Titan TTB517STP User manual

Original Instructions_MNL_TTB517STP_GB_V04_130523
TTB517STP
25mm
Nailer/Stapler
Barcode: 5052931216253
WARNING! Read the instructions before using the product!

25MM NAILER/STAPLER TTB517STP
Congratulations on your purchase of a TITAN power tool from
TITAN Power Tools (UK) Ltd. We want you to continue getting the
best performance from it so this handbook includes information
on safety, handling and care. Please retain this handbook in case
you need to refer to any of the information in the future.
Your TITAN power tool comes with a 2 year guarantee, so should
it develop a fault within this period contact your retailer.
This TITAN product carries a 2 year guarantee. If your product develops a fault
within this period, you should, in the first instance contact the retailer where the item was
purchased.
This guarantee specifically excludes losses caused due to:
- Fair wear and tear
- Misuse or abuse
- Lack of routine maintenance
- Failure of consumable items (such as batteries)
- Accidental damage
- Cosmetic damage
- Failure to follow manufacturer’s guidelines
- Loss of use of the goods
This guarantee does not affect your statutory rights. This guarantee is only valid in the UK.
GUARANTEE

TTB517STP by TITAN
GB
IE
03
13
16
19
20
21
In more detail...
Product functions
Care and maintenance
Trouble shooting
Recycling and disposal
EC declaration of conformity
12
03
04
05
10
Getting started...
Your product
Technical and legal information
Before you start
These instructions are for your safety. Please read through them thoroughly
before use and retain them for future reference.
Let’s
get started…

TTB517STP by TITAN
Getting started...
GB
04
Your product
Your product
1. Lever for loading magazine
2. On/off switch
3. Impact control selection wheel
4. Nailer head
5. Plastic protection cover
6. Soft grip handle
7. Trigger
8. Magazine
9. Slider
IE
9
8
2
6
1
7
4
3
5

05
TTB517STP by TITAN
Getting started...
GB Technical and legal
information
Technical specifications
General
Input Voltage> : 230 -240V, 50 Hz, 9A
Max.Firing speed
> Max.Length of nail
>
IE
VIBRATION
The European Physical Agents (Vibration) Directive has been brought in to help
reduce hand arm vibration syndrome injuries to power tool users. The directive
requires power tool manufacturers and suppliers to provide indicative vibration
test results to enable users to make informed decisions as to the period of time
a power tool can be used safely on a daily basis and the choice of tool.
Further Advice can be found at www.hse.gov.uk
Sound power level L : 88dB(A)
Sound level according to
EN 60745-1
Sound pressure level L : 77dB(A)
pA
WA
Surface grinding a : 4.83 m/s²
h,AG
Uncertainty K : +/-1.5 m/s²
Hand arm vibration according to
EN 60745-1
Uncertainty K , K :3dB(A)
pA WA
The declared vibration emission value should be used as a minimum level
and should be used with the current guidance on vibration.
Calculating the actual period of the actual period off use can be difficult and
the HSE website has further information.
The declared vibration emission been measured in accordance with a
standardised test stated above and may be used to compare one tool with
another. The declared vibration emission value may also be used in a
preliminary assessment of exposure.
Warning! The vibration emission value during actual use of the power tool
can differ from the declared value depending on the ways in which the tool
is used dependant on the following examples and other variations on how the
tool is used: How the tool is used and the materials being ground or cut.
The tool being in good condition and well maintained.
The use the correct accessory for the tool and ensuring it is sharp and in good
condition.
The tightness of the grip on the handles.
And the tool is being used as intended by its design and these instructions.
Max.Magazine Capacity
Nail/Staple Type (IMPORTANT)
>
>
: 20-Nails/Staples- per minute
: Up to 25mm long
: Holds up to 100 nails or 100 staples
: Use Staples: TACWISE Types 91
series．Nails: TACWISE 18ga
Straight Nails. Max Length 25mm
Length of staples
>: 15-25mm long

