TMS FOSTER 41802 User manual

Made In China
ASSEMBLY INSTRUCTIONS
ASSEMBLY
REQUIREMENTS
2 HOURS
Assembly Time
(Approximate)
2 -Person Assembly Tools Required (Not Provided):
Phillips Screwdriver
Flat Head Screwdriver
Thank you for purchasing our product!
1/11
ASSEMBLY PREPARATION
1. Remove all packaging materials, staples and packing straps from the carton.
2. Refer to Parts List and Hardware List , and ensure parts and hardware are complete before you start assembly.
Contact customer service for missing parts.
3. Place all wooden parts on a clean, flat and soft surface (e.g. carpet or rug) to prevent parts from getting scratched.
SAFETY PRECAUTION:
1. KEEP ALL HARDWARE PARTS OUT OF REACH OF CHILDREN.
2. DISPOSE PLASTIC PACKAGING MATERIAL IMMEDIATELY TO AVOID ANY RISK OF SUFFOCATION TO
CHILDREN AND ANIMALS.
TIPS FOR ASSEMBLY:
1. Allow ample room for assembly and in close proximity to where product will be placed.
2. Assemble the product on a surface that does not scratch or damage the exterior gloss and finish of the furniture.
3. Check all of the parts and quantities are included before assembly.
4. Identify all of the parts, hardware and quantities required for each step.
5. During assembly, do not over-tighten any fittings as this may cause damage.
6. DO NOT USE POWER TOOLS TO ASSEMBLE THIS PRODUCT.
7. Always place the product on a flat, level surface.
8. Do not sit or stand on the partially assembled product; only use the product for which it is intended.
CARE AND MAINTENANCE
CLEANING - Use a slightly damp cloth to clean the product. Do not use bleach or abrasive cleaning material.
FITTINGS - Check all the fittings periodically and re-tighten as necessary. Do not use the product if any of the parts is
damaged or broken.
This product is for indoor and household use only - not for commercial use.
2 DRAWER FILING CABINET
Please refer and use this assembly instruction to assemble the product.
Contact our customer service department in case there are any missing or damage parts or hardware.
We appreciate your business!

Cam-lock
Wood Dowel
Cam-bolt
Hardware List
ITEM PART QTY ITEM PART QTY
A
4 pcs
8 pcs
8 pcs
DESCRIPTION DESCRIPTION
Metal Rod
6*35mm
15*12mm
B
C
G
I
4*40mm
H
ASSEMBLY INSTRUCTIONS
2/11
J
K
D
F
E
12 pcs
12 pcs
8 pcs
4*16mm
Knob
Knob Bolt
Drawer Glide
4 pcs
Screw
24 pcs
Screw
3*12mm
8*30mm
2 pcs
2 pcs
4 pcs
5*50mm
Screw
4*30mm
Screw
L4 pcs
Screw
M4 pcs
Backply Stopper
3*16mm
2 DRAWER FILING CABINET

ITEM PART QTY
1
2
3
1 pc
4 pcs
DESCRIPTION
Top Panel
Bottom Panel
Left Panel 1 pc
Parts List
3/11
4Right Panel 1 pc
6Leg 4 pcs
5Back Panel 1 pc
ASSEMBLY INSTRUCTIONS
ITEM PART QTY
7
8
9
2 pcs
DESCRIPTION
Drawer Left
Panel
Drawer Right
Panel
10 Drawer Back
Panel
11 Drawer Bottom
Panel
2 pcs
2 pcs
2 pcs
2 pcs
Drawer Front
Panel
2 DRAWER FILING CABINET

1
Parts List
Assembly Overview
4/11
ASSEMBLY INSTRUCTIONS
2
3
4
5
6 6
6
6
7
8
9
10
11
7
8
9
10
11
2 DRAWER FILING CABINET

PANEL
Place Cam-bolt to the designated pre-drilled holes on the panel. Use a Phillips Screwdriver to
tighten Cam-bolt vertically until shoulder is flushed (on the same level) with panel. Do not
over-tighten or under-tighten.
CORRECT
Use a Flat-head Screwdriver to turn
Cam-lock clockwise so it locks onto
the head of the Cam-bolt. Turn until
it is snug (about one half of a turn)
-- over-tightening could damage
Cam-lock or/and Cam-bolt.
CAM-BOLT CAM-LOCK
Tools Required
INSERTING AND TIGHTENING CAM-BOLT
SHOULDER
Instructions For Fastening
CAM-BOLT AND CAM-LOCK
Align the arrow on the Cam-lock to the Cam-bolt
head and insert the Cam-lock. Ensure Cam-lock
is fully inserted.
PANEL
Place Cam-bolt on pre-drilled
hole and screw in vertically.
Shoulder is flushed (on the
same level) with the panel.
Shoulder is above the panel.
PANEL
INSERTING CAM-LOCK
Cam-bolt head
needs to be in centre WRONG
TIGHTENING CAM-LOCK
5/11

STEP 1
STEP 2
Position Bottom Panel (2) vertically as shown, on a material that does not scratch the part.
Align screw holes on Leg (6) to screw holes on (2). Use Phillips Screwdriver to drive Screw (H)
to fasten (6) to (2). Do not tighten (H) completely until both screws are in place on each leg.
12 pcsG
8 pcsH
6/11
a) Place Top Panel (1) and 2x Drawer Panels (7) with interior side facing up, as shown, on
a material that does not scratch its exterior surface.
b) Screw in Cam-bolt (A) into designated holes on (1 & 7). Refer to Page 5 for instructions
on fastening Cam-bolt.
1
7
7
AA
A
A
2
H
6
6
6
6

