TOP racing Photon EX User manual

EQUIPMENT RECOMMENDED (NOT INCLUDED)
Radio Transmitter•
Radio receiver•
Batteries for Transmitter•
Electronic Speed Control•
Steering Servo•
Brushless Motor System•
Pinion Gear (64 Pitch)•
7.4V Li-Po Pack•
190mm Body Shell•
Touring Car Wheels, Tires and Inserts•
TOOLS RECOMMENDED (NOT INCLUDED)
1.5mm, 2.0mm, 3.0mm Allen Wrench•
5.0mm, 5.5mm & 7.0mm Hex Socket Wrench•
Modelers Craft Knife•
Small Cross Head Screw Driver•
Turnbuckle Wrench•
Calipers/Ruler•
Camber Gauge•
Battery Strapping Tape•
Instant Glue/Thread Lock•
Shock Oil•
Gear, Diff. Grease, Joint Grease, Gear Diff Oil•
Paint (for Bodyshell)•
NOTE:
The Photon EX chassis uses the best available components. All•
replacement parts can be purchased from your local hobby or model
shop.
There are 2 versions of the Photon EX - Standard Chassis and Stiff•
Chassis.Askyoulocalhobbyshopsforconrmingwhichkityouwould
like to purchase.
This instruction manual contains a blank setup sheet for your own setup•
record.
Enjoy building and driving your Photon EX!!
Do not use your model:•
Near real cars, animals, or people that are unaware that an RC car1.
is being driven.
In places where children and people gather2.
In limited indoor spaces3.
In wet conditions4.
In the street5.
In areas where loud noises can disturb others such as hospitals and6.
residential areas
At night or anytime your line of sight to the model may be obstructed7.
or impaired in any way.
To prevent any serious personal injury and/or damage to property, please
be responsible when operating all remote controlled models.
ELECTRICAL PRECAUTIONS
Insulate any exposed electrical wiring (using heat shrink tubing or•
electrical tape) to prevent dangerous short circuits. Take maximum
care in wiring, connecting and insulating cables. Make sure cables
are always connected securely. Check connectors for if they become
loose. And if so, reconnect them securely. Never use R/C models with
damaged wires. A damaged wire is extremely dangerous, and can
causeshort-circuitsresultinginre.
Low battery power will result in loss of control. Loss of control can•
occur due to a weak battery in either the transmitter or the receiver
Weak running battery may also result in an out of control car if your
car’s receiver power is supplied by the running battery. Stop operation
immediately if the car starts to slow down.
When not using RC model, always disconnect and remove battery.•
Do not disassemble battery or cut battery cables. If the running•
battery short-circuits, approximately 300W of electrical power can be
discharged,leadingtoreorburns.Neverdisassemblebatteryorcut
battery cables.
Use a recommended charger for the receiver and transmitter batteries•
and follow the instructions correctly. Over-charging, incorrect charging,
or using inferior chargers can cause the batteries to become dangerously
hot. Recharge battery when necessary. Continual recharging may
damage battery and, in the worst case, could build up heat leading to
re. If battery becomes extremely hot during recharging, please ask
your local hobby shop for check and/or repair and/or replacement.
Regularly check the charger for potential hazards such as damage to the•
cable,plug,casingorotherdefects.Ensurethatanydamageisrectied
before using the charger again. Modifying the charger may cause short-
circuit or overcharging leading to a serious accident. Therefore do not
modify the charger.
Alwaysunplugchargerwhenrechargingisnished.•
Do not recharge battery while battery is still warm. After use, battery•
retains heat. Wait until it cools down before charging.
Do not allow any metal part to short circuit the receiver batteries or other•
electrical/electronic device on the model.
Immediately stop running if your RC model gets wet as may cause short•
circuit.
Pleasedisposeofbatteriesresponsibly.Neverputbatteriesintore.•
BEFORE YOU START
The Photon EX is a professional 1/10 scale touring car and should be
built only by persons aged 16 years or older with previous experience
building and operating R/C model cars. This is not a toy and is not
intended for use by beginners or by children without direct supervision of a
responsible, knowledgeable adult. Read the instruction manual carefully
before building.
T.O.P. Racing shall not be liable for any loss, injury or damages, whether
direct, indirect, special, incidental, or consequential, arising from the use,
misuse, or abuse of this product and/or any product or accessory required
to operate this product.
GENERAL PRECAUTIONS
This product is not suitable for children under 16 years of age without•
the direct supervision of a knowledgeable adult.
Assemble this kit only in places away from the reach of small children.•
First-time builders and users should seek advice from people who have•
building experience in order to assemble the model correctly and to
allow the model to reach its performance potential.
Exercise care when using tools and sharp instruments.•
Take care when building, as some parts may have sharp edges.•
Keep small parts out of reach of small children. Children must not•
be allowed to put any parts in their mouth, or pull vinyl bag over their
head.
Immediately after using your model, do not touch equipment on the•
model such as the motor and speed controller, because they generate
high temperatures. You may seriously burn yourself by touching them.
Follow the operating instructions for the radio equipment at all times.•
Donotputngersoranyobjectsinsiderotatingandmovingparts,as•
thismaycausedamageorseriousinjuryasyournger,hair,clothes,
etc. may get caught.
Be sure that your operating frequency is clear before turning on or running•
your model, and never share the same frequency with somebody else at
the same time. Ensure that others are aware of the operating frequency
you are using and when you are using it.
Always turn on your transmitter before turning on the receiver in the car.•
Always turn off the receiver before turning off your transmitter.
Keep the wheels of the model off the ground when checking the•
operation of the radio equipment.
Disconnect the battery pack before storing your model.•
To prevent any serious personal injury and/or damage to property, be•
responsible when operating all remote controlled models.
The model car is not intended for use on public places and roads or•
areas where its operation can conict with or disrupt pedestrian or
vehiculartrafc.
INTRODUCTION
Page 1

