Toshiba MMU-AP0151SH User manual

Indoor Unit
Unité intérieure
Raumeinheit
Unità interna
Unidad interior
Unidade interior
Binnenunit
ÅóùôåñéêÞ mïíÜäá
<1-way Air Discharge Cassette Type>
<Type cassette à 1 voies de soufflage>
<1-Wege-Belüftungskassette>
<Tipo a cassetta con scarico d'aria a 1 vie>
<Modelo de casete de distribución de aire de 1 vías>
<Descarga de ar tipo cassete de 1 vias>
<Model voor inbouw in plafond met 1 uitblaasopeningen>
<ÅêñïÞ áÝñá 1-Äéåõèýíóåùí Ôýðïõ ÊáóÝôáò>
MMU-AP0151SH, MMU-AP0181SH
MMU-AP0241SH
INSTALLATION MANUAL
MANUEL DINSTALLATION
INSTALLATIONS-HANDBUCH
MANUALE DI INSTALLAZIONE
MANUAL DE INSTALACIÓN
MANUAL DE INSTALAÇÃO
INSTALLATIEHANDLEIDING
ÅÃ×ÅÉÑÉÄÉÏ ÅÃÊÁÔÁÓÔÁÓÇÓ
SUPER MODULAR MULTI SYSTEM AIR CONDITIONER
SMMS CLIMATISEUR
SMMS KLIMAGERÄT
SMMS CONDIZIONATORE D'ARIA
SMMS APARATO DE AIRE ACONDICIONADO
SMMS AR CONDICIONADO
SMMS AIRCONDITIONER
SMMS ÊËÉÌÁÔÉÓÔÉÊÏ
SMMS
<Ceiling Panel>
<Panneau pour plafond>
<Deckenkassette>
<Pannello al soffitto>
<Panel del techo>
<Painel de tecto>
<Plafondpaneel>
<ÖÜôíùìá ïñïöÞò>
RBC-US165PG
RBC-US265PG
For commercial use (Not accessible to the general public)
Pour usage commercial (Vente interdite au grand public)
Nur für gewerbliche Nutzung (kein öffentlicher Zugang)
Per uso commerciale (Non accessibile a clienti generici)
Para uso comercial (no destinado al público en general)
Para uso comercial (não acessível ao público em geral)
Voor commercieel gebruik (niet geschikt voor huishoudelijk gebruik)
Ãéá åìðïñéêÞ ñÞóç ( ç äéáèÝóéìï óôï åõñý êïéíü)

ADOPTION OF NEW REFRIGERANT
This Air Conditioner is a new type which adopts a new
refrigerant HFC (R410A) instead of the conventional
refrigerant R22 in order to prevent destruction of the
ozone layer.
UTILISATION DU NOUVEAU REFRIGERANT
Ce climatiseur est d’un type inédit qui utilise le nouveau
réfrigérant HFC (R410A) au lieu du réfrigérant
traditionnel R22, afin d’éviter la destruction de la couche
d’ozone.
EINFÜHRUNG EINES NEUEN KÜHLMITTELS
Dies ist ein neuartiges Klimagerät. Anstatt des
herkömmlichen Kühlmittels R22 verwendet es das neue
ozonschicht-schonende HFC Kühlmittel R410A.
ADOZIONE DI UN NUOVO REFRIGERANTE
Questo condizionatore d'aria èdi un tipo nuovo che
adotta un nuovo refrigerate HFC (R410A) al posto del
refrigerante convenzionale R22, per prevenire la
distruzione dello strato di ozono dell'atmosfera terrestre.
ADOPCIÓN DE NUEVO REFRIGERANTE
Este aparato de aire acondicionado es un modelo
reciente que incorpora el nuevo refrigerante HFC
(R410A) en lugar del refrigerante convencional R22
para asíevitar daños en la capa de ozono.