F2
F2
F2
a) Place Left & Right Side Panel (3 & 4) as shown on a material that does not scratch the
surface of the parts. Next, locate pilot holes for Screw (K) on each part.
b) Position and align screw holes on Drawer Glide Track (F2) to pilot holes on (3 & 4) and use
Screw (K) to fasten (F2). Do not tighten (K) completely until all of the screws are in place.
KK
3
4
STEP 3
STEP 4
4 pcsF2
12 pcs
K
7/11
To install Drawer Glide (F), the Drawer Glide Runner (F1) needs to be detached or separated
from the Drawer Glide Track (F2).
Detach Drawer Glide Runner (F1) from Drawer Glide Track (F2) by sliding out Drawer Slide
Runner (F1) from Drawer Glide Track (F2) until the Trigger Disconnect Lever is visible on (F1)
as shown above. Next, depress the Trigger Disconnect Lever and at the same time slide out
(F1) from (F2).
4 pcs
F
F
T rigger D isconnect
L ever
F1
F2
F1
F2

3
4
2
C
J
DO NOT USE POWER TOOLS
C
B
1
4 pcsB
8 pcs
C
5
3
4
B
STEP 5
STEP 6
4 pcs
C
4 pcsJ
8/11
a) Position the panels with groove edge at the
bottom as shown.
b) Insert Wood Dowel (C) into the designated
holes on Side Panels (3 & 4).
c) Attach Side Panels (3 & 4) to Bottom Panel
(2) via Wood Dowels, and use Screw (J) to
fasten (2) to (3 & 4). Do not tighten the
screws completely until both screws are in
place on each panel.
d) Place the assembly right-side up.
a) Fit Back Panel (5) by inserting the long
edges of (5) into the groove on Left &
Right Panels (3 & 4), and bottom edge
into groove on Bottom Panel.
b) Insert Wood Dowel (C) into the
designated holes on top edge of Side
Panels, and attach Top Panel (1) via
Wood Dowels and Cam-bolts. Check
that top edge of (5) fits into groove on
bottom side of (1).
c) Insert Cam-lock (B) into designated
holes on (3 & 4) then turn clockwise to
lock onto Cam-bolt. Refer to Page 5 for
instructions on fastening
Cam-lock.

STEP 7
STEP 8
4 pcsL
4 pcsM
9/11
DO NOT USE POWER TOOLS
8 pcs
I
LM
LM
5
a) Attach Drawer Left & Right Side Panels (8 & 9) to Drawer Back Panel (10) as shown.
Note: the groove on each panel is at the bottom.
b) Use Phillips Screwdriver to drive Screw (I) to fasten Back Panel to Side Panels. Do not
tighten screws completely until both screws are in place on each panel.
c) Fit Bottom Panel (11) to Drawer Panels (8, 9 & 10) by inserting the edges of (11) into the
groove on respective drawer panels.
I
10
8
9
11
X2
a) Insert Backply Stopper
(M) at each corner to fit
into the groove and
against Back Panel (5).
b) Use Screw (L) to
fasten (M).

Open-end
Open-end
X2
STEP 9
STEP 10
8 pcs
B
2 pcs
D
10/11
4 pcs
F1
12 pcs
K
8
9
10
7
11
D
E
B
G
B
2 pcsE
4 pcs
G
X2
KF1
F1
K
F1
K
a) Insert one end of Metal Rod (G) into the designated holes on Drawer Back Panel (10).
b) Partially insert Cam-bolts on Drawer Front Panel (7) into the designated holes on Drawer
Side Panels (8 & 9). Next, fit front edge of Bottom Panel (11) and the Metal Rod (G) into the
groove and designated holes on (7), respectively, and then attach (7) to (8 & 9) firmly.
c) Insert Cam-lock (B) then turn clockwise to lock Cam-bolt to fasten Drawer Front Panel.
d) Use a Phillips Screwdriver to drive Knob Bolt (E) to fasten Knob (D) to drawer front panel as
shown.
a) On each Drawer completed in STEP 9, locate pilot holes on Side Panels (8 & 9) for
fastening Drawer Glide Runner (F1).
b) Position (F1)to align the designated screw holes on (F1)to pilot holes (Refer to enlarged
drawings). Check that the open-end of (F1) faces the Drawer Back Panel.
c) UseScrew (K) to fasten (F1)to Side Panels (8 & 9). Use a Phillips Screwdriver to drive
(K). Do not tighten (K) completely until all 3 screws are in place.

Insert Drawers.
TO REMOVE DRAWER FROM THE CABINET
a) Slide out the drawer until the Disconnect Lever is visible on F1 on the Left and Right Side of the
drawer.
b) Push DOWN the Disconnect Lever on the Right Drawer Glide (F1) and Push UP the plastic
Stopper on Left Drawer Glide (F1) at the same time and continue to pull out the drawer.
STEP 11
11/11
F1
F2
To insert Drawers:
a) On the Side Panels of the cabinet, bring the ball-bearing slider on Drawer Glide
Track (F2) forward to the front edge of (F2) i.e. towards drawer opening of the desk.
b) Align the back open-end of the Drawer Glide Runner (F1) on each side of the drawer to fit
squarely into the groove on the open front-end of (F2) on the Side and Middle Panels. Be
sure the drawer/F1 is not tilted or angled, and gently push in drawer squarely.
c) When the drawer is pushed in about half way, the Disconnect Lever on (F1) will be engaged
onto (F2) which will make pushing in the drawer again to engage the Lever to the slide
mechanism on (F2). The drawer should now slide smoothly.
d) If the drawer cannot be pushed in or stuck, do not force it in. Remove the drawer and repeat
the steps above.
X2
The assembly of this 2-Drawer Filing Cabinet is complete.