ご案内
使 用 前 に:
Photon EXはハイエンド向け1/10スケールツーリングカーです。
すでに組立てや、ラジコンカー操作の経験を積んだ16歳以上のユーザーに
適していま
す。玩具ではありませんので、初心者や責任ある大人の監視のない子供だけで
の使用は
控えて下 い。
T.O.P Racingは、直接、間接、特別、偶発的、結果的あらゆる使用上、又は誤
使用、
不正使用により発生する損害、怪我、ダメージ等の責任は負いません。
注意:
* 本製品は、16歳以下の子供のみでの使用には適しておりません。必ず、
経験のある大人の監視の元で使用下さい。
* 組立ては、小さなお子様の手の届かない場所で行って下さい。
* 初めて組立てられる方の場合、経験者のアドバイスを受けながら、本来の
性能が発揮出来るように正しく組立てを行うようにして下さい。工具、鋭
利な器具などは注意し
て使用下さい。
* 組立ての際、部品によっては端が鋭くなってますので、注意して下さい。
* 小さな部品は、小さなお子様の手の届かない場所に保管して下さい。小さ
なお子様が部品を飲み込んだり、ビニール袋を頭から冠ったりしないよう
注意下さい。
* 使用後直後は、大変高温度になってますので、モーター、スピードコントロ
ーラー等に手を触れぬようして下さい。もし触れると火傷の恐れがありま
す。
* 送信機の操作指示には常に従うよう心がけで下さい。
* 回転中の稼働している部分には決して指や、異物を入れないで下さい。
指、髪の毛、衣服、他にダメージや怪我の恐れがあります。
* 操作する際の周波数は、使用する前に必ず確認下さい。同時に他の方と
同じ周波数を使用しないように注意して下さい。
* 常に送信機のスイッチを先に入れ、その後で車に搭載のレシーバーのスイ
ッチを入れて下さい。スイッチを切る場合は、先にレシーバーのスイッチを
切り、その後に送信機のスイッチを切って下さい。
* プロポ装置の作動チェックの際は、ホイル部を地面から離して下さい。
* 車を保管する場合は、バッテリーパックを外して下さい。
* 怪我や、物への損害を避けるためにも、操作中は充分に責任を自覚して下
さい。使用する場合、公共の場所、公道などの歩行者や、乗物等と衝突す
る恐れのある場 所では使用しないで下さい。下記の使用はしないで
下さい。
必要な装備等(キット付属してません)
* 送信機
* 受信機
* 送信機用バッテリー
* スピードコントローラー(ESC)
* ステアリング サーボ
* ブラシレスモ ー ターシステム
* ピニオンギア(64ピッチ)
* 7.4V リポパック
* 190 mm ボディーシェル
* ツ ー リ ン グ カ ー ホ イ ル 、タ イ ヤ 、イ ン サ ー ト
必要な工具(付属してません)
1.5 mm, 2.0 mm, 3.0 mm 六角レンチ
5.0 mm, 5.5 mm, 7.0 mm 六角ソケットレンチモデラー用クラフトナイフ
ターンバックル レンチ
小型クロスヘッドスクリュードライバー
キャンバー ゲージ
バッテリー ストラップテープ
瞬間接着剤/ネジ止め
ショーックオイル
ギアデフグリース、ジョイントグリース、ギアデフオイル
塗料(ボディー用)
注意:
* Photon シャーシはベストな部品を使用します。交換部品はお近くの模型
店
等、弊社製品取扱い店でお求め下さい。
* こ の 取 説 マ ニ ュ ア ル に は 、セ ッ ト ア ッ プ シ ー ト が 付 属 し て ま す の で 、セ ッ ト
アップ記録下さい。
* 下記の使用はしないで下さい。
1.ラジコン操作に気づいてない自動車、動物、人間の近くでの使用
2.子供、又は集団で集まっている場所
3.狭い室内スペース
4.濡れた場所
5.公道
6.騒音によって迷惑を掛ける病院、居住地など
7.夜間や、又は視界が妨害されたり、損なわれる場合
身体、物への障害を防ぐために、すべてのリモコンモデルの操作に
責任を持って下さい。
電気系統に対しての注意:
* 露出した電気配線は、必ず絶縁しショートを防いで下さい。(ヒート
シンクチューブ、又は電気テープ等で絶縁)配線、接続、ケーブルの
絶縁等には充分な注意をして下さい。ケーブルが常にしっかり接続さ
れている事を確認して下さい。コネクターの緩みをチェックし、もし
緩んでいれば、再度接続をし、しっかりと接続して下さい。
ダメージのあるケーブルは決して使用しないで下さい、大変危険で、
火災に至るショートを起こす可能性があります。
* 低いバッテリーパワーはコントロールロスを招きます。
送信機や、受信機のパワーが落ちると制御が効かなくなります。車が
減速し始めましたら、すぐに操作中止下さい。
* 操作しない場合は、バッテリーを外して下さい。
* バッテリーを分解したり、バッテリーケーブルを切断したりしないで下さ
い。もし駆動中のバッテリーがショートするとおよそ300Wの電力が放電
され火災や、爆発を誘発します。
* 受信機、送信機用バッテリーの充電には、推奨された充電器を使用下さ
い。必
ず、充電器の取説マニュアルに従って正しく使用下さい。
過充電、不正な充電、又は不良充電器の使用で高熱発生し、危険です。連
続し再充電をすると、バッテリーを傷め、最悪の場合には異常に高温にな
り、火災を引き起こします。もし、お使いのバッテリーが再充電中、異常に
高温度にある場合はお買求めのショップに相談、確認をし修理、交換等し
て下さい。
* 定期的に充電器のチェック、例えばケーブル、プラグ、ケース、他の損傷な
どを事前チェックし安全性を確認してから使用するよう心がけて下さい。
充電器の改造は、ショート、過充電など危険な事態を招きますので決して
行わないで下さい。
* 充電終了後は、常に充電器からプラグを外して下さい。
* バッテリーがまだ暖まっている場合には、再充電をしないで下さい。
使用後、バッテリーは熱を持っていますので、充分温度が下がるまで充電
を控えて下さい。
* 受信機用バッテリーや、他の電気系統部をショートさせるような金属部
品を接触させないで下さい。
* 車が濡れた場合、速やかに走行を中止し、ショートしないようにして下さ
い。
* バッテリーの廃棄には責任を持ち、決して火の中に捨てないよう注意して
下さい。 Page 2

