CN306
CN307
CN304
CN101 CN302
CN303
To CN303 To CN301
CN301
COM
C
9
8
7
Push down.
Cable
Conductor diameter:
ø 0.8 – 1.3 mm (AWG16 – 20),
Solid or Stranded wire
CN306
CN306
8 mm
[Connections]
5.2. External Dial Switch Connection
Connecting external switches such as
footswitches permits them to perform the
same operation as the dial keys "7," "8,"
"9," and "C".
An electrical current of 1 mA flows through
each contact.
Note
The cable length from the external switch
should not exceed 3 m.
2-pin removable terminal plug
(accessory,
factory-attached to the CN101)
CN101
1 2
Removable terminal plug
(accessory)
N-8031SB
Insert into the CN101's pin header.
Tighten
12
To N-8000EX/8010EX Exchange
16 lines
N-8031SB
[Connections]
5.1. Connection to the Exchange
Connect the CN101 terminal to the Exchange's
network connection terminal via the E-7000TB
Terminal Board.
For details, read the installation manual supplied
with the Exchange.
5.5. Status Indicator (LED) Connection
Use an LED with high brightness.
Connect a keyboard of
which circuit
configuration is as
shown in the figure.
An electrical current of
1 mA flows through
each contact.
5.3. Dial Key Connection
Hands-free
speaker
(accessory)
Hands-free
microphone
(accessory)
Note
For the CN304 connection, use the XHP-2 connector
manufactured by J.S.T. Mfg. Co., Ltd. or equivalent.
10
1
CN307
CN302
RS-191 rear
Ferrite clamp
(accessory)
Handset cable
1
2
Note
Run the cables along
the ferrite groove, and
clamp them.
5.4. RS-191 Connection
Connecting the RS-191 Option Handset to
the N-8031SB permits handset conversation.
Handset jumper
(accessory, factory-
attached to the
CN302)
Note
For the CN307 connection,
use the PHR-10 connector
manufactured by J.S.T.
Mfg. Co., Ltd. or equivalent.
(Internal circuit)
1 kΩ
CN304
Status indicator (LED)
2
1
Control IC
TTL level output
+5 V DC
FUNCTION
RESP.
CALL
HOLD
REDIAL
PTT C
0
TRANSFER
123
456
789
10987654321
Cable
Bared end: 7 mm
Conductor diameter:
ø0.4 –1.6 mm (AWG14 –26),
Solid or Stranded wire
Mini-clamp connector
(Supplied with the
Exchange)
Twisted pair cable
Note
Be sure to use the accessories.
Socket
Note
Though the socket on the PC
board is faced inside, you can
insert the handset jumper into
the socket from the side.
INSTALLATION MANUAL
MASTER STATION BOARD N-8031SB
1. GENERAL DESCRIPTION
The N-8031SB is a printed circuit board unit for the N-8031MS
Flush-Mount Hands-Free Master Station. You can make the
master station suitable for applications using the N-8031SB in
combination with the operation panel section to be prepared
separately.
3. SPECIFICATIONS
2. DIMENSIONAL DIAGRAM
Use the N-8000 software* to perform settings. Set up the same
items as performed to the N-8031MS since the N-8031SB is
handled as the N-8031MS on the software.
Key and status indicator operations are exactly the same as
those of the N-8031MS.
For settings, functions, and operations, read the descriptions
about the N-8031MS in the N-8000 Series instruction manual*.
* Included in the CD supplied with the N-8000EX/8010EX
Exchange.
4.1. Installation Precautions
•To prevent a malfunction or breakdown due to static
electricity, be sure to use a metal case or metal panel, and
screw the board at the indicated hole, so that the board is
electrically conducted to the case or panel.
4. MOUNTING TO A METAL CASE OR PANEL
•Cover the whole board with a case when installing.
4.2. Speaker and Microphone Installation
•To prevent acoustic feedback, attach the speaker and
microphone closely to the panel and position them at least
16cm away from each other's center as shown below.
Printed in Japan
133-06-273-90
20.6 Mounting
hole
6-ø3.5
1.6
70
52
521157
185
26
ø5790
[Side] [Hands-free
speaker]
[Hands-free
microphone]
2.1. N-8031SB 2.2. Accessory
[Front
(Component side)]
Unit: mm
CN306
CN307
CN304
CN101 CN302
CN303
CN301
8.5
ø9
195.5
57
N-8031SB N-8031SB Board fixing screw
Metal case or metal panel
Case or panel
Microphone
16 cm or more
Speaker
•Speaker opening ratio should be 36% (Example: ø4 mm x 61
holes) as a guide.
•Keep the board from coming in contact with the speaker to
avoid short-circuit between them.
•Make a microphone opening with the microphone rubber's
inside diameter (ø4.5 mm), and position the microphone in
the way that its center comes to the opening center.
•Never install them as shown below. Doing so may cause the
speaker sound to enter the microphone.
Case or panel
Microphone
Speaker
Case or panel
Microphone
Sound enters
the microphone.
Sound enters the microphone.
Speaker
5. CONNECTIONS
48 V DC (supplied from the N-8000EX/8010EX
IP Intercom Exchange)
1.8 W (rated), 2.4 W (max.)
Non-polar one pair stranded wire system
2-wire 160 kbps echo canceller transmission
system
Under 0 dB*
Hands-free conversation
(Handset conversation can be established in
conjunction with the RS-191.)
300 –7,000 Hz
Max. 1,500 m (ø0.65 mm, Loop resistance
170 Ωor less)
Speaker (accessory):
5.7 cm cone-type, 0.6 W, 8 Ω
Microphone (accessory):
Omni-directional electret condenser microphone
Pin header (2 pins)
Power Source
Power Consumption
Wiring Method
Transmission System
Signal Level
Speech Method
Audio Frequency
Range
Transmission Range
Hands-Free
Line Connection
Terminal
Solderless connector (2 pins, male),
voltage: 5 V, maximum load current: 5 mA
Solderless connector (10 pins, male), open
voltage: 3.3 V DC, short-circuit current: 1 mA,
screwless connector (5 pins)
No-voltage make contact input, open voltage:
5 V DC, screwless connector (5 pins)
0°C to +40°C
Under 90% RH (no condensation)
70 (w) x 185 (h) x 20.6 (d) mm
205 g (including accessories)
Removable terminal plug (2 pins, preinstalled on
the unit) ... 1, Handset jumper (8 pins,
preinstalled on the unit) ... 1, Ferrite clamp ... 1,
Hands-free speaker (with connection cord) ... 1,
Hands-free microphone (with connection cord)
... 1
Status Indicator LED
Connecting Terminal
Dial Input
External Dial Input
Operating Temperature
Operating Humidity
Dimensions
Weight
Accessories
* 0 dB = 1 V
Note: The design and specifications are subject to change without notice for improvement.