ADOPÇÃO DO NOVO REFRIGERANTE
Este ar condicionado éum modelo novo que adopta um
novo refrigerante HFC (R410A) em vez do refrigerante
convencional R22 para evitar a destruição da cama de
ozono.
ÕÉÏÈÅÔÇÓÇ ÍÅÏÕ ØÕÊÔÉÊÏÕ
Ôï ðáñüí Êëéìáôéóôéêü åßíáé íÝïò ôýðïò ðïõ õéïèåôåß íÝï
øõêôéêü HFC (R410A) óôç èÝóç ôïõ óõìâáôéêïý
øõêôéêïý R22 ðñïêåéìÝíïõ íá âïçèÞóåé óôçí ðñïóôáóßá
ôïõ üæïíôïò.
TOEPASSINGVAN EEN NIEUW KOELMIDDEL
Deze airconditioner is een nieuwe type dat werkt met
een nieuw koelmiddel HFC (R410A) in plaats van met
het conventionele koelmiddel R22, als bijdrage om de
aantasting van de ozonlaag te reduceren.
Thank you very much for purchasing TOSHIBA Air Conditioner.
Please read this owner's manual carefully before using your Air
Conditioner.
•Be sure to obtain the “Owner’s manual”and “Installation manual”from
constructor (or dealer).
Request to constructor or dealer
Please clearly explain the contents of the Owner’s manual and hand over it.
Nous vous remercions pour avoir choisi un climatiseur TOSHIBA.
Veuillez lire attentivement ce Manuel du propriétaire avant d’utiliser votre
climatiseur.
•Assurez-vous que le constructeur (ou le revendeur) vous remette le
“Manuel du propriétaire”et le “Manuel d’installation”.
Demande au constructeur ou au revendeur
Veuillez expliquer clairement le contenu du Manuel du propriétaire et le
remettre au client.
Wir danken Ihnen, dass Sie sich für einTOSHIBA Klimagerät entschieden
haben.
Bitte lesen Sie diese Betriebsanleitung, bevor Sie Ihr Klimagerät benutzen, sorgfältig.
•Lassen Sie sich die “Betriebsanleitung”und das “Installations-Handbuch”
unbedingt vom Installateur oder vom Lieferanten aushändigen.
Eine Bitte an den Installateur oder Lieferanten:
Bitte erklären Sie dem Käufer den Inhalt der Betriebsanleitung und händigen
sie ihm aus.
Grazie di aver acquistato un condizionatore d'aria TOSHIBA.
Prima di usare il condizionatore d'aria, leggere con attenzione questo
manuale del proprietario.
•Si raccomanda di tenere a portata di mano il “Manuale del proprietario”
e il “Manuale di installazione”ricevuti dal produttore (o dal rivenditore).
Richiesta al produttore o al rivenditore
Spiegare chiaramente il contenuto del Manuale del proprietario e
consegnarne una copia all'utente.
Muchas gracias por haber adquirido el aparato de aire acondicionado TOSHIBA.
Lea atentamente este manual del propietario antes de utilizar el aparato de aire
acondicionado.
•Asegúrese de que el fabricante (o distribuidor) le proporcione el “Manual del
propietario”y el “Manual de instalación”.
Solicitud al fabricante o distribuidor
Explique con claridad el contenido del Manual del propietario y entréguelo al
cliente.
Muito obrigada por adquirir o Ar Condicionado TOSHIBA.
Leia atentamente este manual do utilizador antes de utilizar o seu ar
condicionado.
•Não se esqueça de receber o “Manual do utilizador”e o “Manual de
inslatação”do fabricante (ou agente).
Pedido ao fabricante ou agente
Explique por favor o conteúdo do Manual do utilizador e entregue-o.
Hartelijk dank voor uw keuze voor een airconditioner van TOSHIBA.
Lees deze gebruiksaanwijzing zorgvuldig door voordat u de
airconditioner gaat gebruiken.
•Zorg ervoor dat u zowel de ‘gebruiksaanwijzing’als de
‘installatiehandleiding’van de installateur (of leverancier) krijgt.
