TMS Lewis End Table 72401WHT User manual

Email: [email protected]
Within 30 days from delivery date
Made In China
1/11
DATE: 04-05-2016
ASSEMBLY
REQUIREMENTS
2 HOURS
Assembly Time
(Approximate)
2 -Person Assembly Tools Required (Not Provided):
Phillips Screwdriver
Flat Head Screwdriver
Thank you for purchasing our product!
Please refer and use this assembly instruction to assemble the product.
Contact our customer service department in case there are any missing or damage parts or hardware.
Replacement parts are normally shipped within 2 or 3 days.
We appreciate your business!
ASSEMBLY PREPARATION
1. Remove all packaging materials, staples and packing straps from the carton.
2. Refer to Parts List and Hardware List and ensure they are complete before you start assembling.
3. Place all wooden parts on a clean, flat and soft surface (e.g. carpet or rug) to prevent parts from getting scratched.
SAFETY PRECAUTION:
1. KEEP ALL HARDWARE PARTS OUT OF REACH OF CHILDREN.
2. DISPOSE PLASTIC PACKAGING MATERIAL IMMEDIATELY TO AVOID ANY RISK OF SUFFOCATION TO
CHILDREN AND ANIMALS.
TIPS FOR ASSEMBLY:
1. Allow ample room for assembly and in close proximity to where product will be placed.
2. Assemble the product on a surface that does not scratch or damage the exterior gloss and finish of the furniture.
3. Please check all of the parts and quantities are included before assembly. Contact customer service for missing parts.
4. Identify all of the parts, hardware and quantities required for each step.
5. During assembly, do not over-tighten any fittings as this may cause damage.
6. DO NOT USE POWER TOOLS TO ASSEMBLE THIS PRODUCT.
7. Always place the product on a flat surface.
8. Do not sit or stand on the partially assembled product; only use the product for which it is intended.
CARE AND MAINTENANCE
• Use a slightly damp cloth to clean the product. Do not use bleach or abrasive cleaning material.
• Check all the fittings periodically and re-tighten as necessary. Do not use the product if any of the parts is
damaged or broken.
• Never allow any kind of liquid to remain on your furniture. Absorption can cause wood to warp or delaminate.
• Do not place hot items (e.g. hot drinks) directly onto the wood surface.
• Do not drag and/or pull the furniture.
This product is for indoor and household-use only - not for commercial use.
ASSEMBLY INSTRUCTIONS
Lewis End Table ITEM# 72401WHT


  

       
      b 

      , 
 
  @     

  i    ' 
 
2/11

CAM-BOLT and CAM-LOCK
INSTRUCTIONS
Align the arrow on the Cam-lock to the Cam-
bolt head and insert the Cam-lock.
CAM-LOCK
� +
@®

; ;
CORRECT WRONG
CAM-BOLT
I nsert C am-bolt into the pre - drilled hole . U se a
P hillips S crewdriver to tighten until shoulder is flush
with the panel . S ee illustrations below .SHOULDER
X
Use a flat screwdriver to turn the Cam-Lock
clockwise one half a turn so it locks onto the head
of the Cam-lock. Turn only until it is snug – over-
tightening could damage Cam-lock or/and Cam-bolt
3/11

Parts & Assembly Oveiew
4/11

Parts List
ITEM DESCRIPTION PART QTY ITEM DESCRIPTION PART QTY
1   9   

2   10   
3   11  0
4   12  

·: 
5    13  
 
6  �: 
7  /
8   
5/11 Made In China

STEP 1
 
PART A

STEP2
  


X2
 
 
DO NOT USE POWER TOOLS
 
  &  S  &  3 
 &  3 

6/11

STEP3 H 4 pcs
H
H
!@
H
1. Insert Drawer Bottom Panel (11 ) by fitting (11) into the groo v e on Drawer Front & Side P anels.
2. Attach Drawer Back Panel (9) to Drawer Side Panel (12 & 13) by using Screw (H). ( Check
that Bottom Panel ( 11) fits into the groove on Back Panel before fastening )
STEP4 F 8 pcs
DO NOT USE POWER TOOLS



1. Install Part A of Metal Glide (G) to p ilot holes on drawer by using Screw (F).
7/11
METAL GLIDE
PART A


PARTS
F 
B  
DO NOT USE POWER TOOLS
 

 

 A  
DONOTUSEPOWERTOOLS
 

8/11
METAL
GLIDE

STEP? A  
B  
DO NOT USE POWER TOOLS

 
 
   
 
STEP8
 
 
 
9/11
A  
B  
DO NOT USE POWER TOOLS



STEP9 C  16 pcs
D  16 pcs
E b 1pc
E
DONOTUSEPOWERTOOL

1. Place one Leg (6) flat down as shown. Attach Connect Base (7) & Connect Base (8) to (6) by using Allen-
Head Bolt (D) and Lock Washer (C). Tighten (D) with Allen Wrench (E). Do not tighten completely until all of
the Bolts are in place.
2. I nstall the second Leg (6).
STEP10 C 4 pcs

D 4 pcs
E b 1pc
E 
D DONOTUSEPOWERTOOL
C
1. Place the sub-assembly completed in Step 8 bottom-side up (with Bottom Base (5) face up.)
2. Place Leg assembly from Step 9 bottom-side up and directly over Bottom Base (5) as shown.
3. Use Allen-Head Bolt (D) and Lock Washer (C) to attach Connect Base of Leg assembly to Bottom Base (5).
Tighten Bolt (D) by using Allen Wrench (E)
10/11

STEP 11
1. Insert drawers as shown.
Assembly of the desk is completed.
11/11