x 2 PA-HSS101
Hard Shim
シム
5 x 15 x 0.3mm
x 1 PO-MGAS03
Small Bevel Gear Holder
スモール ベベルギアホルダー
x 2 AW-S150RD
Collar
スペーサー
3 x 5.5 x 1.5mm
x 1 TC-PXCH018RD
Bell Crank Bridge
ベ ル クラン クブ リッジ
x 1 TC-PMJS03
40T Flange - One-way/Spool
40T フランジ-ワンウェイ/スプール
x 1 TC-PMJS03
40T Spool
40T スプール
x 2 TC-PML104
Bearing Cam
ベアリングカム
x 2 PP-GDRS01
Silicone O-Ring
シリコン Oリング
5mm
BAG C
BAG A
BAG CBAG B
x 2 PA-SC0312
Countersunk Stainless Steel Hex Screw
皿 ステンレス 六 角ビ ス
M3 x 12 mm
x 2 PA-SB1510
Bearing
ベアリング
10 x 15 x 4mm
x 2 PA-SB1510
Bearing
ベアリング
10 x 15 x 4mm
x 2 PO-DT1009RD
Spacer
スペーサー
12 x 10 x 0.9t
x 4 PA-CM2508BK
Countersunk Screw
皿ビス
M2.5 x 8mm x 1 PP-GDRS01
Silicone O-Ring
シリコン Oリング
24mm
x 1 PO-MGAS02
40T Gear Diff Pulley
40T ギアデフプーリー
x 1 TC-PXCH019
Center Shaft Steel
セ ンタ ー シ ャフトス チ ー ル
x 4 PA-SB1005
Bearing
ベアリング
5 x 10 x 4mm
x 2 TC-PMLS02
Center Shaft Spacer
センターシャフトスペーサー
PA-SCM205BK
Chess Head Screw
チェスヘッドネジ
x 4 M2 x 5mm
x 1 SG-K48084
Spur Gear
スパーギア
48P 84T
TC-PMLS02 x 2
20T Pulley Set
20T プーリーセット
x 3 PA-SS0308BK
Set Screw
イモネジ
M3 x 8mm
x 2 PA-CM0308BK
Countersunk Screw
皿ビス
M3 x 8mm
x 2 PA-CM0306BK
Countersunk Screw
皿ビス
M3 x 6mm
x 6 PA-100305
Shim 3 x 5 x 0.3mm
シム 3 x 5 x 0.3mm
x 2 PA-100507
Shim 5 x 7 x 0.2mm
シム 5 x 7 x 0.2mm
x 2 AW-BW31RD
Small M3 Bevel Washer
スモール M3べベルワッシャー
x 2 TC-PXCH017RD
Bell Crank Arm
ベルクランクアーム
x 1 TC-PXCH012RD
Motor Plate
モ ー タ ープレ ート
BAG D
x 1 TC-PXCH013RD
Mount Plate
マ ウ ントプ レ ー ト
x 2 TC-PXCH016RD
Steering Post
ステアリング ポスト
x 1 TC-PXCH014RD
Motor Plate Support
モータープレートサポート
x 14 PA-CM0306BK
Countersunk Screw
皿ビス
M3 x 6mm
x 4 TC-PXCH011RD
Bulkhead
バクル ヘッド
x 2 PA-SB0805
Bearing
ベアリング
5 x 8 x 2.5mm
x 2 AW-M100RD
Ultra Wide Collar
ウルトラワイドカラ ー
3mm x 1.0t
x 3 PA-HBS003
5.3mm Ball
5.3mm ボール
x 2 PO-DT0018H
Gear Diff Outdrive
ギアデフアウトドライブ
x 1 PO-PDT101
Gear Diff Case
ギアデフケース
x 4 PA-HSS101
Hard Shim
シム
3.5 x 10 x 0.3mm
x 2 PO-MGBS01
Large Bevel Gear
ラージ べベルギア
x 2 PA-SP0208
Steel Pin
スチールピン
2 x 8 mm
x 2 PA-101215
Shim
シム
12 x 15 x 0.3mm
x 4 PO-MGBS01
Small Bevel Gear
スモール べベルギア
x 2 PO-DT1009RD
Spacer
スペーサー
10 x 12 x 2mm
x 2 TC-PML104
Bearing Cam
ベアリングカム
x 2 PO-PDT003
Spool Steel Outdriver
スプールスチールアウトドライバー
Page 3

x 1 TC-PDT008BL
Front Belt
フロントベ ルト
x 2 TC-PXSU001RD
Suspension Mount Holder FF/RR
サスペンションマウントホルダー FF/RR
x 16 PA-CM0308BK
Countersunk Screw
皿ビス
M3 x 8mm
x 12 AW-M050RD
Ultra Wide Collar
ウルトラワイドカラ ー
3mm x 0.5t
BAG D BAG F
BAG G
BAG G BAG G
BAG H
BAG E
x 1 PA-LN00M3
M3 Steel Nylon Lock Nut
M3 スチールナイロンロックナット
x 1 PA-SF0330
Stainless Steel Button Head Screw
ステンレスボ タンヘッドネジ
M3 x 30mm
x 1 TC-PDT006BL
Rear Belt
リアベルト
x 4 AW-S100RD
Collar
カラー
3 x 5.5 x 1mm
x 4 PA-SS0308BK
Set Screw
イモネジ
M3 x 8mm
x 4 PA-HBS003
5.3mm Ball
5.3 mmボール
x 4 TC-PXCH015RD
Alloy Camber Link Plate
アロ イキャンバ ー リンクプレ ート
x 20 PA-BM0306BK
Buttom Head Screw
ボタンヘッドネジ
M3 x 6mm
x 4 PO-DT0011
Universal Pin
ユニバーサル ピン
2 x 10mm
x 2 PO-SDT009RD
46mm Universal Bone
46 mm ユニバーサルボーン
x 2 PO-SDT026RD
44.5mm Universal Bone
44.5 mm ユニバーサルボーン
x 4 PO-SDT019
Universal Insert
ユニバーサル インサート
x 4 PO-SDT018
Universal Axle
ユニバー サル アクスル
x 4 PA-SS0303BK
Set Screw
イモネジ
M3 x 3mm
x 4 PO-DT1004RD
M2 Wheel Hub Screw
M2 ホイルハブネジ
x 2 PA-HBS003
5.3mm Ball
5.3 mm ボール
x 4 PO-DT1004RD
5.2mm Wheel Hub
5.2 mm ホイルハブ
x 2 PA-SS0310BK
Set Screw
イモネジ
M3 x 10mm
x 4 PO-DT1004RD
Steel Pin
スチールピン
2 x 10mm
x 2 PO-DT0006
Dog Bone C Drive
ドッグ ボーンCドライブ
x 8 PA-SB1005
Bearing
ベアリング
5 x 10 x 4mm
x 2 TC-PMGS01
Steering Block
ステアリングブロック
x 2 AW-S200RD
Collar
カラー
3 x 5.5 x 2mm
x 2 TC-PMGS01
Rear Hub Carrier
リアハブキャリア
x 1 TC-PMFS01
Right Castor Block - 4
右キャスターブロック - 4
TC-PMFS01 x 1
Left Castor Block - 4
左キャスターブロック - 4
x 2 PA-CM0310BK
Countersunk Screw
皿ビス
M3 x 10mm
x 2 PA-HBS003
5.3mm Ball
5.3 mm ボール
x 2 PA-SS0308BK
Set Screw
イモネジ
M3 x 8mm
x 2 PA-HBS0508
5.3mm Steel Ball Head Screw
5.3 mmスチールボールヘッドネジ
x 4 TC-PMFS01
Castor Block Insert
キ ャス タ ーブ ロック イン サ ー ト
x 2 TC-PMES01
Front Suspension Arm
フロントサスペンションアーム
TC-PMES01 x 2
Rear Suspension Arm
リアサスペンションアーム
x 4 TC-PSU001
Hinge Pin
ヒンジピン
x 4 PA-SS0306BK
Set Screw
イモネジ
M3 x 6mm
x 4 PA-SS0308BK
Set Screw
イモネジ
M3 x 8mm
x 4 TC-PXSU002RD
Suspension Mount Holder FR/RF
サスペンションマウントホルダーFR/RF
Page 4