TTB517STP by TITAN
Getting started...
GB
06
Technical and legal
information IE
This tool may cause hand-arm vibration syndrome if its use is not
adequately managed
Warning! identify safety measures to protect the operator that are based
on an estimation of exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to the trigger time). Note The
use of other tools will reduce the users’ total working period on this tool.
Helping to minimise your vibration exposure risk.
Maintain this tool in accordance with these instructions and keep well
lubricated (where appropriate)
Avoid using tools in temperatures of 10°C or less
Plan your work schedule to spread any high vibration tool use across a
number of days.
Health Surveillance
All employees should be part of an employer’s health surveillance scheme
to help identity any vibration related diseases at an early stage, prevent
disease progression and help employees stay in work.
The tool is double insulated. This means that all the external metal parts
are electrically insulated from the mains power supply. This is done by
placing insulation barriers between the electrical and mechanical
components making it unnecessary for the tool to be earthed.
Be sure the supply is the same as the voltage given on the rating plate.
The tool is fitted with a two-core cable and plug.
Remove the mains plug from socket before carrying out any adjustment or
servicing.
Double insulation:
Important note:
On the product, the rating label and within these instructions you will find
among others the following symbols and abbreviations.
Familiarise yourself with them to reduce hazards like personal injuries and
damage to property.
V~ Volt, (alternating voltage)
A Ampere Hz Hertz kg Kilogram
m/s² Metres per seconds
squared dB(A) Decibel (A-rated)
Symbols

07
TTB517STP by TITAN
Getting started...
GB Technical and legal
information
Safety warnings
GENERAL SAFETY INSTRUCTIONS
WARNING! Read all instructions. Failure to follow all
instructions listed below may result in electric shock, fire and/or
serious injury. The term “power tool” in all of the warnings listed
below refers to your mains operated(corded) power tool or
battery operated (cordless) power tool.
1) WORK AREA
Keep work area clean and well lit. Cluttered and dark areas invite
accidents.
Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
>
>
>
IE
Caution / Warning. Wear hearing protection.
Read the instruction
manual. Wear eye protection.
Wear respiratory protection.
This product is of protection class II. That means it is equipped with
enhanced or double insulation.
The product complies with the applicable European directives and
an evaluation method of conformity for these directives was done.
WEEE symbol. Waste electrical products should not be disposed
of with household waste. Please recycle where facilities exist.
Check with your Local Authority or local store for recycling advice.
yyWxx Manufacturing date code; year of manufacturing (20yy)
and week of manufacturing (Wxx);

TTB517STP by TITAN
Getting started...
GB
08
Technical and legal
information
>
>
>
>
>
>
IE
Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the
rate for which it was designed.
Do not use the power tool if the switch does not turn it on and off. Any
power tool that cannot be controlled with the switch is dangerous and must
be repaired.
Ensure the switch is in the off position before making any adjustments,
changing accessories, or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool accidentally.
4) POWER TOOL USE AND CARE
2) ELECTRICAL SAFETY
Power tool plugs must match the outlet. Never modify the plug in any
way. Do not use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of electric shock.
Avoid body contact with earthed or grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords increase the risk of electric
shock.
>
>
>
>
3) PERSONAL SAFETY
Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired or
under the influence of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in serious personal injury.
Use safety equipment. Always wear eye protection. Safety equipment
such as dust mask, non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal injuries.
Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left attached to a rotating part of the power tool may result
in personal injury.
Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
Dress properly. Do not wear loose clothing or jewellery. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
If devices are provided for the connection of dust extraction and
collection facilities, ensure these are connected and properly used. Use
of these devices can reduce dust related hazards.
>
>
>

09
TTB517STP by TITAN
Getting started...
GB Technical and legal
information
SAFETY INSTRUCTIONS FOR NAILER/STAPLER
Secure the workpiece (a workpiece clamped with clamping devices or in
a vice is held more securely than by hand).
Never push in the nailer/stapler head manually (there is danger of injury
when at the same time the trigger is activated unintentionally).
Never use the tool for fastening electrical wiring (contact with electrical
wires can lead to fire and electric shock)
Avoid damage that can be caused by screws, nails and other elements in
your workpiece; remove them before you start working.
Always check that the supply voltage is the same as the voltage indicated
on the nameplate of the nailer/stapler (nailers/staplers with a rating of
230V or 240V can also be connected to a 220V supply).
In case of electrical or mechanical malfunction, immediately switch off the
tool or unplug charger from power source.
We can assure flawless functioning of the tool only when original accessories
are used.
This tool should not be used by people under the age of 16 years.
Do not expose tool to rain.
>
>
>
IE
>
>
>
>
>
>
>
>
>
>
Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to operate
the power tool. Power tools are dangerous in the hands of untrained users.
Maintain power tools. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that may affect the
power tools operation. If damaged, have the power tool repaired before
use. Many accidents are caused by poorly maintained power tools.
Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc., in accordance with
these instructions and in the manner intended for the particular type of
power tool, taking into account the working conditions and the work to
be performed. Use of the power tool for operations different from those
intended could result in a hazardous situation.
5) SERVICE
>
Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power
tool is maintained.

