Mattel HotWheels ROAD WARS LIBERTY BASE User manual

93920-0920
INSTRUCTIONS
-~~ 4iC
~.~ SEAT
V~.BAZOOKABASE
STAIRSTOP ~~ ~
\2 MISSilES BAZOOKA' BAZOOKA
SUPPORT
ST"RSBOTTOM ~~4'
~ HELICOPTERBODY LANDINGSKID CAGE
1f~~UTTLESPONGES ~
'if "LASER' @ ~ T ~
LAMPPOST GUN SHRAPNEL 1 &2 CARGUN CAR
CONTENTS: STRING LABELS
RAMP 0SHOULDER ARM
~~ I,'RUBBERS f:.
~"GURE I
WCLIP
DOOR FRAME '0°: a '''0 '
,0 '1'0
~~ .CRANE
VIDEOSCREEN POST
DOORS,
LEFT/RIGHT
STATUE FACE
STATUE BODY
~
ELEVATOR ~~
CRANE
LEFT/RIGHT
ELEVATOR
RAil ~
CRANK @(@
PULLEY WHEEL
LEFT/RIGHT
~
TAil ROTOR PIN T
~MAIN
TAILROTOR ROTORPIN
~~4
HELICOPTER GUN
LEFT/RIGHT
~,.
DAMAGE
DETAIL 2 FIGURES
CUT PARTSFROM FRAMESWITHSAFETY SCISSORS.
SET NOTFOR USE WITHSOME VEHICLES.

INSTALL BATTERIES: IIF\
CRANE \U
BOTTOM IPOST
VIEW'
~'~
.
/' .,.
,
'" ",,~ tJ rJ
S~~,
~I T '-'\-'
Open battery cover door.
Install3 "AA"alkaline'
batteries. Be sure to follow
+ and ~ alignment as
shown. Close battery door.
See battery caution on
back.
ARM
BASE ASSEMBLY
I
(Unless otherwise indicated with a star
'~,*",apply all labels by number prior to
~ssembly) - ,
4.) Snap 'S onto (" 'frame.
S) Snap <..~Jfframe 'i,...,)main base.
C) Snap statue, body into main base
I(over door). '
0» Snap arm into shoulder then snap
1shoulder into main base (over door).
E;I)Snap shoulder into statue body. '
1) Assemble flame, then crane post,
as shown (* assemble flame halves
Ibefore applying label).
G)Assemble crane as shown.
~)Snap assembled crane into ramp
base,
Ithen snap ramp base into main base,
I) Snap crown guns into statue body
( crown.
J~Snap damage detail into statue body.
I
CROWN GUNS
~
REARVIEW
Slide bazooka base into
slot in floor. Make sure
it slides back and forth.
Install seat, bazooka
support and bazooka
as shown.
~
l
i1
,I
I~,I ~
' ". ESCAPE LINE
,ASSEMBLY
/I,' "~

Push missile into bazooka until
it clicks in place. Push down on
pin to fire.
~
@
Install top and bottom stairs
as shown. @
Face should swivel freely and fit
into place to conceal bazooka
when base is pulled back.
@
'I
u
£
\\11
--
Slide elevator onto elevator rail,
snap elevator rC3.ilinto place. Snap on crown as shown.

ESCAPE LINE
.ASSEMBLY
+ cUlU ~ allYIIlIIt::lll i:1::>
shown. Close battery door.
See battery caution on
back. .
ASSEMBLY
RADAR BEACON. CRANE ASSEMBLY:
RUBBER @
PULLEY WHEEL ~HT
APPLY ALL LABELS BY NUMBER.
"PL" SENSOR
SET NOT FOR USE WITH SOME~EHIJ;;~,L.§.§~x,:.. CRANE LEFT

RIG HELICOPTER: ~
Position main rotor blades
on top of helicopter and
fasten with pin. Do the
same with tail rotor.
(f)
iw
Place pilot in seat and
snap on front cage.
Snap on landing
skids as shown.
Install machine guns
on both sides of helicopter.
Set requires a total of 5 AA alkaline batteries (not included).
For best performance and longer life, use only alkaline batteries.
CAUTION:To prevent battery leakage:
1. Be sure to insert batteries correctly and always follow the toy and
battery manufacturer's instructions.
2. Never mix old with new batteries (replace all batteries at the
same time).
, ". Never mix alkaline, standard (carbon-zinc) or rechargeable
- (nickel-cadmium) batteries.
4. Always remove exhausted or dead batteries from the product.
5. Check that the contact surfaces are clean before installing batteries.
6. Remove batteries from product before extended storage.

RIG FOR EXPLOSIONS:
Turn set on.
Place lamppost and
laser gun as shown. Push
into main base until they click
into place.
Insert car gun into car as shown
(lower right) then place car with car
gun as shown (upper right). Push into
main base until it clicks into place.
Pile shrapnel and foam bricks around
bases of lamp post and laser gun for
maximum effect when explosion occurs.
Press helicopter on/off switch (side
opposite shown in "T") to activate
helicopter laser. Aim laser at Radar Beacon
to "Blow up" your targets. Explosions can
sometimes be triggered by covering the
"PL" sensor (right of radar beacon).
"For best results, do not place the toy in direct sunlight or
in bright light. Always face the sensor away from the light:'
TWO YEAR LIMITED WARRANTY
Mattei, Inc. warrants to the original consumer purchaser that this product will be free from defects in material or
workmanship for 2 years (unless otherwise specified in alternate warranties) from the date-of-purchase.1f defective,
return the product along with proof of the date-of-purchase, postage prepaid, to Consumer Adjustment Center,
15930 E. Valley Boulevard, City of Industry, CA 91744 for replacement or refund at our option. This warranty does
not cover damage resuJting from accident. misuse or abuse. VAUD
ONLY IN U.S.A. This warranty gives you specific legal rights and you
may also have other rights which vary from state to state.
Send only the product to the address above. Send all
correspondence to Consumer Affairs, Mattei, Inc.. 333 Continental
Blvd.. EI Segundo, CA 90245-5012, U.S.A. Or you may phone us
toll-free at 1-800-524- TOYS, Monday through Thursday: 8:00
a.m.-5:oo p.m. PST (11:00 a.m.-8:oo p.m. EST); Friday: 8:00
a.m.-12:30 p.m. PST (11:00 a.m.-3:30 p.m. EST).
mmr.1I( hi
tYOUtM1B.lII'SIW19JCAI! xw
iICII"'I :r ai>I>m"'qs.x
.JI. ..mz.1 i",""",-8IIIaa.-5BI1UIl1'Sl:
~11:OOa.-aoo;or.5Unca,.8III I2:.1)p.m.
i'ST.11:OO S3)1UIlt5i~IJ.SA.",
-CRcIOrTIIJ-tsmg.
~=-~u:~:m~Bhd..
1(800)524.TOYS
A inr CONFORMSTOTHESAFETY
Lm.~ REQUIREMENTSOFAS1U F963-92.'
~ 1995 Mattellnc.. EI Segundo, CA 90245 U.S.A.
PRINTED IN ITALY. All Rights Reserved. Wearededicated10qualityproducts.