x 4 TC-PSH002
Shock Bladder
ショックブラダー
x 4 TC-PSUS01
Collar
カラー
3 x 7 x 0.4mm
x 4 TC-PSU002
Hinge Pin 3 x 51mm
ヒンジピン 3 x 51mm
x 2 AW-S050RD
Collar
カラー
3 x 5.5 x 0.5mm
x 4 AW-S150RD
Collar
カラー
3 x 5.5 x 1.5mm
x 2 AW-S250RD
Collar
カラー
3 x 5.5 x 2.5mm
x 8 TC-PXSU003
Steel Suspension Mount Insert
スチールサスペンションマウントインサート
x 6 PA-BM0315BK Button Head Screw
ボタンヘッドネジ
M3 x 15mm
x 2 PA-BM0318BK Button Head Screw
ボタンヘッドネジ
M3 x 18mm
BAG H BAG i BAG i (x2)
x 2 AW-M200RD
Ultra Wide Collar
ウルトラワイドカラ ー
3 x 7 x 2mm
x 4 AW-M100RD
Ultra Wide Collar
ウルトラワイドカラ ー
3 x 7 x 1mm
x 1 TC-PXCHS006
Front Shock Tower
フロントショックタワー
x 1 TC-PXCHS007
Rear Shock Tower
リアショックタワー
x 4 PA-CM0306BK
Countersunk Screw
皿ビス
M3 x 6mm
x 2 TC-PMHS01
Ball Cup
ボ ー ル カップ
14.5mm
x 2 TC-PSU003RD
Threaded Sway Bar Adjuster
スレッド スウェ イバ ーア ジ ャスタ ー
x 2 TC-PMMS02
Ball Cup
ボ ー ル カップ
10.5mm
x 2 PA-HBS0508
Ball Stud (Steel)
ボールスタッド(スチール)
5.3 x 8mm
x 5 PA-SS0303BK
Collar
カラー
3 x 7 x 0.4mm
x 1 AW-ST02RD
Stopper
ストッパー
x 2 PA-BM0310BK
Button Head Screw
ボタンヘッドネジ
M3 x 10mm
x 1 TC-PSB012
Stabilizer Bar
スタビライザーバー
1.2mm
x 8 TC-PMMS03
Suspension Mount H
サスペンションマウント H x 1 TC-PSB014
Stabilizer Bar
スタビライザーバー
1.4mm
BAG i
x 4 TC-PMRS01 Shock Piston
ショックピ ストン
1.2mm - 2 hole
x 4 TC-PMRS01 Shock Piston
ショックピ ストン
1.2mm - 3 hole
x 4 TC-PMRS01 Shock Piston
ショックピ ストン
1.0mm - 2 hole
x 4 TC-PMRS01 Shock Piston
ショックピ ストン
1.0mm - 3 hole
x 4 PO-PSH002
Teflon Shock Guide
テフロンショックガ イド
BAG i
x 1 MC-MLK001 Tie Rod (Steel)
タ イ ロ ッ ド( ス チ ー ル )
M3 x 15mm
x 6 TC-PSU005 Tie Rod (Steel)
タ イ ロ ッ ド( ス チ ー ル )
M3 x 30mm
x 4 TC-PMHS02 Ball Cup
ボ ー ル カップ
18.5mm
x 10 TC-PMHS01 Ball Cup
ボ ー ル カップ
14.5mm
BAG J
BAG J BAG J BAG J
x 4 PP-010320
OIL MIXED O-RING FOR DAMPERS 30
オイルミックスO-リング ダンパー30用
x 4 TC-PSH101RD
Spring Adjuster Nut O-Ring
スプリングアジャスターナット O-リング
x 4 TC-PSH101RD
Shock Spring Adjuster
シ ョッ クスプ リン グ ア ジ ャス タ ー
x 4 TC-PSH101RD
Shock Body
ショックボディー
x 4 TC-PSH101RD
Shock Cap
ショックトップ キ ャップ
x 4 TC-PSH101RD
Shock Bottom
ショックボトム
BAG J
x 8 PA-ER0020
2mm E-Clip
2mm E - クリップ
x 8 PA-HBS003
Ball (Steel)
E- クリップ
5.3mm
x 4 PA-BM0306BK
Button Head Screw
ボタンヘッドネジ
M3 x 6mm
x 4 TC-PSH007
Shock Shaft
ショックシ ャフト
x 4 TC-PMMS02
Ball Cup
ボ ー ル カップ
10.5mm
x 4 TC-PMMS02
Damper Top Ring (Shock Top)
ダ ンパ ー トップ リン グ( ショックトップ )
x 4 TC-PMMS02
Damper Spring Holder
ダンパースプリングホルダー
x 8 TC-PMMS02
Spring Adjust Nut Spacer
ス プリン グ ア ジ ャストナ ットス ペ ー サ
14mm
x 4 TC-MAAS01
Stabilizer Mount L
スタビライザーマウント L
x 4 TC-MAAS01
Stabilizer Mount S
スタビライザーマウント S
Page 5

