Tornado PS Series 98220 Manual

TORNADO INDUSTRIES
7401 W. LAWRENCE AVENUE
CHICAGO, IL 60706
[phone] FAX [phone]
www.tornadovac.com
Tornadoâ
ââ
â
Operation & Maintenance Manual
For Commercial Use Only
The PS Series of Carpet Spotters (Series F)
Catalog No.
64220 & 98220 (115v, 60Hz)
98221 (230v, 50HZ)
L2700FG 9/01 ã2001 Tornado Industries All rights reserved.

2
NOTES

3
This instruction book covers:
CATALOG NO. 98220 98221 64230
SERIES FF F
PUMP 55 PSI 55 PSI 55 PSI
VACUUM 94 CFM
84”H2O
82 CFM
68”H2O
94 CFM
84”H2O
CAPACITY 2 Gal 2 Gal (7.6l) 2 Gal
VOLTS 115V 230V 115V
AMPS 84 8
CERTIFICATION **
*
*This product conforms to ANSI/UL Standard 561
and is certified to CAN/CSA Standard C22.2 No. 10.
ALL SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.

4
TABLE OF CONTENTS:
Safety Instructions 5
Electrical/Grounding Methods 7
Unpacking Precautions 9
General Precautions 11
Preparation Instructions 12
Operating Instructions & Cleaning Tips 13
Maintenance Instructions 15
Main Assembly 16
Optional Handle Assembly 18
Vacuum/Pressure Hose Assembly 19
Wiring Diagram (115V) & Accessories 20
Wiring Diagram (230V) 21
Tornado®Standard Warranty Program*
10 Years:
All plastic tanks and
rotationally-molded bodies
2 Years:
Parts on all Tornado and Tornado/Karcher
cleaning equipment 1) 2)
1 Year:
Labor on all Tornado and Tornado/Karcher
cleaning equipment 1) 2)
Warranties do not cover
components subject to normal
wear or abuse and misuse, and
have other limitations not
specified here. For full details ,
contact your Authorized Tornado
Distributor, Service Center, or the
Tornado Technical Service
Department.
1 Year:
Warranty on batteries, one full year,
Not pro-rated.
* Effective January 1st, 2001. Terms subject to change without notice.
1) Windshear™ Blower-Dryer, Insulation Blowers, CW 50, CW 100, and Duo-Upright
Carpetkeepers™ are warranted for 1 (one) year for parts and labor.
2) Warranties on the ICC1, KMR 1200, KMR 1250, and KMR 1700 are 24 months parts/6 months
labor OR 1000 hours of operation, whichever comes first. Warranties on the BR and BD 1000
are 24 months parts/12 months labor OR 1000 hours of operation, whichever comes first.

5
IMPORTANT SAFETY INSTRUCTIONS
WHEN USING AN ELECTRICAL APPLIANCE, BASIC PRE-
CAUTIONS SHOULD ALWAYS BE FOLLOWED INCLUDING THE
FOLLOWING: READ ALL INSTRUCTIONS BEFORE USING THIS
MACHINE.
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY:
1. Do not leave machine unattended when plugged in. Unplug from outlet
when not in use and before servicing.
2. Use indoors only. Do not use outdoors and do not expose to rain.
3. Do not allow to be used as a toy. Close attention is
4. necessary when used by or near children.
5. Use only as described in this manual. Use only manufacturer’s
recommended attachments.
6. Do not use with damaged cord or plug. If machine is not working as it
should, has been dropped, damaged, left outdoors, or dropped into
water, return it to a service center.
7. Do not pull or carry by cord, use cord as a handle, close a door on
cord, or pull cord around sharp edges or corners. Do not run machine
over cord. Keep cord away from heated surfaces.
8. Do not unplug by pulling on cord. To unplug, grasp the plug not the
cord.
9. Do not handle plug or machine with wet hands. Do not put any object
into openings. Do not use with any opening blocked; keep free of dust,
lint, hair, and anything that may reduce air flow.
10. Keep hair, loose clothing, fingers, and all parts of body away from
openings and moving parts.
11. Turn off all controls before unplugging.
12. Use extra care when cleaning on stairs.
13. Do not use to pick up flammable or combustible liquids, such as
gasoline, or use in areas where they may be present.
14. Connect to a properly grounded outlet only. See Grounding
Instructions.
SAVE THESE INSTRUCTIONS

