Titan Lab Kommander User manual
Device Overview
3
6
2
5
1
4
1
12Left / Right Buttons
34Jack 1 / Jack 2
5LED Indicator
6Universal Mount
LED Indicator
LED Activity Status
ANT Active3 Flashes Red
1 Flash Blue BLE Connected
Pairing
Cycle Computer (Private ANT)
3Kommander may appear as a Shift, Remote, or
groupset depending on the cycle computer.
BLE
The device must be paired to the system as a BLE
keyboard in order to control applications. These are
generic instructions, actual devices may differ.
1Press any button to wake the device. The indicator
will flash red 3 times indicating starting in ANT mode.
2On the connecting device (computer or other) search
for BLE keyboard.
3Connect to 'Skommander'
The device must be paired to the cycle computer before
it can control functions.
NOTE: Ant mode turns off if BLE is connected. It
assumes you're indoors and wish to control a BLE
device.
1Press any button to wake the device. The indicator
will flash red 3 times indicating starting in ANT mode.
2Initiate a search for new sensors
4Once connected, Kommander will transmit its
capabilities. Some cycle computers may ask you to
configure the buttons while others have set
functions.
A rubber o-ring is included for round, ovalized and alternative
mounting such as under a stem while using remote buttons
attached to the jacks, or TT/Triathlon configurations.
Soft Mount Installation
Select the location for the remote and hold remote against
the bar.
1
Hook the bottom of the o-ring onto the lower device
mounting tab.
2
While holding the device in place, apply tension to the
o-ring while wrapping it around the bar and hook the
second end over the other mounting tab.
3
1
2
2
1
© 2021 Titan Lab Inc
Version 1.00 Feb 2021
T
Kommander Instructions
1
2
3
4
Hard Mount Installation
Two hardmounts are included. One for 31.8mm and one for
26.2mm round handlebars. Both can be installed in the same
manner.
12
3
4
Insert and tighten the bolt such that the mount cannot
move.
4
Push the mount over the handlebar and position
3
Remove the bolt and stretch open the mount
2
Select the location for the remote. The suggested location
is to the right of the stem far enough from the stem to
allow access to the jacks for accessories
1
5
Normal
Reversed
5Slide the device into the mount from the right side.
5
*LED not visible in
reverse mounting
Replacing the Battery
1
6
4
1
2
3
4
5
6
Specifications
Specification Value
CR1632 (3v)Battery Type
Battery Life Approximately 1000 hrs
(Subject to firmware changes)
Waterproof Rating IPX7 (1meter 30 minutes)
Operating
Temperature Range
From -10° to 50°C
(battery performance may be
degraded at high and low
temperatures)
Expansion Jacks MMCX with Multifunction
Digital (Shell GND, Pin Vdd pullup)
Analog (0 - 3v)
Ouput (3v @ <1ma continous)
© 2021 Titan Lab Inc
1Using the Battery Tab , rotate the cap counter-
clockwise until the stop.
2Lifting the tab should remove the cap with the
battery.
3The battery has a loose fit with the cap so can be
easily removed by the edge or gravity
4Place a new CR1632 with the negative (-) side
exposed, positive (+) side in the battery cap.
5In a rotated position, push the cap into the body
and rotate the tab clockwise.
Kommander uses a toolless battery replacement. Once
you have removed the Kommander from the mount the
following directions can be used to install a new battery.
Kommander's default configuration corrosponds to populare
cycling software commands.
General response may depend on the game mode you're in.
The table below shows functions for each ride game mode.
The cycle computer has up four (4) available buttons in ANT
mode. Some cycle computers have the ability to customize
these buttons and and click types, while others have set
functions. Some may not be able to use Channel 3 and 4.
Future firmware updates will enable the Jacks to be
remapped to Channel 1 and 2.
Future firmware updates may add functionality and
configurability not described in this manual.
BLE - HID Keyboard
Short Left Arrow + page down
Long Sequence 1,2,3….9 Tab (only once per hold)
Double Spacebar Keyboard Down
Right Arrow + Page up
Right ButtonLeft Button
ANT - Remote Mode
Channel 1
Short, Double, Long
Channel 2
Right Button
Left Button Jack 1 Jack 2
Channel 3 Channel 4
Short Navigate
Left
Long
Double Turn Around
Navigate
Right
Right ButtonLeft Button
Freeride FreerideWorkout Workout
Increase
difficulty (ftp)
Decrease
difficulty (ftp)
Skip Workout
Segment
Powerup
Camera View
Future Updates / Features
Kommander Instructions