x 2 PS-TR15575
Shock Spring
ショックスプリング
14 x 1.5 x 5.75
x 2 PS-TR15650
Shock Spring
ショックスプリング
14 x 1.5 x 6.50
x 4 PA-BM0306BK
Button Head Screw
ボタンヘッドネジ
M3 x 6mm
x 1 TC-PMQS01
Upper Bumper
アッパーバンパー
x 2 SK-CH1001
Bumper Standoff
バンパースタンドオフ
x 2 SK-CH1001
Front Body Post
フロントボディポスト
x 2 SK-CH1001
Rear Body Post
リアボディーポスト
x 1 TC-PMQS01
Lower Bumper
ローアーバンパー
x 4 SK-CH1001
Body Holder
ボディーホルダー
x 8 PA-BPS3SV
Body Clip
ボ ディ ー クリップ
x 2 PA-BM0310BK
Button Head Screw
ボタンヘッドネジ
M3 x 10mm
x 5 PA-CM0308BK
Countersunk Screw
皿ビス
M3 x 8mm
x 3 PA-FN00M3
M3 Nut
M3 ナット
TC-PXCHC009 x 2
Lipo Battery Mount Plate B
リ ポ バ ッ テ リ ー マ ウ ン トプ レ ー ト B
x 8 PA-SP0307
Flat Washer
フラットワッシャー
M3 x 7 x 0.5
x 4 AW-M100RD
Ultra Wide Collar
ウルトラワイドカラ ー
3 x 7 x 1mm
x 2 PA-CM0310BK
Countersunk Screw
皿ビス
M3 x 10mm
x 4 PA-CM0314BK
Countersunk Screw
皿ビス
M3 x 14mm
x 6 PA-LN00M3
M3 Lock Nut
M3 ロックナット
x 2 TC-PXCHC008
Lipo Battery Mount Plate A
リ ポ バ ッ テ リ ー マ ウ ン トプ レ ー ト A
x 1 TC-PXCHC010
Lipo Battery Mount Plate Center
リ ポ バ ッ テ リ ー マ ウ ン トプ レ ー ト セ ン タ ー
x 1 TC-PMPS01
Servo Arm
サーボアーム
Futaba
x 1 TC-PMPS01
Servo Arm
サーボアーム
Hitec
x 1 TC-PMPS01
Servo Arm
サーボアーム
KO / Sanwa
x 1 PA-HBS003
5.3mm Ball (Steel)
5.3mm ボール(スチール)
x 1 PA-SS0310BK
Set Screw
イモネジ
M3 x 10mm
x 1 AW-M300RD
Ultra Wide Collar
ウルトラワイドカラ ー
3 x 7 x 3.0mm
x 1 PA-BM0306BK
Button Head Screw
ボタンヘッドネジ
M3 x 6mm
x 2 PA-BM0308BK
Button Head Screw
ボタンヘッドネジ
M3 x 8mm
x 2 TC-PMPS01
Servo Mount
サー ボマウント
Large
x 2 TC-PMPS01
Servo Mount
サー ボマウント
Small
x 2 PA-CM0306BK
Countersunk Screw
皿ビス
M3 x 6mm
x 2 PA-SP0307
Flat Washer
フラットワッシャー
M3 x 7 x 0.5
x 1 PA-AT0001 Antenna アンテナ
x 1 PA-AP0001
Antenna Post
アンテナポスト
x 1 PA-ATC001
Antenna Cap
アンテナキャップ
x 1 PA-CM0306BK
Countersunk Screw
皿ビス
M3 x 6mm
x 2 PA-CM0310BK
Countersunk Screw
皿ビス
M3 x 10mm
x 2 AW-BW31RD
Small Bevel Washer
スモ ール べ ベルワッシャー
x 2 PA-OR1004
O-Ring 2 x 4
O-リング 2 x 4
x 4 PA-SNF4BK
M4 Steel Serrated Wheel Nut
M4 スチールセレートホイルナット
BAG L
BAG L
BAG M BAG M
BAG K
BAG K
BAG J
Page 6

x 1 PT-NTW001
Rod Wrench
ロッドレンチ
x 1 TC-PXCHC001
Chassis シャーシ
Standard 標準
x 1 TC-PXCHC004
Upper Deck アッパーデッキ
Standard 標準
x 1 TC-PXCHC005
Upper Deck アッパーデッキ
Stiff ス ティッフ
x 1 TC-PXCHS002
Chassis シャーシ
Stiff ス ティッフ
x 1 TC-PCH20H
Foam Bumper
フォームバンパー
Page 7

x 4 PA-HSS101
Shim
シム
3.5 x 10 x 0.3mm
SPOOL FINISHED
ベアリング 10 x 15 x 4mm
Bearing 10 x 15 x 4mm
シム 12 x 15 x 0.3mm
Shim 12 x 15 x 0.3mm
Countersunk Screw
皿ビス
M2.5 x 8mm
Silicone O-Ring
シリコン Oリング
24mm
Countersunk Stainless Steel Hex Screw
皿 ステンレス 六 角ビ ス
M3 x 12mm
Small Bevel Gear
スモールべベルギア
Hard Shim Small
ハードシム スモ ール
Hard Shim Small
ハードシム スモ ール
Hard Shim Small
ハードシム スモ ール
Small Bevel Gear
スモールべベルギア
Bearing
ベアリング
10 x 15 x 4mm
Bearing
ベアリング
10 x 15 x 4mm
Spacer
スペーサー
12 x 10 x 0.9mm
Spacer
スペーサー
10 x 12 x 2mm
Spacer
スペーサー
10 x 12 x 2mm
Spacer
スペーサー
12 x 10 x 0.9mm
*NOTE :
DO NOT ll the diff oil to the top of the diff Holder
デフホルダーの上限までデフオイルを入れないで下さい。
SPOOL & GEAR DIFFERENTIAL \ スプール&ギアデフ
Silicone O-Ring
シリコン Oリング
5mm
Shim
シム
5 x 9 x 0.1mm
Large Bevel Gear
ラージべベルギア
Hard Shim Large
ハードシム ラージ
*NOTE: Add gear diff grease here (Not Included)
Gear diff grease is for leakage prevention
注意: デフギア用グリスを付ける (別売)
*NOTE: Make sure the silicone O-Ring stays in place
“注意” シリコンO-リングが所定の箇所にあるか確認
*NOTE: Add gear diff grease here (Not Included)
Gear diff grease is for leakage prevention
注意: デフギア用グリスを付ける (別売)
GEAR DIFF FINISHED
x 2 PO-DT1009RD
Spacer
スペーサー
12 x 10 x 0.9t
x 2 PA-SB1510
Bearing
ベアリング
10 x 15 x 4mm
x 4 PA-CM2508BK
Countersunk Screw
皿ビス
M2.5 x 8mm
x 2 PP-GDRS01
Silicone O-Ring
シリコン Oリング
5mm
x 2 PA-SC0312
Countersunk Stainless Steel Hex Screw
皿 ステンレス 六 角ビ ス
M3 x 12 mm
x 2 PA-SB1510
Bearing
ベアリング
10 x 15 x 4mm
BAG A
BAG B
x 2 PA-101215
Shim
シム
12 x 15 x 0.3mm
x 2 PO-DT1009RD
Spacer
スペーサー
10 x 12 x 2mm
x 4 PO-MGBS01
Small Bevel Gear
スモール べベルギア
x 2 PO-MGBS01
Large Bevel Gear
ラージ べベルギア
x 2 PA-HSS101
Shim
シム
5 x 15 x 0.3mm
x 1 PP-GDRS01
Silicone O-Ring
シリコン Oリング
24mm
*Note: Apply small amount of instant glue in between 40T Spool and 40T Flange - One-way/Spool
注意:40T スプールと40T フランジ-ワンウェイ/スプール間に少量の瞬間接着剤をつける
*NOTE: Flat Side Up
注意:平らな面を上
40T Spool
40T スプール
40T Flange - One-way/Spool
40T フランジ-ワンウェイ/スプール
Page 8