6
IMPORTANTES MESURES DE SÉCURITÉ
L’UTILISATION D’UN APPAREIL ÉLECTRIQUE DEMANDE CERTAINES
PRÉCAUTIONS: LIRE TOUTES LES INSTRUCTIONS AVANT DE FAIRE
FONCTIONNER CET APPAREIL.
AVERTISSEMENT. POUR RÉDUIRE LES RISQUES D’INCENDIE, DE CHOC
ÉLECTRIQUE OU DE BLESSURE:
1. Ne pas laisser l’appareil sans surveillance lorsqui’il est branché.
Débrancher lorsque l’appareil n’est pas utilisé et avant l’entretien.
2. Ne pas utiliser à l’extérieur et ne pas aspirer de matières humides.
3. Ne pas permettre aux enfantes de jouer avec l’appareil. Une attention
particulière est nécessaire lorsque l’appareil est utilisé par des enfantes
ou à proximité de ces derniers.
4. N’utiliser que conformément à cette notice avec les accessoires
recommandés par le fabricant.
5. Ne pas utiliser si le cordon ou la fiche est endommagé. Retourner l’appareil
à un atelier de réparation s’il ne fonctionne pas bien, s’il est tombé ou s’il a
été endommagé, oublié à l’extérieur ou immergé.
6. Ne pas tirer soulever ni traîner l’appareil par le cordon. Ne pas utiliser le
cordon comme une poignée, le coincer dans l’embrasure d’une porte ou
l’appuyer contre des arétes vives ou des coins. Ne pas faire rouler
l’appareil sur le cordon. Garder le cordon à l’écart des surfaes chaudes.
7. Ne pas débrancher en tirant sur le cordon. Tirer plutôt la fiche.
2. Ne pas toucher la fiche ni l’appareil lorsque vos mains sont humides.
3. N’insérer aucun objet dans les ouvertures. Ne pas utiliser l’appareil
lorsqu’une ouverture est bloquée. S’assurer que de la poussière, de la
peluche, des cheveux ou d’autres matières ne réduisent pas le débit d’air.
4. Maintenir les cheveux, les vétements amples, les doigts et toutes les parties
du corps à l’écart des ouvertures et des pièces mobiles.
5. Mettre toues les commandes à la position ARRÊT avant de débrancher
l’appareil.
6. User de prudence lors du nettoyage des escaliers.
7. Ne pas aspirer des liquides inflammables ou
combustibles, comme de l’essence, et ne pas faire fonctionner dans des
endroits où peuvent se trouver de tels liquides.
14 Ne brancher qu’à une prise de courant avec mise à la
terre. Voir les instructions visant la mise à la terre.
INSTRUCTIONS VISANT LA MISE À LA TERRE

7
GROUNDING INSTRUCTIONS
This appliance must be grounded. If it should malfunction or breakdown,
grounding provides a path of least resistance for electric current to reduce
the risk electric shock. This machine is equipped with a cord having an
equipment -grounding conductor and grounding plug. The plug must be
inserted into an appropriate outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
WARNING: Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. Check with a qualified
electrician or service person if you are in doubt as to whether the
outlet is properly grounded. Do not modify the plug provided with the
appliance - if it will not fit the outlet, have a proper outlet installed by a
qualified electrician.
This appliance is for use on a nominal 120-volt circuit, and has a
grounding plug that looks like the plug illustrated in sketch A. A temporary
adapter that looks like the adapter illustrated in sketches B and C may be
used to connect this plug to a 2-pole receptacle as shown in sketch B if a
properly grounded outlet is not available. The temporary adapter should be
used only until a properly grounded outlet (sketch A) can be installed by a
qualified electrician. The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent ground such as a
properly grounded outlet box cover. Whenever the adapter is used, it must
be held in place by a metal screw.
NOTE: In Canada, the use of a temporary adapter is not permitted by
the Canadian Electrical Code
SKETCH A SKETCH B SKETCH C