TTB517STP by TITAN
Getting started...
GB
10
Before you start IE
Unpack all parts and lay them on a flat, stable surface.
Remove all packing materials and shipping devices if applicable.
Make sure the delivery contents are complete and free of any damage. If
you find that parts are missing or show damage do not use the product but
contact your dealer. Using an incomplete or damaged product represents
a hazard to people and property.
Ensure that you have all the accessories and tools needed for assembly
and operation. This also includes suitable personal protective equipment.
>
>
>
>
Unpack
(items not supplied)
Suitable personal
protective equipment
You will need
(items supplied)
Nails (25mm) (100pcs)
Staples (22mm) (300pcs)

11
TTB517STP by TITAN
Getting started...
GB Before you start
Inserting Nails and Staples
IE
Only use the nails/staples which are outlined in the technical specifications.
Please keep in mind that nails/staples must be suited to the material they are
used in.
The harder the material is, the shorter the staples or nails should be.
1. Press lever (1) while pulling slider (9) backwards
2. Insert the nail strip into magazine (8) with heads facing upward (maximum
capacity 100/nails)
3. Push slider (9) against nailer head (4) until it snap locks.
4. When inserting a nail/staple strip, it rests against the magazine side which
correponds with the nail symbol on nailer head (4).
Fig. 1
9
8
1
4
A
B
C
Fig. 2

TTB517STP by TITAN
In more detail…
GB
IE
In more detail…
12
20
19
16
13
Product functions
Care and maintenance
Trouble shooting
Recycling and disposal
EC declaration of conformity 21

13
TTB516NAL by TITAN
In more detail…
GB
Intended use
Product functions
The machine is intended for tacking of cardboard, insulating material, fabric,
thin plywood, foils, leather and similar materials and similar materials on
wooden surfaces or similar e.g. mdf, plywood; when used in accordance with
these instructions. The machine is not suitable for the attachment of wall and
ceiling panelling.
Any use beyond these parameters (different media, applied force) or any
changes to the product (use on non original accessories, alteration etc) can
lead to serious risks and is regarded as use that is contrary to the intended
purpose. The operator is liable for any damage caused by improper use, and
all main function warranty will be valid.
Loading Nails/staples
Switch off and unplug before insert nails, turn tool upside down (Fig.3)
Press lever (1) while pulling slider (9) backwards Insert the nail strip into
magazine (8) with heads facing upward (maximal capacity 100 nails)
Push slider (9) against nailer head (4) until it snap locks.
When inserting a nail strip (not supplied with the tool) tilt the tool in such
a way, that the nail strip rests against the magazine side which corresponds
with the nail symbol on nailer head (4) nail points upward.
IE
Fig. 3 Fig. 4
>
>
>
>
IMPORTANT: Use Staples: TACWISE Types 91 series.
Nails: TACWISE 18ga Straight Nails. Max Length 25mm.
9
8
1
4
A
B
C

14
TTB517STP by TITAN
In more detail…
GB
Product functions
Firmly press nailer head (4) against the workpiece until there is no gap
between the nailer head (4) and the workpiece.
Briefly press trigger (7) and then release again.
Trigger (7) is locked as long as you do not press nailer head (4) against the
workpiece, thus preventing accidental operation.
At 20 shots/min,tacker should be allowed to cool down after 30 minutes as
it is only rated for short-time duty.
>
>
>
NOTE: remove all staples/nails from the magazine
after each use.
IE
Fig. 5
Operating the tool
>
4
NOTE: when using a nailer/stapler it is best practice
to have one hand on the rear of the tool, opposite
the nailer head. This insures full penetration of the
longer nails/staples whilst keeping your hand away
from the nailer head.

15
TTB517STP by TITAN
In more detail…
GB
Impact control
Product functions
IE
>
>
>
>
Indicator (3) shows the selected impact level.
“-” for thin and light materials such as foils and fabrics.
“+” for thick and tough materials such as hard woods and walls.
Before starting a job, find the optimal impact level by testing
out on spare material.
With wheel (3) the required impact level can be selected in steps.
3
Fig. 6
In the unlikely event that nails become jammed, follow these instructions to
remove them
Unblocking jammed fasteners
>
>
>
>D
D2 D3
D1
Remove the plastic protection cover D (Fig. 7)
Remove the plate retaining bolts D1
Remove the safety mechanism retaining plate D2
Remove the firing pin retaining plate D3 (Fig. 8)
Fig. 7
Fig. 8

