www.tan.tness E-MAIL: team@tan.tness