Toro DINGO 525 Firmware update

TORO DINGO 525
COMPACT UTILITY LOADER
OPERATOR'S MANUAL LOCATED
IN WEATHER TITE BOX.
Safety
Improper use or maintenance by the operator
or owner can result in injury. To reduce
the potential for injury, comply with these
safety instructions and always pay attention
to the safety alert symbol A, which means:
Caution, Warning, or Danger-personal
safety instruction. Failure to comply with the
instruction may result in personal injury or
death.
Safe Operating Practices
This product is capable of amputating hands and
feet. Always follow all safety instructions to avoid
serious injury
or death.
Engine exhaust contains carbon monoxide,
an odorless, deadly poison that can kill you.
Do not run the engine indoors or in an
enclosed area.
Training
• Read the Operator's Manual and other training
material.
If the operator(s) or mechanic(s) can
not read English, it is the owner's responsibility
to explain this material to them.
Slope Operation
Slopes are a major factor related to loss-of-control
and tip-over accidents, which can result in severe
injury
or death. All slopes require extra caution.
•
Do not operate the traction unit on hillsides
or slopes exceeding the angles recommended
in the Stability Data section in Specifications,
page 17,
and those in the attachment Operator's
Manual See also the Slope Chart, page 8.
• Operate up and down slopes with the
heavy end of the traction unit uphill. Weight
distribution changes.
An empty bucket will
make the rear of the traction unit the heavy
end, and a full bucket will make the front of
the traction unit the heavy end. Most other
attachments will make the front of traction
unit the heavy end.
Controls
Become familiar with all the controls (Figure 4)
before you start the engine and operate the traction
unit.
10 9
Figure 4
1. Auxiliary hydraulics lever 6. Throttle lever
2.
Key switch 7. Loader arm/attachment tilt
lever
3. Hour meter 8. Parking brake lever
4. Fuel
gauge 9. Reference bar
5. Indicator lights and glow 10. Traction control
plug switch
Reference Bar
When driving the traction unit, use the reference
bar as a handle and a leverage point for controlling
the traction control and the auxiliary hydraulics
lever.
To ensure smooth, controlled operation, do
not take both hands off of the reference bar while
operating the traction unit.
Traction Control
To move forward, move the traction control
forward. To move rearward, move the traction
control rearward (Figure 5).
To turn rotate the traction control in the desired
,
direction (Figure 5).
The farther you move the traction control in any
direction,
the faster the traction unit will move in
that direction.
To stop, release the traction control.
Figure 5
I

loader Arm/Attachment Tilt Leyer
To tilt the attachment forward, slowly move the
lever to the right (Figure 6).
To tilt the attachment rearward, slowly move the
lever
to the left (Figure 6).
To lower the loader arms, slowly move the lever
forward (Figure 6).
To raise the loader arms, slowly move the lever
rearward (Figure
6).
You can also push the lever fully forward into a
detent position (Figure
6) to release the loader
arms so that the attachment rests on the ground.
This allows attachments such as the leveler and
the hydraulic blade to follow the contours of the
ground (i.e., float) when grading.
Figure 6
1. Lower the loader arms 4. Tilt the attachment forward
2.
Raise the loader arms 5. Detent (Float) position
3. Tilt
the attachment
rearward
By moving the lever to an intermediate position
(such as, forward
and left), you can move the
loader arms
and tilt the attachment at the same
time.
Key Switch
The key switch, used to start and stop the engine,
has three positions: off,
run, and start.
To start the engine, rotate the key to the start
position. Release the key
when engine starts and it
will move automatically to the run position.
To stop the engine, rotate the key to the off
position.
Throttle Leyer
Move the control forward to increase the engine
speed
and rearward to decrease speed.
Auxiliary Hydraulics Leyer
To operate a hydraulic attachment in the forward
direction, rotate the auxiliary hydraulics lever
rearward
and pull it down to the reference bar
(Figure 7, number 1).
To operate a hydraulic attachment
in reverse
direction, rotate the hydraulics lever rearward,
then
move it left into the upper slot (Figure 7, number
2).
If you release the lever while in the forward
position,
the lever will automatically return to the
neutral position (Figure 7,
number 3). If it is in
the reverse position, it will remain there until you
pull
it out of the slot.
1~
GOO4179
Figure 7
1. Forward flow hydraulics 3. Neutral
2. Reverse flow hydraulics
Parking Brake lever
To set the parking brake, push the brake lever
forward
and to the left and then pull it rearward
(Figure 8).
Note: The traction unit may roll slightly before
the brakes engage in the drive sprocket.
Figure 8
IF YOU DO NOT UNDERSTAND OR FORGET
THE INSTRUCTIONS GIVEN OR, IF THE
EQUIPMENT FAILS, DO NOT OPERATE OR
REPAIR IT. CALL MILPAS RENTAL
IMMEDIATELY.