TMI Products vk61 Installation manual

English
Center Hour hand
Center Minute hand
Center 1/5 chronograph second hand
Date
Small second hand
Chronograph minute hand
24 hour hand
Chronograph hour hand
Button A (START / STOP)
Button B (RESET)
Set the time
1) Pull out the crown to the second click position.
2) Turn the crown to set hour and minute hand (Check that AM / PM is set correctly).
3) Push the crown back into the normal position.
* If the crown is pulled to the second position while the chronograph is started, the chronograph hands will continue to
move. This is not a malfunction.
Set the date
1) Pull out the crown to the first click position.
2)
Turn the crown clockwise for date setting.
*
Do not set the date between 9:00PM and 3:00AM, otherwise the day may not change properly. If it is necessary
to set the date during that time period, first change the time to any time outside it, set the date and then reset
the correct time.
3) Push the crown back into the normal position.
OPERATION MANUAL
VK61 / VK63 / VK64 / VK67 / VK68 / VK73 / VK83
DISPLAY AND CROWN/ BUTTON OPERATION
TIME SETTING
O
O
O
6H
6H
X
12H
9H
12H
10H
9H
X
3H
X
2H
3H
X
X
9H
2H
4H
VK73
VK83
O
<< VK61 >>
<< VK63 >>
<< VK64 >>
<< VK67 >>
<< VK68 >>
<< VK73 >>
<< VK83 >>
VK61
VK63
VK64
VK67
VK68

English
Method 1
1) Set the crown to the normal position
2) Touch the AC terminal of circuit block and the switch spring with conductive
tweezers to reset the circuit.
3)
The small second hand will move at two-second interval for 10 seconds as a
demonstration. (not applicable to VK64)
Method 2
1) Pull out the crown to the second click position.
2) Press the button B for two seconds and release the button.
3) Push the crown back to the normal position.
4) The small second hand will move at two-second interval for 10 seconds as a demonstration.
(not applicable to VK64)
* If the crown is operated within these 10 seconds, the two-second interval movement will not be activated.
(not applicable to VK64)
* It is not necessary to set the chronograph hands after the battery is exchanged. If the chronograph hand positions are
incorrect, following below procedure all the chronograph hands will be reset to "0" position
[ Standard measurement : e.g. 100m race ]
Press the buttons in the following order : A A B
* * *
VK61 / VK63 / VK64 / VK68 / VK73 : 60 minutes
* The chronograph can measure up to VK67 : 12 hours and
VK83 : 20 minutes
VK61 / VK63 / VK64 / VK68 / VK73 : 60 minutes
chronograph stops after a measurement for VK67 : 12 hours
VK83 : 20 minutes
* To restart the chronograph function :
VK61 / VK63 / VK64 / VK67 / VK68 / VK73 : Press button A
VK83 : Press button B (to reset the chronograph minute hand to "0" position) then press button A
* During the chronograph operation, button B (reset) can be pushed. It will not cause any problem.
Button A
Button A
Button B
(START)
(STOP)
(Reset)
HOW TO RESET (AFTER BATTERY CHANGE)
HOW TO USE THE CHRONOGRAPH
START
Press button A to start the
chronograph. The
chronograph hands wil start
moving.
Press button B to reset the
chronograph. All the
chronograph hands will be
reset to "0" position
STOP (Finish)
RESET
Press button A again to stop
the chronograph. The
chronograph hands stop to
indicate the elapsed time.
A
A
B

English
[ Accumulated elapsed time measurement : e.g. basketball game ]
Press the buttons in the following order : A A / A …A B
* Restart and stop of the chronograph can be repeated as many times as necessary by pressing button A.
SII Products
START
STOP / RESTART
STOP
RESET
A
A
A
B