*NOTE: Apply small amount of thread lock at the set screws ONLY AT THE THREAD
going into the streeing bridge. Let it dry before installing the ball studs.
少量のスレッドロック剤をイモネジのみにつける
ボールスタッド取付け前に乾燥させる
Chess Head Screw
チェスヘッドネジ
M2 x 5mm
Chess Head Screw
チェスヘッドネジ
M2 x 5mm
Chess Head Screw
チェスヘッドネジ
M2 x 5mm
Chess Head Screw
チェスヘッドネジ
M2 x 5mm
Bearing
ベアリング
5 x 10 x 4mm
Bearing
ベアリング
5 x 10 x 4mm
Bell Crank Bridge
ベ ル クラン クブ リッジ
Spacer
スペーサー
3 x 5.5 x 1.5mm
Set Screw
イモネジ
M3 x 8mm
Shim
シム
3 x 5 x 0.3mm
Countersunk Screw
皿ビス
M3 x 8mm
Shim
シム
3 x 5 x 0.3mm
Bearing
ベアリング
5 x 8 x 2.5mm
Bearing
ベアリング
5 x 8 x 2.5mm
BAG C
PA-SCM205BK
Chess Head Screw
チェスヘッドネジ
x 4 M2 x 5mm
PA-SB1005
Bearing
ベアリング
x 2 5 x 10 x 4mm
PA-SB0805
Bearing
ベアリング
x 4 5 x 8 x 2.5mm
AW-S150RD
Spacer
スペーサー
x 2 3 x 5.5 x 1.5mm
PA-SS0308BK
Set Screw
イモネジ
x 3 M3 x 8mm
PA-CM0308BK
Countersunk Screw
皿ビス
x 2 M3 x 8mm
PA-100305
Shim 3 x 5 x 0.3mm
x 6 シム 3 x 5 x 0.3mm
*NOTE: Over-tightening the screws may cause binding.
締めすぎるに注意
CENTER PULLEY & STEERING CRANK ASSEMBLY / センタープーリー & ステアリングクランク 組立て
CENTER PULLEY ASSM.
FINISHED
STEERING CRANK ASSM.
FINISHED
Page 9

Countersunk Screw
皿ビス
M3 x 8mm
Countersunk Screw
皿ビス
M3 x 6mm
Countersunk Screw
皿ビス
M3 x 8mm
Ultra Wide Collar
ウルトラワイドカラ ー
3mm x 1.0t
Ultra Wide Collar
ウルトラワイドカラ ー
3mm x 0.5t
Ultra Wide Collar
ウルトラワイドカラ ー
3mm x 0.5t
SUSPENSION MOUNT HOLDERS, BULKHEADS & MOTOR MOUNT ASSEMBLY
サスペンションマウントホルダー, バルクヘッド & モーターマウント組立て
BAG D
AW-M050RD
x 12 Ultra Wide Collar
ウルトラワイドカラ ー
3mm x 0.5t
AW-M100RD
x 2 Ultra Wide Collar
ウルトラワイドカラ ー
3mm x 1.0t
PA-CM0308BK
x 14 Countersunk Screw
皿ビス
M3 x 8mm
PA-CM0306BK
x 14 Countersunk Screw
皿ビス
M3 x 6mm
PA-CM0308BK
x 2 Countersunk Screw
皿ビス
M3 x 8mm
Page 10

Stainless Steel Button Head Screw
ステンレスボ タンヘッドネジ
M3 x 30mm
Center Shaft Spacer
センターシャフトスペーサー
Center Shaft Spacer
センターシャフトスペーサー
M3 Steel Nylon Lock Nut
M3 スチールナイロンロックナット
BAG E
TC-PMLS02 ( BAG C)
Center Shaft Spacer
x 2 センターシャフトスペーサー
PA-LN00M3
M3 Steel Nylon Lock Nut
x 1 M3 スチールナイロンロックナット
PA-SF0330
Stainless Steel Button Head Screw
ステンレスボ タンヘッドネジ
x 1 M3 x 30mm
NOTE : Default Spur Gear Position
注意:初期設定スパーギア位置
NOTE : Default belt tension marker position
注意:初期設定ベルトテンションマーカー位置
NOTE : Default belt tension marker position
注意:初期設定ベルトテンションマーカー位置
Spool Assm. From P.7
スプール組立て P.7
から
Center Pulley Assm. From P.8
センタープーリー組立て P.8から
Gear Diff Assm. From P.7
ギアデフ組立て P.7から
*NOTE: Align the center shaft and “slide” into the slots
at the motor plates very carefully.
“注意” センターシャフトを揃え、注意深くモータープレー
ト側 で スロットに スライドさ せます。
DRIVE TRAIN ASSEMBLY / ドライブトレーン組立て
Page 11

Buttom Head Screw
ボタンヘッドネジ
M3 x 6mm
BAG F
AW-S100RD
Collar
カラー
x 4 3 x 5.5 x 1mm
PA-SS0308BK
Set Screw
イモネジ
x 4 M3 x 8mm
PA-BM0306BK
Buttom Head Screw
ボタンヘッドネジ
x 8 M3 x 6mm
PC-CM0306BK
Countersunk Screw
皿ビス
x 4 M3 x 6mm
Buttom Head Screw
ボタンヘッドネジ
M3 x 6mm
Countersunk Screw
皿ビス
M3 x 6mm
Set Screw
イモネジ
M3 x 8mm
Collar
カラー
3 x 5.5 x 1mm
Shim
シム
5 x 7 x 0.2mm
Countersunk Screw
皿ビス
M3 x 6mm
Small M3 Bevel Washer
スモール M3べベルワッシャー
Countersunk Screw
皿ビス
M3 x 6mm
BAG C
PA-100507
Shim
シム
x 2 5 x 8 x 0.2mm
AW-BW31RD
Small M3 Bevel Washer
x 2 スモール M3べベルワッシャー
PA-CM0306BK
Countersunk Screw
皿ビス
x 2 M3 x 6mm
CAMBER LINK PLATES & STEERING INSTALLATION / キャンバーリンクプレート & ステアリング取付け
*NOTE: Apply small amount of thread lock at the set screw ONLY AT THE THREAD
going into the camber link plate. Let it dry before installing the ball stud.
“注意”少量のスレッドロック剤をイモネジのみにつける
ボールスタッド取付け前に乾燥させる
Sterring Crank Assm. From P.8
ステアリングクランク組立て P.8から
make 4
4個作成
Page 12

