Titon TP 342A User manual

ventilation systems
Product Manual
CME3 Q Plus A TP 332A
CME3.1 Q Plus A TP 342A
Extract Ventilation Unit with Volt Free Boost Switching
CME3 Q Plus HA TP 332HA
CME3.1 Q Plus HA TP 342HA
Extract Ventilation Unit with Humidity & Volt Free Boost Switching
CME3 Q Plus HA LS TP 334HA
CME3.1 Q Plus HA LS TP 342HALS
Extract Ventilation Unit with Humidity & LIVE Boost Switching
EN
)
RAPeak

Warnings, Safety information and Guidance
Important Information
Read these instructions fully before the installation of this appliance
1. Installation of the appliance and accessories must be carried out by a
qualied and suitable competent person and be carried out in clean,
dry conditions where dust and humidity are at minimal levels.
2. All wiring must conform to current I.E.E. Wiring Regulations
and all applicable standards and Building Regulations.
3. The appliance must be connected to a local double pole isolation switch with
a contact separation of at least 3mm. Ideally located adjacent to the unit.
4. The appliance must be earthed.
5. Units are suitable for 220-240V~ 50-60Hz single phase with a fuse rating of 3A.
6. The unit must be stored in a clean and dry environment.
7. Do not install the appliance in areas where the
following may be present or occur;
xExcessive oil or a grease laden atmosphere,
xCorrosive or ammable gases, liquids or vapours,
xAmbient temperatures above 40°C or below -5°C,
xHumidity levels above 90% or is a wet environment.
8. The appliance is not suitable for installation to the exterior of the dwelling.
9. This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance
in a safe way and understand the hazards involved.
10. Children should be supervised to ensure that
they do not play with the appliance.
11. Ensure that external grilles are located away from any ue
outlet, in accordance with relevant Building Regulations.
12. The unit must not be connected to a tumble dryer.
13. The unit must not be connected to a cooker hood.
14. Precautions must be taken to avoid the back-ow of
gases into the room from an open ue appliance.
15. Ensure all ducting is free from debris and
blockages before switching on the unit.
16. The unit uses a 230V ~ 50-60Hz supply and contains rotating mechanical
parts. ISOLATE the unit from mains power supply and allow sucient time
for all moving parts to stop before undergoing any Servicing or Maintenance.
2

Explanation of symbols on the appliance
Symbol Denition
Read instruction Manual.
Risk of Electric Shock.
General hazard safety alert.
Wait until all machine components have completely
stopped before touching them.
Disconnect the mains supply before removing this
cover.
+
Disconnect the mains supply before removing this
cover.
Before obtaining access to terminals or removing this
cover, all supply circuits must be disconnected.
3