8
INSTRUCTIONS VISANT LA MISE À LA TERRE
Cet appareil doit etre mis à la terre. En cas de défaillance ou de panne, la
mise à la terre fournit au courant un chemin de moindre résistance qui
réduit le risque de choc électrique. Cet appareil est pourvu d’un cordon
muni d’un conducteur de terre et d’une fiche avec broche de terre. La
fiche doit étre branchée dans une prise appropriée correctement installée
et mise à la terre conformément aux réglements et ordonnances
municipaux.
AVERTISSEMENT. Un conducteur de terre mal raccordé peut
entraîner un risque de choc électrique. Consulter un électricien ou
un technicien d’entretien qualifié si vous n’étes pas certain que la
prise est correctement mise à la terre. Ne pas modifier la fiche
fournie avec l’appareil - si elle ne peut étre insérée dans la prise, faire
installer une prise adéquate par une électricien qualifié.
CROQUIS A CROQUIS B CROQUIS C
Cet appareil est destiné à un circuit de 120 V et est muni d’une fiche de
terre semblable à celle illustrée par le croquis A. Un adaptateur temporaire
semblable à celui illustré par les croquis B peut étre utilisé pour brancher
cette fiche à une prise bipolaire comme l’illustre le croquis B si une prise
avec mise à la terre n’est pas disponible. L’adaptateur temporaire devrait
étre utilisé seulement jusqu’à ce qu’une prise avec mise à la terre soit
installée par un électricien qualifié. L’oreille rigide ou le crochet ou autre
dispositif semblable, de couleur verte, prolongeant l’adaptateur doit étre
raccordé à un élément correctement mis à la terre comme le couvercle
d’une boîte de sortie mise à la terre. L’adaptateur doit étre fixé par une vis
métallique.
NOTE: Au Canada, l’utilisation d’un adaptateur temporaire n’est pas
autorisee par le Code canadien de l’électricité.

9
WHEN THE MACHINE IS DELIVERED
Check the carton carefully for signs of rough handling. Remove the
machine from the carton and look for concealed damage. If the machine is
damaged, notify the carrier immediately and request an inspection. Be
sure to keep the carton, packing inserts, packing lists and carrier’s receipt
until the inspector has verified your claim.
BEFORE OPERATING THE MACHINE
Read the manual carefully and completely before attempting to operate the
unit. This manual has important information for the use and safe operation
of the machine. Keep this manual on file and handy. This machine will
assure years of satisfactory service if operated and maintained according
to recommendations in the manual. If additional information is needed,
please contact your local distributor or write to:
TORNADO INDUSTRIES
7401 W. LAWRENCE AVE.
CHICAGO, IL 60706
708/867-5100
FAX: [phone]
All information and specifications printed in the manual and parts list are
current at the time of printing. However because of Tornado’s policy of
continual product improvement, we reserve the right to make changes at
any time without notice.
This machine was shipped with window washer antifreeze, during the
winter months, in the solution line system to protect the pump and valves
from freezing during transportation and storage. Before you use the unit,
rinse the solution line system with clean water (refer to Protect From
Freezing).

10
WARRANTY
To protect your investment, promptly fill out the
required information on the warranty card that
comes with the unit and mail it back to
Tornado Industries
Note: Service repair and warranty work
is not normally handled at the factory.
WARNING
The machine was designed for use in spot
cleaning on carpeted floors and for upholstery
extraction applications as per instructions and
recommendations written in this manual. Any
deviation from its proper use or purpose and the
consequential damage that may occur is the sole
responsibility of the end user.

