Tornado Genesis User manual

1N00-511 Genesis 80cm Boat Installation Manual - Export v1.0 08/03
©Tornado International Ltd. 2003 -1- Confidential
Genesis
80cm Boat
1N00-511 Installation Manual

1N00-511 Genesis 80cm Boat Installation Manual - Export v1.0 08/03
©Tornado International Ltd. 2003 -2- Confidential
Company Information.
Telephone Fax
Technical Help [phone] (0)121-772-6056 Ask for
Technical
Help
Parts & Accessories [phone] (0)121-772-6056 Ask for the
Parts Dept
Unit Sales [phone] (0)121-772-6056 Katie
Roberts
Comments: [phone] Stuart Bland
Addresses:
Head Office, Sales Office & Production
Tornado International Ltd
Unit 28 Green Lane Industrial Estate
Second Avenue
Birmingham
B9 5QP
England
Tel: [phone]
Fax: [phone]
A Member of the Tornado International Leisure Group

1N00-511 Genesis 80cm Boat Installation Manual - Export v1.0 08/03
©Tornado International Ltd. 2003 -3- Confidential
Conventions used in this Manual
For clarity the following conventions are used in this manual:
Paragraph Heading
Meaning
Tip!
Information which will assist in the operation
of the product
Note!
Information which is important for the correct
operation of the product.
Caution!
Information which is
VITAL
to avoid injury to
persons or damage to the product.
Warning!
Information which is
VITAL
to avoid serious
injury to personnel or the public.
Please take note of the information in shaded areas. If you have any
questions with regard to the correct installation or operation of the product
please contact Tornado International Ltd.
Important – Please Read This!
This manual is provided in good faith and is believed to be accurate. Because
Tornado International have no control over the manner in which the product is
used, users should satisfy themselves that any information or instruction
contained in this manual is appropriate for the conditions under which the
product is being installed and operated.
In the interest of product development, Tornado International reserves the
right to alter or modify the product as necessary.

1N00-511 Genesis 80cm Boat Installation Manual - Export v1.0 08/03
©Tornado International Ltd. 2003 -4- Confidential
On Delivery
Before Opening Crates
1. Check the number of crates delivered agrees with the number on the
shipping documents.
2. Inspect the crates for damage. If any damage is visible note the crate
number, and the position and extent of the damage. If the crates are not to
be opened immediately, the shipping company should be notified as soon
as possible. If the crates are to be opened at this time, wait until the
product is inspected for damage.
3. The crates should be moved to a position close to the operating area
before opening.
4. The crates should be opened carefully, the contents removed and the
quantities checked against the shipping notes. A product identification
chart can be found at Appendix A. If any damage was noted on the outside
of the crates, the product next to the damage should be inspected
carefully. Any damage should be notified to the shipping company as soon
as the product is unpacked. Any shortage should be notified to Tornado
International Ltd. in writing (letter, fax or e-mail) as soon as possible and in
any event not later than 5 days after receipt.

1N00-511 Genesis 80cm Boat Installation Manual - Export v1.0 08/03
©Tornado International Ltd. 2003 -5- Confidential
Before Installation
All equipment (except UK) designed to operate off mains voltage supply (100v
to 240v) is supplied without a connecting plug. Ensure that the required
number of plugs are available before starting the installation.
Caution!
Check that the supply voltage matches the voltage setting on the front of the
PSU and Charger cases. (Dia. 5 & 6)
Tools & Items Required: (These are not supplied with the unit)
Small flat screwdriver
Medium flat screwdriver
Medium cross point screwdriver
Power drill
8mm drill bit
51mm hole cutter
10mm socket and ratchet
¼ whitworth socket (or adjustable spanner)
Soldering Iron
Staple Gun or 3mm cable clips
7mm cable clips
10off each coin/token used
Setting Out the Equipment:
1. Before starting the installation place the consoles on the floor in the
position they are to be mounted. The consoles may be mounted either
indoors or outside. Console number “1” should be on the left with the
consoles running in numerical order to the right.
2. Place the Power Supply Unit (PSU) in the position it will be used. The rear
of the PSU has a large aluminium heat sink. It is important that the PSU is
positioned so that there is an uninterrupted flow of cool air over the heat
sink.
Caution!
The PSU must be mounted indoors and in such a position that the public
do not have access to it. It must be protected from water.
3. Place the chargers in the position they will be used. The top and bottom of
the charger case has vents to provide cooling. It is important that the
chargers are positioned so that there is an uninterrupted flow of cool air
over the vents. Caution!
The chargers must be mounted indoors and in such a position that the
public do not have access to them. They must be protected from water.
4. Check that the PSU and charger mains cables will reach the electric
supply sockets.
5. Lay out the 24V PSU cable and check that it is long enough to reach from
the master console to the PSU.

