Toa EM-600 User manual

OPERATING INSTRUCTIONS
日本語の取扱説明書は裏面をご覧ください。
1. SAFETY PRECAUTIONS
• Before installation or use, be sure to carefully read
all the instructions in this section for correct and
safe operation.
• Be sure to follow all the precautionary instructions
in this section, which contain important warnings
and/or cautions regarding safety.
• After reading, keep this manual handy for future
reference.
• Install the unit only in a location that can
structurally support the weight of the unit and the
mounting components. Doing otherwise may result
in the unit falling down and causing personal injury
and/or property damage.
• Do not expose the unit to rain or an environment
where it may be splashed by water or other liquids,
as doing so may result in electric shock.
• Do not lay the connection cable where it can be
walked on or tripped over, causing personal injury.
2. GENERAL DESCRIPTION
The EM-600 is an omnidirectional condenser microphone
of only 28 mm (1.1") in diameter. It can be flush-mounted
into a ceiling, wall, or desk, making it unobtrusive.
3. FEATURES
• Realizes optimum acoustic characteristics suitable for
sound pick-up when flush-mounted into a ceiling or wall.
• Provides clear, easy-to-listen-to, high-quality sound.
4. HANDLING PRECAUTIONS
• Be sure to turn off the phantom power switch on the
equipment that the unit is connected to before
connecting or disconnecting the unit. As doing otherwise
may cause loud noise or damage to the unit or
connected equipment.
• Avoid installing the unit in humid or dusty locations, in
locations exposed to the direct sunlight, near the
heaters, or in locations generating sooty smoke or steam
as doing otherwise may result in unit failure.
• Take care not to drop the unit onto the floor nor bump it
against a hard object as the unit could fail.
• Avoid using a mobile telephone near the microphone in
use. Noise could be picked up.
• To clean, be sure to first disconnect the connection
cable, then wipe with a dry cloth. When the unit gets very
dirty, use a cloth damped in a neutral cleanser. Never
use benzene, thinner, alcohol, or chemically-treated
cleaning cloth because such volatile liquids could deform
or discolor the unit.
Thank you for purchasing TOA's Flush-mount Boundary Microphone.
Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.
EM-600FLUSH-MOUNT BOUNDARY
MICROPHONE
CAUTION
Indicates a potentially hazardous situation which,
if mishandled, could result in moderate or minor
personal injury, and/or property damage.
5. SPECIFICATIONS
Note: The design and specifications are subject to change
without notice for improvement.
Element Electret condenser
Polar Pattern Omnidirectional
Rated Impedance 120 Ω, balanced
Rated Sensitivity –36 dB (0 dB = 1 V/Pa, 1 kHz)
Frequency Response 30 Hz – 20 kHz
Phantom Power 9 – 52 V DC
Output Connector XLR-3-12 or equivalent
Finish Main body:
Steel, white, semi-gloss, paint
Head:
Galvanized steel wire, white,
semi-gloss, paint
Dimensions ø28 x 68 mm (ø1.1" x 2.68")
Weight 85 g (0.19 lb)
Accessories Rubber isolation ring ........ 2
Nut (for M20) .................... 1

133-04-190-50
URL: http://www.toa.jp/
6. COMPONENTS
Microphone body ........ 1 Rubber isolation ring ........ 2
Nut (for M20) ...... 1
7. INSTALLATION
The figure below shows an example when flush-mounting
the unit into a ceiling. Similarly, it can be flush-mounted
into a wall or desk.
Nut
ø24* (0.94)
Microphone
[Installation completion drawing]
* Recommended mounting
hole diameter
Unit: mm (in)
Connect with XLR-3-11 or equivalent
(separately prepared).
Ceiling
Rubber
isolation ring
Rubber
isolation ring
9 – 40 (0.35 – 1.57) 68 (2.68)
10 (0.39)
Microphone
8. CIRCUIT DIAGRAM
Body earth
Cold
Hot
3
2
Shield
1
Filter circuit
Power circuit
9. DIRECTIVITY CHARACTERISTICS
5
0
90°
120°
150°
180°
240°
270°
210°
300°
330°
0°
30°
60°
- 5
- 10
- 15
- 20
1 kHz
4 kHz
10. FREQUENCY RESPONSE
Frequency
Response
20
- 30
- 20
- 10
- 0
10
20
50 100 500 1 k 5 k 10 k 20 k
[Hz]
[dB]
Traceability Information for Europe (EMC directive 2004/108/EC)
Manufacturer:
TOA Corporation
7-2-1, Minatojima Nakamachi, Chuo-ku, Kobe, Hyogo, Japan
Authorized representative:
TOA Electronics Europe GmbH
Suederstrasse 282, 20537 Hamburg, Germany