11
GENERAL PRECAUTIONS
•Do not use the machine for dry vacuuming. This machine is not fitted
with a dry filter.
•Use defoamer in the recovery tank at all times to prevent damage to the
vacuum motor.
•Do not use water in excess of 140 degrees F (60 degrees C).
•Use only low foaming carpet and upholstery cleaners and defoamers
intended for machines of this type. Do not use dyes, bleaches,
ammonia or other additives. The use of powdered cleaning solution if
not diluted properly may result in the intake screen clogging or damage
to the pump.
•Do not expose machine to freezing temperatures.
•Do not attempt to repair warranted machines. All repairs must be done
by a qualified and authorized repair center. Non warranted repairs will
be billed back to the owner of the unit.
•Do not use any replacement parts except those specified in the parts
list. Unauthorized parts will void the warranty and could cause the unit
not to function properly.
REQUIRED CLEANING CHEMICALS
Use only low foam cleaning chemicals that are designed for carpet and
upholstery extraction.
•General carpet and upholstery extraction cleaner added to the solution
tank.
•Traffic lane pre-spray usually applied with a hand or pump-up sprayer.
•Spotter used with a hand sprayer.
•Defoamer only goes into the recovery tank.
CAUTION: Use as directed. Do not over-use the cleaning chemicals.
EXTENSION CORD
If an extension cord is used, the wire size must be a least one size larger
than the power cord on the machine. The ProSpot is equipped with a 25’
18-3 power cord.
FAILURE TO COMPLY WITH THE ABOVE WARNING INSTRUCTIONS
WILL VOID THE WARRANTY.

12
PREPARING THE MACHINE:
WARNING!! To prevent possible disease hazard, before
attempting to clean bodily fluid spills, you must kill any
viruses, germs or bacteria present in the bodily fluid.
1. Loosen the two latches that hold the recovery tank to the solution tank.
Lift the recovery tank off.
2. Pour up to 2 gallons (7.6 liters) of hot water into clean solution tank.
Water temperature must not exceed 140°F (60°C). Pour in a non-
foaming cleaning concentrate to the proper dilution noted on the
container. Be sure that the vacuum motor foam filter is in place
(located on top of the solution tank).
3. Place the recovery tank on the solution tank and refasten the tank
latches. Attach hand tool to solution and vacuum hoses. Attach solution
hose to fitting on front of solution tank (98225 & 98226 only). Be sure
hose coupler locks onto extractor’s coupler. Connect vacuum hose to
recovery tank.
4. Plug power cord into a grounded outlet. See GROUNDING
INSTRUCTIONS.
5.See “Illustrated Parts List and Wiring Diagram” for available
accessories.

13
OPERATING THE PROSPOT:
1. Turn the switch, located on the rear panel, to “VACUUM/SPRAY”.
2. Place the hand tool on the surface to be cleaned and squeeze the
solution lever. Move tool over surface to be cleaned. Note: Do not apply
too much solution to upholstery to minimize dry time.
3. Always monitor recovered solution in the recovery tank. Excess water
can be drawn into the vacuum motor resulting in damage to the motor.
Turn machine off and empty recovery tank periodically. This machine is
equipped with a float shut off to help prevent damage to the vacuum
motor.
4. At the end of job turn switch to ‘OFF’ and disconnect power cord from
outlet. Empty recovery tank (turn upside down and empty through hose
intake) and solution tank of any solutions. Thoroughly rinse both tanks
to remove any residue and to keep tanks fresh.
CLEANING TIPS:
•Check the condition of the carpeting. If the carpet is loose, heavily
soiled, stained, spotted or badly worn, point this out to the person in
charge.
•Locate an inconspicuous spot on the area to be cleaned. Test carpet for
colorfastness before proceeding. Pour the concentrated cleaning
solution on the spot, cover with a white towel and place a heavy object
on top to absorb the cleaning solution. Wait 10 minutes for any reaction
to take place. Remove weight. If there is no color transfer, it should be
safe to clean.
•Clean the area first with a Clean-Air Carpetkeeper, upright vacuum. Do
not use the ProSpot as a dry vacuum! Heavily soiled carpet or areas of
concentrated foot traffic should be treated with
•recommended pre-spotting or pre-spray chemicals, using a hand spray
trigger bottle or pump up sprayer. Do not allow any spotter or pre-spray
to dry on the carpet. Use a small hand held carpet brush to agitate the
carpeting. Always agitate toward the center of the spot.
•After spot cleaning the carpet, place a small square of aluminum foil or
6 mil poly square under the furniture legs to prevent moisture from

