Marcy RS7000 User manual

Marcy Fitness www.marcyfitness.co.uk
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Pack
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
RS7000
Retain This
Manual for
Reference
01012014
OWNER'S
MANUAL
MARCY ECLIPSE RS7000
DELUXE SMITH CAGE

Marcy Fitness www.marcyfitness.co.uk
TABLE OF CONTENTS
BEFORE YOU BEGIN..................................................................………… 1
IMPORTANT SAFETY NOTICES AND WARNING LABEL PLACEMENT 2-3
SMITH CAGE HARDWARE PACK….......…............................................. 4-7
SMITH CAGE ASSEMBLY INSTRUCTIONS............................................ 8-25
EXPLODED DIAGRAM………………………………………………………. 26
SMITH CAGE PARTS LIST………..………………………………………… 27
MULTI-PURPOSE BENCH HARDWARE PACK………………………….. 28-29
MULTI-PURPOSE BENCH ASSEMBLY INSTRUCTIONS....................... 30-33
EXPLODED DIAGRAM………………………………………………………. 34
MULTI-PURPOSE BENCH PARTS LIST…………………………………… 35
WEIGHT RESISTANCE CHART……………………………………………… 36
WARRANTY............................................................................................... 37
ORDERING PARTS.................................................................................... 37
BEFORE YOU BEGIN
Thank you for selecting the MARCY Eclipse RS7000 Deluxe Smith Cage. For your safety and benefit, read
this manual carefully before using the equipment. As a distributor, we are committed to provide you complete
customer satisfaction. If you have any questions, or find there are missing or damaged parts, we guarantee
you complete satisfaction through direct assistance. To avoid unnecessary delays, please contact our
customer service department, Monday to Friday 9am – 5pm GMT + 1 hour.
E mail: [e-mail]
Supplied by
Tunturi Fitness B.V.
www.tunturi-fitness.com
E mail: [e-mail]
1

Marcy Fitness www.marcyfitness.co.uk
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
CARE AND MAINTENANCE
1. Lubricate moving parts with WD-40 or light oil periodically.
2. Inspect and tighten all parts before using the machine.
3. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
4. Maximum user’s weight: 136kgs
5. Maximum weights on the Weight Bar: 136kgs
6. Maximum weights on Leg Developer: 45kgs
7. Maximum weights on Cross-over, Lat Pull: 90kgs
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE
OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. TUNTURI FITNESS
BV ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS. 2

Marcy Fitness www.marcyfitness.co.uk
WARNING LABEL PLACEMENT
The warning labels shown here have been placed on the Rear Base, and Bench Rear Stabilizer. If the
labels are missing or illegible, please contact customer service by email: service.international@tunturi-
fitness.com for replacements. Apply the labels in the location shown.
3

Marcy Fitness www.marcyfitness.co.uk
SMITH CAGE HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the
size.

Marcy Fitness www.marcyfitness.co.uk
4

Marcy Fitness www.marcyfitness.co.uk
SMITH CAGE HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
5

Marcy Fitness www.marcyfitness.co.uk
SMITH CAGE HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
6

Marcy Fitness www.marcyfitness.co.uk
SMITH CAGE HARDWARE PACK
7

Marcy Fitness www.marcyfitness.co.uk
SMITH CAGE ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches.
NOTE: It is strongly recommended that two or more people assemble this machine to
avoid possible injury.
STEP 1 (See Diagram 1)
A.) Do not tighten Nuts and Bolts until instructed to do so.
B.) Insert a Base Frame (#5) into the Rear Left Vertical Frame (#3). Secure it with two M10 x
¾” Allen Bolts (#90) and two Ø ¾” Washers (#107).
C.) Repeat B to install the other Base Frame to Rear Right Vertical Frame (#4).
D.) Attach Rear Base Frame (#8) to Rear Left and Right Vertical Frame. Secure each end
with two M10 x 2 ½” Allen Bolts (#95), four Ø ¾” Washers (#107), and two M10 Aircraft
Nuts (#110).
E.) Repeat D to connect Rear Top Beam (#6) to Rear Left and Right Vertical Frame.
DIAGRAM 1
8

Marcy Fitness www.marcyfitness.co.uk
STEP 2 (See Diagram 2)
A.) Do not tighten the Nuts and Bolts until instructed to do so.
B.) Insert a Guide Rod (#24) into the hole on left Base Frame (#5). Secure it with one M8 x 2
3/8” Allen Bolt (#103), two Ø 5/8” Washers (#106), and one M8 Aircraft Nut (#109). Slide
the Left Lower Safety Stop Frame (#26) onto the Guide Rod, and then slide one Safety
Stop Frame (#25) onto the Guide Rod.
C.)Attach the Front Left Vertical Frame (#1) onto the left Base Frame. Secure it with two M10
x 3 1/8” Allen Bolt (#98), four Ø ¾” Washers (#107), and two M10 Aircraft Nuts (#110).
D.)Attach one Upper Side Frame (#7) to the Guide Rod, Front Left Vertical Frame, and Rear
Left Vertical Frame (#3).
E.) Secure the Upper Side Frame to Rear Left Vertical Frame from side with one M10 x 2 ½”
Carriage Bolt (#88), one Ø ¾” Washer (#107), and one M10 Aircraft Nut (#110). Secure it
from rear with one M10 x 5/8” Allen Bolt (#87) and one Ø ¾” Washer (#107).
F.) Secure the Upper Side Frame to the Guide Rod with one M10 x ¾” Allen Bolt (#90), and
one Ø ¾” Washer (#107).
G.)Secure the Upper Side Frame to the Front Left Vertical Frame with one Left Chin-up
Bracket (#49), two M10 x ¾” Allen Bolts (#90) and two Ø ¾” Washers (#107).
H.)Repeat B to G above to install the other side.
I.) Attach the Chin-up Bar (#30) to the Left and Right Chin-up Bracket (#49 & #50). Secure
each end of Chin-up Bar with two M10 x 1 5/8” Carriage Bolts (#86), two Ø ¾” Washers
(#107), and two M10 Aircraft Nuts (#110).
9

