Toro ROPS Reelmaster 5210 User manual

1

2

3
TABLE OF CONTENTS
INTRODUCTION –TO THE PURCHASER 4
PACKING LIST/PARTS PHOTOS 5
DECALS 6
MOUNTING INSTRUCTIONS 7

4
TO THE PURCHASER
All products are designed to give safe, dependable service if they are operated and
maintained according to instructions. Read and understand this manual before
operation.
This manual has been prepared to assist the owner and operators in the safe operation
and suitable maintenance of the canopy. The information is applicable to products at the
time of manufacture and does not include modifications made afterwards.
Read and understand this manual before attempting to put equipment into service.
Familiarize yourself with the operating instructions and all the safety
recommendations contained in this manual and those labeled on the equipment and on
the tractor. Follow the safety recommendations and make sure that those
with whom you work follow them.
Illustrations
The illustrations may not necessarily reproduce the full detail and the exact shape of the
parts or depict the actual models, but are intended for reference only.
Direction Reference
All references to right and left, forward or rearward, are from the operator’s seat,
facing the steering wheel.
Safety Precautions
All products are designed to give safe, dependable service if they are operated and
maintained according to instructions. Read and understand this manual before
operation. It is the owner’s responsibility to be certain anyone operating this product
reads this manual, and all other applicable manuals, to become familiar with this canopy
and all safety precautions. Failure to do so could result in serious personal injury or
canopy damage. If you have any questions, consult your dealer.
To assist your TORO distributor/dealer in handling your needs, please record hereafter
the model number and serial number of your canopy and tractor. It is also advisable to
supply them to your insurance company. It will be helpful in the event that the canopy or
tractor is lost or stolen.
TRACTOR CANOPY
MODEL:
_____________________________________________________________________
SERIAL NUMBER:
_____________________________________________________________________
DATE OF PURCHASE:
_____________________________________________________________________
DEALER NAME:
_____________________________________________________________________

5
PACKING LIST
Description Qty
Bolt, Carriage, M12x40x1.75, Gr. 8.8, YD 6
Nut, Flange, Nylon-Locking, M12x1.75, Gr. 8.8, YD 6
Bolt, Hex, 3/8" x 1 1/2", Gr. 8, YD 10
Nut, Hex, 3/8", Gr. 8, YD 10
Front Brackets L&R
Rear Mounting Bracket 1
Mesh Package Only
Nut, Flange, 5/16”, YD 8
Rear Clamshell Brackets for Door L&R
Bolt, Flange, 5/16" x 3/4", Gr. 5, YD 10
PARTS PHOTOS
Ruler for measuring nuts, bolts, and screws.

6
*NOTE –Parts photos are not to scale.

7
DECALS
1. Keep decals clean. Remove dirt with a wet clean cloth when necessary.
2. Replace safety decals if destroyed, missing, painted over or unreadable. If the tractor
safety decals are covered or obscured when the cab is mounted, purchase replacement
decals from the tractor manufacturer. Mount them in a readable location at, or near, their
original location before operating the tractor.
3. New cab decals and tractor decals are available from your Toro distributor/dealer.
CAUTION
The resulting noise levels when
using this product will exceed
OSHA standards for an 8 hour
workday and hearing protection
with a Noise Reduction Rating
(NRR) of 22 or higher is
required.

8
MOUNTING INSTRUCTIONS
Step 1. Take the front left under platform support bracket and position under the
platform. Fasten into place with two 3/8” x 1 ½” hex bolts and nuts into the side
of the operator platform.
_________________________________________________________
Step 2. Repeat for the right under platform bracket support bracket.
_________________________________________________________
Step 3. Lift the modular ROPS off of the shipping pallet with an over head hoist.
_________________________________________________________
Step 4.Slowly lower the ROPS onto the machine, and get the rear bracket over the 2-
post ROPS first.
_________________________________________________________
Step 5.Take the rear bracket and fasten to the modular ROPS in order to secure the
rear position first. Use the provided M12 fasteners.
_________________________________________________________
Step 6. Use the remaining 3/8” fasteners and bolt the front mount to the platform through
the support brackets installed earlier.
_________________________________________________________
Step 7. Torque all fasteners to recommended specifications.
_________________________________________________________

9
Torque Specifications:
M12 torque: 102 ft-lbs
3/8” torque: 48 ft-lbs