BAG H
AW-M100RD
Ultra Wide Collar
ウルトラワイドカラ ー
x 2 3 x 7 x 1mm
AW-M200RD
Ultra Wide Collar
ウルトラワイドカラ ー
x 2 3 x 7 x 2mm
AW-S050RD
Collar
カラー
x 2 3 x 5.5 x 0.5mm
AW-S150RD
Collar
カラー
x 4 3 x 5.5 x 1.5mm
AW-S250RD
Collar
カラー
x 2 3 x 5.5 x 2.5mm
Collar
カラー
3 x 7 x 1mm Button Head Screw
ボタンヘッドネジ
M3 x 15mm
Set Screw
イモネジ
M3 x 8mm
Set Screw
イモネジ
M3 x 8mm
Button Head Screw
ボタンヘッドネジ
M3 x 15mm
Collar
カラー
3 x 5.5 x 2.5mm
Collar
カラー
3 x 5.5 x 0.5mm
PA-SS0308BK
Set Screw
イモネジ
x 8 M3 x 8mm
TC-PSUS01
Collar
カラー
x 2 3 x 7 x 0.4mm
PA-BM0315BK
Button Head Screw
ボタンヘッドネジ
x 6 M3 x 15mm
PA-BM0318BK
Button Head Screw
ボタンヘッドネジ
x 2 M3 x 18mm
Collar
カラー
3 x 7 x 2mm
Set Screw
イモネジ
M3 x 8mm
Set Screw
イモネジ
M3 x 8mm
Button Head Screw
ボタンヘッドネジ
M3 x 15mm
Button Head Screw
ボタンヘッドネジ
M3 x 18mm
Collar 3 x 5.5 x 1.5mm
カラー 3 x 5.5 x 1.5mm
Collar 3 x 5.5 x 1.5mm
カラー 3 x 5.5 x 1.5mm
Collar
カラー
3 x 7 x 0.4mm
Collar
カラー
3 x 7 x 0.4mm
FRONT & REAR SUSPENSION ARMS / フロント & リア サスペンションアーム
Right Front Arm
右フロントアー ム
3mm
Left Rear Arm
左リアアーム
*NOTE: Both front & rear arms are left/right symmetrical.
“注意: フロント、リアアーム共に左右対称
2.5mm
3mm
2.2mm
Page 13

BAG G
PO-SDT026RD
44.5mm Universal Bone
x 2 44.5mm ユニバーサルボーン
PO-SDT018
Universal Axle
x 4 ユニバーサル アクスル
PA-SS0303BK
Set Screw
イモネジ
x 4 M3 x 3mm
PA-SS0310BK
Set Screw
イモネジ
x 2 M3 x 10mm
AW-S200RD
Collar
カラー
x 2 3 x 5.5 x 2mm
PA-SB1005
Bearing
ベアリング
x 8 5 x 10 x 4mm
PO-DT1004RD
M2 Wheel Hub Screw
x 4 M2 ホイルハブネジ
PA-SS0308BK
Set Screw
イモネジ
x 2 M3 x 08mm
PA-CM0310BK
Countersunk Screw
皿ビス
X 2 M3 x 10mm
PA-HBS0508
5.3mm Steel Ball Head Screw
x 2 5.3 mmスチールボールヘッドネジ
SUSPENSION ASSEMBLY / サスペンション組立て
PO-SDT009RD
46mm Universal Bone
x 2 46mm ユニバーサルボーン
44.5mm Universal Bone
44.5mm ユニバーサルボーン
Universal Axle
ユニバーサル アクスル
Set Screw
イモネジ
M3 x 3mm
make 2
2個作成
Set Screw
イモネジ
M3 x 10mm
Collar
カラー
3 x 5.5 x 2mm
Bearing
ベアリング
5 x 10 x 4mm
Bearing
ベアリング
5 x 10 x 4mm
M2 Wheel Hub Screw
M2 ホイルハブネジ
Rear Hub Assm. (Make 2)
右ハブ組立て(2個作成)
Bearing
ベアリング
5 x 10 x 4mm
Bearing
ベアリング
5 x 10 x 4mm
M2 Wheel Hub Screw
M2 ホイルハブネジ
Steering Block Assm. (Make 2)
ステアリングブロック組立て(2個作成)
Steering Block Assm.
ステアリングブロック組立て
Universal Axle
ユニバーサル アクスル
46mm Universal Bone
46mm ユニバーサルボーン
Set Screw
イモネジ
M3 x 3mm
make 2
2個作成
Set Screw
イモネジ
M3 x 8mm
Countersunk Screw
皿ビス
M3 x 10mm
5.3mm Steel Ball Head Screw
5.3 mmスチールボールヘッドネジ
Left Castor Assm.
左キャスター組立て
Left Castor Block
左 キ ャス タ ーブ ロ ック
Set Screw
イモネジ
M3 x 8mm
Countersunk Screw
皿ビス
M3 x 10mm
5.3mm Steel Ball Head Screw
5.3 mmスチールボールヘッドネジ
Right Castor Assm.
右キャスター組立て
Right Castor Block
右 キ ャス タ ーブ ロ ック
Page 14

Set Screw
イモネジ
M3 x 6mm
Hinge Pin
ヒンジピン
BAG H
TC-PSU001
Hinge Pin
x 4 ヒンジピン
PA-SS0306BK
Set Screw
イモネジ
x 4 M3 x 6mm
SUSPENSION ASSEMBLY (cont’d) / サスペンション組立て(続き)
Left Hub Assm. from P.13
左キブ組立て P.13から
Right Hub Assm. from P.13
右ハブ組立て P.13から
Set Screw
イモネジ
M3 x 6mm
Hinge Pin
ヒンジピン
Right Castor Assm. from P.13
右キャスター組立て P.13から
Left Castor Assm. from P.13
左キャスター組立て P.13から
Page 15