16
TTB517STP by TITAN
In more detail…
GB
IE
Care and maintenance
Switch off and remove plug.
Clean the ventilation grill and on / off button with a soft brush.
Make sure that the ventilation openings are always clear and clean.
Use a damp cloth with water to clean your stapler, but do not use alcohol,
caustic cleaner.
General operation
Check the product, its power cord and plug as well as accessories for
damage before each use. Do not use the product if it is damaged or shows
wear.
Always hold the product correctly. Keep the handle dry to ensure safe
support.
Ensure that the air vents are always unobstructed and clear.
Clean them if necessary with a soft brush. Blocked air vents may lead to
overheating and damage the product.
Switch the product off immediately if you are disturbed while working by
other people entering the working area.
Do not overwork yourself. Take regular breaks to ensure you can
concentrate on the work and have full control over the product.
>
>
>
>
>
>
After use
Switch the product off, disconnect it from the power supply and let it cool
down on a minimum of 20 minutes before storing.
Store the product and its accessories in a dry, frost-free place.
Always store the product in a place that is inaccessible to children.
>
>
>
>
>
>
>
4 Golden rules for servicing

17
TTB517STP by TITAN
In more detail…
GB
IE
Care and maintenance
Power cord
If the power cord is damaged, it must be replaced by the manufacturer,
its service agent or similarly qualified persons in order to avoid a safety
hazard.
>
UK plug
If you need to replace the fitted plug, then follow the instructions
below.
IMPORTANT: The wires in the mains lead are coloured in accordance
with the following code:
Blue – Neutral Brown – Live
As the colours of the wire in the mains lead of this product may not
correspond with the coloured marking identifying the terminals in your
plug,proceedasfollows.Thewire,whichiscolouredblue,must be
connected to the terminal, which is marked with N or coloured black.
The wire, which is coloured brown, must be connected to the terminal,
which is marked L or coloured red.
Only fit an approved 13 Amp BS 1363 or BS 1363/A plug and the
correctly rated fuse.
If in doubt, consult a qualified electrician.
WARNING! Never connect live or neutral wires to the earth
terminal of the plug.
13AMP fuse
approved to
BS 1362
Brown L(Live)
Cable grip
Outer sleeve
firmly clamped
Connect
Blue to
N(Neutral)
NOTE: If a moulded plug is fitted and has to be removed take
great care in disposing of the plug and severed cable, it must be
destroyed to prevent engaging into a socket.

18
TTB517STP by TITAN
In more detail…
GB
IE
Repair
Care and maintenance
This product does not contain any parts that can be repaired by the
consumer. Contact a qualified specialist to have it checked and repaired.
Storage
Clean the product as described above.
Store the product and its accessories in a dry, frost-free place.
Always store the product in a place that is inaccessible to children. The
ideal storage temperature is between 10 and 30°C.
We recommend using the original package for storage or covering the
product with a suitable cloth to protect it against dust.
>
>
>
>
Transportation
Switch the product off and disconnect it from power supply before
transporting it anywhere.
Attach transportation guards, if applicable.
Always carry the product by its handles.
Protect the product from any heavy impact or strong vibrations which may
occur during transportation in vehicles.
Secure the product to prevent it from slipping or falling over.
>
>
>
>
>
>

19
TTB517STP by TITAN
In more detail…
GB
IE
Trouble shooting
Trouble shooting
Suspected malfunctions are often due to causes that the users
can fix themselves. Therefore check the product using this section.
In most cases the problem can be solved quickly.
WARNING! Only perform the steps described within these
instructions! All further inspection, maintenance and repair work
must be performed by an authorised service centre or a
similarly qualified specialist if you cannot solve the problem
yourself!
Problem Possible cause
1. Product does
not start 1.1 Not connected to power supply
1.2 Product not switch on
1.3 Power cord or plug
is defective
1.4 Other electrical
defect to the product
2. Product does
not reach full
power
2.1 Extension cord not
suitable for operation
with this product
2.2 Power source (e.g.
generator) has too low
voltage
2.3 Air vents are
blocked
3. Fasteners jam
in tool 3.1 Wrong size fasteners
3.2 Driver channel worn
3.3 Bent fasteners
3.4 Loose magazine/nose
screws
3.5 Broken/chipped driver
1.1. Connect to power
supply
1.2 Switch ON
1.3. Check by a
specialist electrician.
1.4. Check by a
specialist electrician
2.1. Use a proper
extension cord
2.2. Connect to another
power source
2.3. Clean the air vents
3.1. Use only
recommended
fasteners
3.2. Replace nailer
/stapler
3.3. Discontinue using
these fasteners
3.4. Tighten all screws
3.5. Replace
nailer/stapler
Solution

20
TTB517STP by TITAN
In more detail…
GB
IE
Recycling and disposal
Recycling and disposal
Waste electrical products should not be disposed of with
household waste. Please recycle where facilities exist.
Check with your Local Authority or local store for recycling
advice.
>