1N00-511 Genesis 80cm Boat Installation Manual - Export v1.0 08/03
©Tornado International Ltd. 2003 -6- Confidential
Note!
The PSU cable must not be lengthened without consulting Tornado
International Ltd.
Tip!
The master console can be identified by an additional door to the right of
the coin acceptor door. It is usually number 4 or 6. It is the console with
the transmitter inside.
6. If you have more than one console open the console door (the key is in the
spares pack) and locate the console cable coiled up inside. Check that the
cables from all additional consoles reach the console connection sockets
inside the master console.
When you have satisfied yourself that all of the units are suitably positioned
the installation can begin.

1N00-511 Genesis 80cm Boat Installation Manual - Export v1.0 08/03
©Tornado International Ltd. 2003 -7- Confidential
The Installation
The Consoles:
The consoles are usually mounted on a fence or low wall. The lip (See Dia. 3)
at the top of the console serves to locate the console on the top of the wall or
fence and assists in the mounting process. The lip may be removed if required
by marking a line along the top of the console and cutting along the line with a
hacksaw. There are 4 mounting holes in the back of the console and large
cable holes on the back and underside of the console to route the console
connection cables. (See Dia. 2)
Dia. 1 – Console
Dia. 2 – Console
Rear
Dia. 3 – To Remove Lip
(If required)

1N00-511 Genesis 80cm Boat Installation Manual - Export v1.0 08/03
©Tornado International Ltd. 2003 -8- Confidential
Caution!
Whenever possible use the predrilled mounting holes in the rear of the
console (See Dia. 2). If this is not possible, alternative holes may be drilled in
the back of the console only after checking that there are no items or
electronics inside the console, in the area to be drilled. Any damage caused
by not following this instruction is the responsibility of the installer.
1. With the coin acceptor door open the console should be placed in the
chosen position on the wall or fence to which it is to be fixed.
2. The position of the mounting holes (and cable holes if required) should be
marked on the wall or fence using a scribe or pencil from inside the
console.
3. The console can then be removed and using an 8mm drill bit, the four
mounting holes can be drilled in the wall or fence. Any required cable
holes can then be drilled in the wall or fence,
using a 51mm hole saw.
4. Locate the console mounting bolts and position
the bolts with one washer under the head through
the wall or fence from the model operating side.
5. Prepare four washers and wing nuts. With a
helper holding the bolts in place, lift the console
into position and locate it onto the mounting bolts.
Fit a washer and wing nut to each bolt and
tighten securely.
6. Repeat for each console.
The Power Supply Unit:
The PSU (See Dia. 5) can either be stood on a shelf or hung on a wall using
the slots in the sides of the case. The rear of the PSU has a large aluminium
heat sink. It is important that the PSU is positioned so that there is an
uninterrupted flow of cool air over the heat sink.
Caution!
Dia. 4 - Console
Mounting Bolt
Dia. 5 – The PSU

1N00-511 Genesis 80cm Boat Installation Manual - Export v1.0 08/03
©Tornado International Ltd. 2003 -9- Confidential
The PSU must be mounted indoors and in such a position that the public do
not have access to it. It must be protected from water.
The Chargers:
The chargers (See Dia. 6) must be mounted on a wall using the slots in the
rear of the case. The top and bottom of the charger case has vents to provide
cooling. It is important that the chargers are positioned so that there is an
uninterrupted flow of cool air over the vents.
Caution!
The chargers must be mounted indoors and in such a position that the public
do not have access to them. They must be protected from water.
The chargers should now be connected to the electric supply. The batteries
are fully charged when the unit is dispatched from the factory, however if the
unit has been in transit for some time it might be prudent to charge the
batteries whilst the rest of the installation is carried out. See the section “The
Battery Chargers” in the operation manual for how to charge the batteries.
Dia. 6 – The Charger

1N00-511 Genesis 80cm Boat Installation Manual - Export v1.0 08/03
©Tornado International Ltd. 2003 -10- Confidential
Routing the Console Cables:
Each console has a grey cable coiled inside the console on the side nearest
the master console. Each of these has to be routed out of the console and into
the master console. The cables should be supported using 8mm cable clips
every 30cm.
1. Open the coin acceptor door and locate the console cable.
2. Uncoil the cable and feed the plug out of the console using one of the
large holes in the back or bottom as required.
3. Route the cable to the master console and fit the plug into the correct
numbered socket on the transmitter motherboard (See Dia. 7) (The socket
numbers are on the transmitter motherboard cover). Do not fix the cables
in position at this time.
4. Repeat the routing for all console cables. It should be noted that the cable
for the master console is fitted at the factory. All of the console cables are
the same length so some surplus will remain for consoles close to the
master console.
5. Leaving a small loop of cable in the master console, fix the cables in
position starting at the master console and working toward the standard
console(s).
6. Coil up any excess cable and place it inside the standard console to one
side, ensuring that the coil of cable does not interfere with the operation of
any of the console controls.
Dia. 7 – The Transmitter Mother Board showing the Master Console Connection Sockets
(Inside the access door of the master console)