BAG i
x 10 TC-PMHS01
Ball Cup
ボ ー ル カップ
x 10 14.5mm
x 4 TC-PMHS02
Ball Cup
ボ ー ル カップ
x 4 18.5mm
MC-MLK001
Tie Rod (Steel)
タ イ ロ ッ ド( ス チ ー ル )
x 1 3 x 15mm
TC-PSU005
Tie Rod (Steel)
タ イ ロ ッ ド( ス チ ー ル )
x 6 3 x 30mm
Ball Cup
ボ ー ル カップ
18.5mm
Steering Link (make 2)
ステアリングリンク(2個作成)
20.7mm
Tie Rod (Steel)
タ イ ロ ッ ド( ス チ ー ル )
3 x 30mm
Front Camber Link (make 2)
キャンバーリンク(2個作成)
18.2mm
Tie Rod (Steel)
タ イ ロ ッ ド( ス チ ー ル )
3 x 30mm
Ball Cup
ボ ー ル カップ
14.5mm
Tie Rod (Steel)
タ イ ロ ッ ド( ス チ ー ル )
3 x 30mm
Rear Camber Link (make 2)
リアキャンバーリンク(2個作成)
18.5mm
3.4mm
Ball Cup
ボ ー ル カップ
14.5mm
Servo Link
サ ー ボリンク
Tie Rod (Steel)
タ イ ロ ッ ド( ス チ ー ル )
3 x 15mm
Ball Cup
ボ ー ル カップ
14.5mm
Steering Link
ステアリングリンク
Rear Camber Link
リアキャンバ ーリンク
Front camber Link
フロントキャンバーリンク
LINKAGES / リンケージ
Page 16

BAG F
PA-BM0306BK
Buttom Head Screw
ボタンヘッドネジ
x 16 M3 x 6mm
BAG i
PA-SS0303BK
Set Screw
イモネジ
x 2 M3 x 3mm
AW-ST02RD
Stopper
x 2 ストッパ ー
FINISHED
Stopper
ストッパ ー
Set Screw
イモネジ
M3 x 3mm
Stabilizer Bar
スタビライザーバー
1.2mm ( COPPER ) for rear
1.2 mm (銅色)リア用
1.4mm ( SILVER) for front
1.4 mm (シルバー)フロント用
Buttom Head Screw
ボタンヘッドネジ
M3 x 6mm
Buttom Head Screw
ボタンヘッドネジ
M3 x 6mm
UPPER DECK & STABILIZER BAR ASSEMBLY / アッパーデッキ & スタビライザーバー 組立て
Page 17

Stabilizer Mount S
スタビライザーマウント S
Stabilizer Mount S
スタビライザーマウント S
Stabilizer Mount S
スタビライザーマウント S
Stabilizer Mount S
スタビライザーマウント S
TC-MAAS01
Stabilizer Mount S
x 4 スタビライザーマウント S
PA-SS0303BK
Set Screw
イモネジ
x 4 M3 x 3mm
Button Head Screw
ボタンヘッドネジ
M3 x 10mm
Button Head Screw
ボタンヘッドネジ
M3 x 10mm
BAG i
PA-SS0303BK
Set Screw
イモネジ
x 4 M3 x 3mm
PA-HBS0508
Ball Stud (Steel)
ボールスタッド(スチール)
x 4 5.3 x 8mm
TC-PMHS01
Ball Cup
ボ ー ル カップ
x 4 10.5mm
TC-PMHS02
Ball Cup
ボ ー ル カップ
x 4 14.5mm
PA-BM0310BK
Button Head Screw
ボタンヘッドネジ
x 4 M3 x 10mm
FINISHED
Ball Cup
ボ ー ル カップ
14.5mm
Ball Cup
ボ ー ル カップ
10.5mm
Ball Stud (Steel)
ボールスタッド(スチール)
5.3 x 8mm
Set Screw
イモネジ
M3 x 3mm
Set Screw
イモネジ
M3 x 3mm
Set Screw M3 x 3mm
イモネジ M3 x 3mm
1.4mm from P.16
1.4 mm P.16から
1.2mm from P.16
1.2mmfrom P.16
3.5mm Stablizer Linkage
スタビライザー リンケージ
Stablizer Linkage
Stablizer Linkage
STABILIZER BAR INSTALLATION/ スタビライザーバー取付け
Stabilizer Linkage make 2
スタビライザーリンケージ 2個作成
Page 18

Note: You could choose from a variety of shock piston to suit your needs.
注意: さまざまなショックピストンから必要に応じて選ぶ
1.0mm hole 1.2mm hole
FINISHED
BAG J
PA-BM0310BK
2mm E-Clip
x 8 2mm E- クリップ
TC-PMRS01
Shock Piston
ショックピ ストン
x 4 1.2mm - 2 hole
TC-PSH101RD
Shock Bottom Cap
x 4 ショックボトム
TC-PSH101RD
Shock Top Cap
x 4 ショックトップ キ ャップ
PP-010320
OIL MIXED O-RING FOR DAMPERS 30
x 4 オイルミックスO-リング ダンパー30用
TC-PSH101RD
Spring Adjuster Nut O-Ring
x 4 スプリングアジャスターナット O-リング
Shock Piston
ショックピストン
1.2mm - 3 hole
Shock Bottom Cap
ショックボトム
Shock Top Cap
ショックトップ キ ャップ
2mm E-Clip
2mm E- クリップ
OIL MIXED O-RING FOR DAMPERS 30
オイルミックスO-リング ダンパー30用
Spring Adjuster Nut O-Ring
スプリングアジャスターナット O-リング
*NOTE
Front : Shock Spring (14 x 1.5 x 5.75) Shock Oil / ショックオイル : 60wt.
ショックスプリング (14 x 1.5 x 5.75)
Rear : Shock Spring (14 x 1.5 x 6.50) Shock Oil / ショックオイル : 40wt.
ショックスプリング (14 x 1.5 x 6.50)
Shock Top Cap
ショックトップ キ ャップ
SHOCK ASSEMBLY (MAKE 4) / ショック組立て(4個作成)
Page 19

SHOCK INSTALLATION / ショック取付け
BAG J
PA-BM0306BK
Button Head Screw
ボタンヘッドネジ
x 4 M3 x 6mm
Button Head Screw
ボタンヘッドネジ
M3 x 6mm
Button Head Screw
ボタンヘッドネジ
M3 x 6mm
Front Shock Tower
フロントショックタワー
Rear Shock Tower
リアショックタワ ー
Page 20
Table of contents
Languages:
Other TOP racing Motorized Toy Car manuals

TOP racing
TOP racing Sabre S4 User manual

TOP racing
TOP racing Rebel F1X User manual

TOP racing
TOP racing Rebel 10 User manual

TOP racing
TOP racing PHOTON User manual

TOP racing
TOP racing Rebel 12 User manual

TOP racing
TOP racing Sabre 4WD Mini S-MB01 User manual

TOP racing
TOP racing Sabre S4 User manual

TOP racing
TOP racing Rebel R-F01 User manual