14
damaging the finish or rusting the metal glides, if placing furniture on
moist carpeting.
•Identify the type of carpet fiber to be cleaned. Most carpet fibers in use
are nylon or acrylic based. Best results in cleaning would be obtained if
hot water is used to clean these types of fibers. On the other hand, hot
water could shrink natural fiber carpeting, like wool and cotton in
particular. Exercise caution when cleaning natural fibers. Use cool water
test for colorfastness and apply the least amount of cleaning solution as
possible.
•Furnishings have many different types of fabric. Be sure that the proper
chemicals are used and that you follow the chemical manufacturer’s
directions.
•When the ProSpot runs out of cleaning solution, noted by streaking or
no solution flow, turn off the machine and drain the recovery tank. Refill
solution tank and continue cleaning.
•To decrease drying time go over the carpet and/or furnishings without
squeezing the spray lever or turn the power switch to “VACUUM ONLY”.
To further decrease the drying time, use the Windshear 3000 Carpet
Blower.
PROTECT FROM FREEZING
If it becomes necessary to store in temperatures that could drop below 40
degrees F, the pumping system, hoses and valves must be protected from
freezing with a methyl hydrate window washer antifreeze solution. Do not
use ethylene glycol or cooling system antifreezes.
•Add one quart of windows washer antifreeze to the solution tank, turn
on the pump and squeeze the spray lever until antifreeze solution fills
the solution lines.
•Always allow the unit to reach room temperature before turning on to
remove the antifreeze from the system.

15
MAINTENANCE:
WARNING!! Always unplug power cord before cleaning,
making adjustments or repairs.
AFTER EACH USE:
•Thoroughly flush out both tanks. HINT: To clean the recovery tank turn
upside down and lightly spray into the vacuum intake. this will
“backflush” the filter screen and float shut-off ball. Drain tank through
the hose intake.
•Wipe down entire unit with cleaning solution.
•Flush pump system with 1 quart clean water with 1 ounce white vinegar.
•Remove and clean foam vacuum filter. Remove lint from vacuum motor
intake screen. Store with tanks exposed in clean dry place.
•Inspect power cord for damage. Replace if necessary. Wipe and coil the
cord from machine to the plug then place coiled cord through molded
handle for storage or transport.
•Remove lint from hand tool opening. HINT: Back-flush through vacuum
hose end.
PERIODIC MAINTENANCE
•It is highly recommended that once a month you flush the ProSpot out
with a 8 to 1 ratio of water to white vinegar or anti-browning solution
through the extractor. This will help to prevent the build up of alkaline
residue.
•If the spray jet becomes clogged, remove and wash it thoroughly and
blow dry. Do not use wire or pins to clean the nozzle as this will cause
the spray pattern to become distorted, thereby giving you a streaking
pattern on the carpeting.
•Once a month, inspect all electrical cables, hoses, filters and
connections in the ProSpot. If you see something that should be
repaired or replaced this should be reported and repaired. Little things
are easy to forget, but as these little things add up you end up with a
cluster of problems that will cost you more in the long run.
•Inspect the vacuum motor carbon brushes after every 700 hours of use
replace, if necessary.
•Be sure to use genuine Tornado parts and that service is provided by an
authorized Tornado Service Center. 1-800-VACUUMS Use of non-OEM
parts will void the warranty.