Warnings, Safety information and Guidance
Important Information � � � � � � � � � � � � � � � � � � � � �2
Explanation of symbols on the appliance� � � � � � �3
Product Overview
Package Contents� � � � � � � � � � � � � � � � � � � � �5
Dimensions� � � � � � � � � � � � � � � � � � � � � � � � � � � � � �6
Component Identication � � � � � � � � � � � � � � � � � � �7
Product Features� � � � � � � � � � � � � � � � � � � � � �8
Installation
Fixing � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �10
Ducting Connections � � � � � � � � � � � � � � � � � � � � �10
How to convert the Port Cover � � � � � � � � � �11
Wiring
Wiring Connection Access � � � � � � � � � � � � � � � � �12
CME3 & 3�1 Q Plus A & HA � � � � � � � � � � � � � � � � �12
CME3 & 3�1 Q Plus HA LS � � � � � � � � � � � � � � � � � �14
Cable Retention � � � � � � � � � � � � � � � � � � � � � � � � �16
Commissioning
CME3 & 3�1 Q Plus A� � � � � � � � � � � � � � � � � � � � � �17
Control Parameters� � � � � � � � � � � � � � � � � � �17
Commissioning Controls� � � � � � � � � � � � � � �18
Boost Overrun � � � � � � � � � � � � � � � � � � � � � � �18
CME3 & 3�1 Q Plus HA � � � � � � � � � � � � � � � � � � � �19
Control Parameters� � � � � � � � � � � � � � � � � � �19
Commissioning Controls� � � � � � � � � � � � � � �20
Boost Overrun � � � � � � � � � � � � � � � � � � � � � �21
Humidity Sensor � � � � � � � � � � � � � � � � � � � � �21
CME3 & 3�1 Q Plus HA LS � � � � � � � � � � � � � � � � � �22
Control Parameters� � � � � � � � � � � � � � � � � � �22
Commissioning Controls� � � � � � � � � � � � � � �23
Boost Overrun � � � � � � � � � � � � � � � � � � � � � �24
Humidity Sensor � � � � � � � � � � � � � � � � � � � � �24
Reset Information� � � � � � � � � � � � � � � � � � � � � � � �25
Hardware Reset� � � � � � � � � � � � � � � � � � � � � �25
Technical
Product Fiche � � � � � � � � � � � � � � � � � � � � � � � � � � �26
Maintenance
Routine maintenance � � � � � � � � � � � � � � � � � � � � �28
Cleaning Exterior� � � � � � � � � � � � � � � � � � � � �28
Access to the Interior for Cleaning � � � � � � �28
Removal of the Scroll Top � � � � � � � � � � � � � �29
Cleaning Interior � � � � � � � � � � � � � � � � � � � � �29
Service Record � � � � � � � � � � � � � � � � � � � � � � � � � �30
Installed by � � � � � � � � � � � � � � � � � � � � � � � � � � � � �31
Environmental Information � � � � � � � � � � � � � � � �31
Contents
4
When this document is viewed
as a PDF the headings & sub
headings on this page are hyper
links to the content. Additionally the
page numbers in this document are
hyper links back to this contents page.

Product Overview
This manual is for the range of Titon CME3 & 3.1 Q Plus Extract ventilation units. All CME3 &
3.1 Q Plus units are designed for continuous extract ventilation of multiple rooms, for example
bathrooms, kitchens, utility areas and toilets. The units use a highly ecient backward curved
Centrifugal impeller coupled to a high eciency EC motor. The range consists of:
xCME3 Q Plus A TP 332A
xCME3.1 Q Plus A TP 342A
Extract Ventilation Unit with Volt Free Boost Switching
xCME3 Q Plus HA TP 332HA
xCME3.1 Q Plus HA TP 342HA
Extract Ventilation Unit with Humidity & Volt Free Boost Switching
xCME3 Q Plus HA LS TP 334HA
CME3.1 Q Plus HA LS TP 342HALS
Extract Ventilation Unit with Humidity & LIVE Boost Switching
Package Contents
xCME3 or CME3.1 Unit
xPort Covers / Convertible to Ø100mm adaptors
xProduct Manual
xEuP Sticker
xProduct Fiche
All shortages or damage must be immediately reported to the supplier.
GB Patent GB 2491516
5

Dimensions
This diagram details the overall size of the unit and the additional space required
around the unit to allow for commissioning and future servicing and maintenance
85
205
15
310
150 360
340
72.5
24
252
352
460
490
Ports Ø125
Service Void
All Dimensions in mm DO NOT BOX IN UNIT
6

Component Identication
All Dimensions in mm
7
Lid
Lid Screw
Scroll Top
Output Port
Base
Cable Clamps
Port Cover