Marcy Fitness www.marcyfitness.co.uk
DIAGRAM 2
10

Marcy Fitness www.marcyfitness.co.uk
STEP 3 (See Diagram 3)
A.) Do not tighten all Nuts and Bolts until instructed to so.
B.) Attach the Middle Vertical Frame (#9) under the Rear Top Beam (#6) and onto the Rear
Base Frame (#8).
C.)Attach the Lower Pulley Frame (#16) to the Middle Vertical Frame from rear. Attach the
Foot Plate (#32) to the Middle Vertical Frame from front. Secure them together with two
M10 x 3” Carriage Bolts (#89), two Ø ¾” Washers (#107), and two M10 Aircraft Nuts
(#110).
D.)Attach the Weight Glide Post (#17) to rear of Lower Pulley Frame. Secure the top hole
with one 3 1/8” x 1 ¾” Bracket (#36), one M10 x 2 ½” Carriage Bolt (#88), one Ø ¾”
Washer (#107), one M10 Aircraft Nut (#110). Secure the lower hole with one M10 x 2 ½”
Allen Bolt (#95) and one Ø ¾” Washer (#107).
E.) Slide the Sliding Weight Post (#23) to the Weight Glide Post from top. Make sure the
triangular bracket on Sliding Weight Post is facing upward.
F.) Attach the Rear Upper Frame (#18) to Weight Glide Post. Secure the lower hole with one
3 1/8” x 1 ¾” Bracket (#36), one M10 x 2 ½” Carriage Bolt (#88), one Ø ¾” Washer
(#107), one M10 Aircraft Nut (#110). Secure the top hole with one M10 x 2 ½” Allen Bolt
(#95) and one Ø ¾” Washer (#107).
G.)Attach the Rear Upper Frame to the Rear Top Beam (#6). Secure Rear Upper Frame,
Rear Top Beam, and Middle Vertical Frame together with two M10 x 2 ½” Carriage Bolts
(#88), two Ø ¾” Washers (#107), and two M10 Aircraft Nuts (#110).
H.)Securely tighten all Nuts and Bolts installed in Step-1, Step-2, and Step-3.
11

Marcy Fitness www.marcyfitness.co.uk
DIAGRAM 3
12

Marcy Fitness www.marcyfitness.co.uk
STEP 4 (See Diagram 4)
A.) Attach the Butterfly Base (#11) to the front of Middle Vertical Frame (#9). Attach the
Butterfly Pulley Bracket (#14) to the Middle Vertical Frame. Secure them together with two
M10 x 2 ½” Carriage Bolts (#88), two Ø ¾” Washers (#107), and two M10 Aircraft Nuts
(#110).
B.) Attach the Butterfly Stopper (#31) to Butterfly Base. Secure it with two M6 x 3/8” Allen Bolts
(#58).
C.)Attach the Backrest Board (#39) to Middle Vertical Frame. Secure it with two M8 x 2 3/8”
Allen Bolts (#103) and two Ø 5/8” Washers (#106).
DIAGRAM 4
13

Marcy Fitness www.marcyfitness.co.uk
STEP 5 (See Diagram 5)
A.) Insert the pivot on the Right Butterfly (#13) into the hole on the Butterfly Base from bottom.
Secure it with one Lock Ring (#35), one Ø ¾” Washer (#107), and one M10 x 5/8” Allen Bolt
(#87). Push the Butterfly Arm Foam Roll (#64) to Right Butterfly. Repeat same step to install
the Left Butterfly (#12).
B.) Insert two Swivel Pulley Brackets (#15) into the holes on the Butterfly Pulley Bracket (#14).
Secure each Swivel Pulley Bracket with one M12 x 5” Hex Bolt (#100), two Ø 1” Washer
(#108), and one M12 Aircraft Nut (#111). Do not over tighten the Nuts. Make sure the
Brackets are able to swivel.

Marcy Fitness www.marcyfitness.co.uk
DIAGRAM 5
14

Marcy Fitness www.marcyfitness.co.uk
CABLE LOOP DIAGRAM
15

Marcy Fitness www.marcyfitness.co.uk
STEP 6 (See Diagram 6 & Cable Loop Diagram)
A.) Attach one end of 287cm Butterfly Cable (#45) to the clip on Left Butterfly (#12). Draw the Cable
to the left Swivel Pulley Bracket (#15).
B.) Attach a Pulley (#62) and two Cable Retainers (#78) to the Bracket.
C.)Secure them with one M10 x 2” Allen Bolt (#94), two Ø ¾” Washers (#107), and one M10 Aircraft
Nut (#110).
D.)Draw the Cable around the Pulley then downward. Attach an Angled Floating Pulley Bracket (#52)
to the Cable. Repeat Procedure B above to install a Pulley with two Cable Retainers (#78). Draw
the Cable around the Pulley then upward to the right Swivel Pulley Bracket. Let the Bracket
hanging for now.
E.) Repeat Procedure C above to install a Pulley and Cable Retainers to the Bracket.
F.) Draw the Cable around the Pulley then clip to the Right Butterfly (#13).

Marcy Fitness www.marcyfitness.co.uk
16