16
ES SERIES CARPET SPOTTERS
64230, 98220 & 98221
MAIN ASSEMBLY (REF. DWG. 98221)
ITEM NO. DESCRIPTION PART NO. QTY.
1SCREW-SLOTTED ROUND HEAD MACHINE #8-32 x ¾ 00600 2
2WASHER-LOCK (H/S) #10 01713 1
3NUT-HEX LOCK (KEPS) #8-32 02956 2
4SCREW-PHILLIPS PAN HD. MACH. # 8-32 X 3/8" 02995 4
5WASHER – SEALING ¼ 07741 2
6NUT-HEX.LOCK(KEPS) #10-24 10892 6
7WASHER-PLAIN 1/2" 12957 1
12 MOTOR-VACUUM,115V/50-60HZ (98220 & 64230 ONLY) 14800 1
(12) MOTOR-VACUUM,230V/50-60HZ (98221 ONLY) 17425 1
8FITTING-BRASS NIPPLE 1/4"FPT X 1/4"Q.C. 14881 1
9CLAMP-HOSE(CRIMP TYPE) .433"-.512"(2-EAR) 15065 4
10 FITTING-BRASS ELBOW(45D) 1/4"FPT X 1/4"MPT 15075 2
11 FITTING-BRASS ELBOW 1/4"MPT X 3/8"HB 15223 1
13 SCREW - PHILLIPS TRUSS HD. MACH. #10-24 X 1/2" (SS) 17848 11
14 WASHER-PLAIN #10 (SS) 17850 8
15 WASHER-PLAIN 5/16" (SS) 19191 4
16 SCREW-PHILLIPS FLAT HD. MACH. # 8-32 X 1/2" (BLK.ZINC) 19255 2
17 TANK-SOLUTION (98220 & 98221 ONLY) 19490 1
(17) TANK-SOLUTION (64230 ONLY) 30896 1
18 TANK-RECOVERY (98220 & 98221 ONLY) 19491 1
(18) TANK-RECOVERY (64230 ONLY) 30897 1
49 PUMP- 55 PSI/115VAC - (64230 & 98220 ONLY) 31479 1
(49) PUMP- 55 PSI/230VAC - (98221 ONLY) 31480 1
19 LATCH-DRAW W/ KEEPER 19504 2
20 WHEEL- 6" DIA. X 1-1/4" (BLACK W/ BLK HUB) 19505 2
21 SPACER-5/16" DIA. 19506 2
22 NUT-HEX.LOCK (NYL.INS.) 5/16-18 19513 2
23 ASSEMBLY-VACUUM STACK/FLOAT CAGE 19516 1
24 SCREEN-VAC.MOTOR INTAKE 19517 1
25 FILTER-VAC.MOTOR INTAKE (FOAM) 19520 1
26 PIPE-NIPPLE, PVC 1/4"MPT X 4" LG. 19522 1
27 FITTING-BRASS ADAPTOR 1/4"FPT X 1/4" HB 19523 2
28 FITTING-NYLON ELBOW 1/8"MPT X 1/4"HB 19524 2
29 FILTER-SOL. SCREEN 19525 1
30 HOSE-SOLUTION (SCREEN) 19528 1
31 WASHER-LOCK (I/T) # 8 19530 4
32 SCREW-PHILLIPS PAN HD. MACH. 5/16-18 X 2-1/2" (SS) 19532 2
33 LABEL-"WARNING!TO REDUCE THE RISK OF ELECTRIC..." 19533 1
50 BRACKET-PUMP MTG(RUBBER) 31490 2
34 SCREW-PAN HEAD #10-16 X 1/2" LG. 19565 4
35 GASKET-SOLUTION TANK 19610 1
36 LABEL-"VACUUM ONLY-OFF-VACUUM/SPRAY"SWITCH(PS) 19611 1
37 WASHER-PLAIN 1/2" (SS) 19616 3
38 SHROUD, VAC MOTOR 19937 1
39 WASHER - LOCK E/T #10 30019 6
40 GASKET-VAC. MOTOR BOTTOM 30456 1
41 GASKET, MOTOR TOP 30457 1
42 SWITCH-ROCKER, DPDT (3 POS.) 15A 30472 1
43 BRACKET-VAC. MOTOR MT'G 30475 2
48 BRACKET-PUMP MT'G 31471 1
44 SCREW-PHILLIPS PAN HEAD MACHINE # I0-24 x 3/8 30678 10
45 DECAL-"TORNADO" 30814 1
47 LINE FILTER 31067 1
51 HOSE-SOLUTION (PUMP) 19527 2
46 ASS'Y POWER CORD 115V (64230 & 98220 ONLY) 19499 1
(46) ASS'Y POWER CORD 230V (98221 ONLY) 31059 1
* = NOT SHOWN
( ) = ITEMS TO BE USED WHERE APPLICABLE