Product Features
CME3 Q Plus A
CME3.1 Q Plus A
CME3 Q Plus HA
CME3.1 Q Plus HA
CME3 Q Plus HA LS
CME3.1 Q Plus HA LS
The CME Q Plus is controllable by various
volt-free switches and sensors.
Mains switching can be achieved by use
of the Titon Boxed Relay 5A TP 505.
The CME Q Plus HA
LS is controllable
by various mains
switches.
Mains
switching
No No Yes
Volt free
switching
Yes Yes No
Continuous
Speed
The normal running speed of the unit.
Continuous Speed is congured using a stepless
independent fan control potentiometer
Boost
Speed
An increased speed providing higher extract air ow. Boost Speed is
congured using a stepless independent fan control potentiometer
Boost
Switching
The Boost Speed can be enabled by
connection of a volt free one-way switch,
or combined with the Setback Speed
with the 3 position switch TP508.
The Boost Speed
can be enabled by
connection of a mains
one-way switch, or
combined with
the Setback Speed
with the 3 position
switch TP508.
Boost
Overrun
Timer
The timer maintains the Boost Speed for a specic time variable between
0 and 30 minutes after Boost Speed is disengaged. The Boost Overrun
Timer time is congured using stepless independent potentiometer
8

CME3 Q Plus A
CME3.1 Q Plus A
CME3 Q Plus HA
CME3.1 Q Plus HA
CME3 Q Plus HA LS
CME3.1 Q Plus HA LS
Setback
Speed
The reduced ventilation rate is automatically
set at the mid point between minimum
speed and the selected Continuous Speed.
Setback Speed,
reduced ventilation
rate, is congured
using a stepless
independent fan
control potentiometer.
Setback
Switching
Is enabled by connection of a latching volt-free
one-way switch, or combined with the Boost
Speed with the 3 position switch TP 508.
Enabled by connection
of a latching mains
one-way switch, or
combined with the
Boost Speed with the 3
position switch TP 508.
Integrated
Humidity
Sensor
NA
The units are tted with an Integrated Humidity
Sensor. This continuously monitors the relative
humidity (RH) of the extracted air. The fan
speed increases proportionally between
Continuous Speed & Boost Speed depending on
the measured %RH;
RH Set
Point
-10% +10%
Continuous
Speed
Boost
Speed
The Humidity Sensor’s set point is variable from
55%RH to 85%RH and is congured using a
potentiometer.
9

Installation
Fixing
The unit must be securely xed
to a single smooth at surface.
Any orientation is possible.
Locate a site for mounting the Titon CME,
take into consideration the position of:
xThe rooms to be ventilated
xThe Electrical services
xThe exhaust port orientation.
Ensure there is adequate access
for installation and maintenance,
see Dimensions for sizes.
Securely mount the unit through the mounting
holes on the casing using the appropriate
xings for the substrate and the CME.
Ensure the unit is not distorted by
the xings or mounting surface.
The xing slots on the unit are 6mm wide,
it may be necessary to use washers to
prevent damage to the CME's xing slots.
Tighten screws by hand, DO NOT over tighten
screws or use power tools.
Ducting Connections
Titon recommend that:
1. Ø125mm ducting is used for the
connection of the Output Port to Outside.
2. Ø125mm or Ø100mm ducting is used
for connection to the other ports.
3. A minimum distance of 200mm
between the CME unit and any
sharp bends in duct work.
4. Ducting should be insulated
where it passes through
unheated areas and voids.
5. Unit should be insulated when
tted in unheated area.
6. Where a duct extends externally above
roof level the section above the roof
should be insulated or a condensate trap
should be tted just below roof level.
7. Where ducts pass through re barriers,
they must be appropriately re stopped in
accordance with the requirements of Part
B Building Regulations (England & Wales).
8. A ducting condensate drain
must be tted to vertical Output
Port to Outside duct work.
9. Condensate drain pipe work must be
adequately secured, installed to have
a minimum 5° fall and be insulated if
any part of the pipe passes though an
unheated void. All insulation to be the
equivalent of at least 25mm of insulating
material with a thermal conductivity
of 0.04 W/(mK).
10. Ducting must be installed in such a way
that resistance to airow is minimised.
11. Ducting connected to the Output Port
to Outside must be to the external
air outside the building envelope.
12. All ducting joints including those
to the CME unit’s Duct Ports and
Convertible Port Covers must be
permanently connected and sealed.
13. Do not distort ducting, Convertible
Port Cover or Duct Ports.
10