17
ES SERIES CARPET SPOTTERS
64230, 98220 & 98221
MAIN ASSEMBLY – EXPLODED VIEW
(REF. DRAWING 98221)

18
ES SERIES PORTABLE CARPET SPOTTERS
64230, 98220, & 98221
HANDLE ASS’Y (REF. DWG. 31215)
ITEM NO. DESCRIPTION PART NO. QTY.
1 Washer-Lock E/T #10 01713 4
2 Screw-Phillips Pan Head Machine #10-24 X 1.000 19617 4
3 Bracket-Pump Mounting (For Reference) 31471 1
4 Handle-Transport 31214 1

19
ES SERIES PORTABLE CARPET SPOTTER
S
64230, 98220, & 98221
ASS'Y VAC./PRESSURE HOSE (REF. DWG. 30744)
ITEM NO. DESCRIPTION PART NO. QTY.
1 Suction Hose, 8' 30735/19529 1
2 Solution Hose Ass'y 30801/19639/19535 1
3 Tool-Utility 30857 1
*4 Plastic Ties-Black 18706 4
* = NOT SHOWN

20
ES SERIES PORTABLE CARPET SPOTTERS
64230, 98220
CIRCUIT ASSEMBLY (REF. DWG. 98220A)
ITEM NO. DESCRIPTION PART NO. QTY.
1 WASHER-LOCK (H/S) #10 01713 1
2 SCREW-TCT (F) PAN HEAD #10-32 X 3/8" 03261 1
3 TERMINAL-CLOSED END CRIMP(INS) 06824 1
*4 STRAIN RELIEF(LIQ.TITE) .35 DIA. CORD 18793 1
5 LEAD-14 GA. X 3" BLACK 19466 2
6 ASSEMBLY-POWER CORD,115V (SPOTTER)
(INCLUDES ITEM 4)
19499 1
7 ASSEMBLY-POWER CORD,230V (SPOTTER) 19500 1
8 TERMINAL-Q.D.FEMALE 1/4" X 22/18GA. (FUL.INS) 19503 1
9 LEAD-18 GA. X 12"GREEN 19536 1
10 LEAD-16 GA. X 12"BLACK 19537 1
11 LEAD-16 GA. X 12"WHITE 19538 1
OPTIONS AND ACCESSORIES
ITEM NO. DESCRIPTION PART NO. QTY.
* TOOL-UTILITY DETAILER (DELUXE) 3-1/2"
SPRAY/VAC.
98341 1
* TOOL-CREVICE DETAILER SPRAY/VAC. 98342 1
* TOOL-UPHOSTERY/CURTAIN (PERFORATED)
4"SPRAY/VAC.
98343 1
* TOOL-UTILITY/STAIR 6" SPRAY/VAC. 98344 1
* = NOT SHOWN