Verzoek aan de installateur of de leverancier
Leg de inhoud van de gebruiksaanwijzing duidelijk uit en overhandig de
gebruiksaanwijzing nadien aan de klant.
Óáò åõ÷áñéóôïýìå ðïëý ðïõ ðñïôéìÞóáôå ãéá ôçí áãïñÜ óáò Ýíá
Êëéìáôéóôéêü TOSHIBA.
Ðáñáêáëïýìå äéáâÜóôå ðñïóå÷ôéêÜ ôéò ïäçãßåò ÷ñÞóçò ðñéí áðü ôç ÷ñÞóç
ôïõ Êëéìáôéóôéêïý.
 Âåâáéùèåßôå üôé ï êáôáóêåõáóôÞò (Þ ï ðùëçôÞò) óáò ðáñÝäùóå êáé ôéò
Ïäçãßåò ×ñÞóçò êáé ôï Åã÷åéñßäéï ÅãêáôÜóôáóçò.
ÐáñÜêëçóç ãéá ôïí êáôáóêåõáóôÞ Þ ôïí ðùëçôÞ
Ðáñáêáëþ åîçãÞóôå ìå óáöÞíåéá ôá ðåñéå÷üìåíá ôùí Ïäçãéþí ×ñÞóçò êáé
ðáñáäþóôå ôï.
HFC
R410A R22

CONTENTS
SOMMAIRE
INHALT
INDICE
CONTENIDO
ÍNDICE
ÐÅÑÉÅ×ÏÌÅÍÁ
INHOUD
ITALIANO
ESPAÑOL
PORTUGUÊS
ÅËËÇÍÉÊÁ FRANCAIS
DEUTSCH
NEDERLANDS ENGLISH
Accessory parts and Parts to be procured locally ...........................1
1 PRECAUTIONS FOR SAFETY .....................................................2
2 SELECTION OF INSTALLATION PLACE .....................................4
3 INSTALLATION OF INDOOR UNIT ...............................................5
4 DRAIN PIPING WORK ................................................................ 10
5 REFRIGERANT PIPING ..............................................................12
6 ELECTRICWORK .......................................................................14
7 APPLICABLE CONTROLS .........................................................18
8 TEST RUN ...................................................................................20
9 TROUBLESHOOTING ................................................................. 22
10 MAINTENANCE...........................................................................27
Pièces accessoires et pièces non fournies .....................................28
1 MESURES DE SECURITE ..........................................................29
2 SELECTION DU LIEU D’INSTALLATION ...................................31
3 INSTALLATION DE L’UNITE INTERIEURE ................................32
4 INSTALLATION DESTUYAUX D’EVACUATION .........................37
5 TUYAUX DE RÉFRIGÉRANT ......................................................39
6 TRAVAUX D’ÉLECTRICITÉ........................................................41
7 COMMANDES UTILISABLES.....................................................45
8 ESSAI DE FONCTIONNEMENT .................................................47
9 DÉPANNAGE ...............................................................................49
10 ENTRETIEN.................................................................................54
Zubehör und bauseits bereitzustellendeTeile .................................55
1 SICHERHEITSVORKEHRUNGEN ..............................................56
2 AUSWAHL DES AUFSTELLUNGSORTES .................................58
3 INSTALLATION DER RAUMEINHEIT ......................................... 59
4 INSTALLATION DES KONDENSWASSER-ABLAUFS ...............64
5 KÜHLMITTELLEITUNGEN .........................................................66
6 ELEKTROARBEITEN ..................................................................68
7 STEUERUNGSMÖGLICHKEITEN ..............................................72
8 TESTLAUF...................................................................................74
9 FEHLERSUCHE ..........................................................................76
10 WARTUNG...................................................................................81
Accessori e parti da acquistare sul posto ....................................... 82
1 PRECAUZIONI PER LA SICUREZZA .........................................83
2 SCELTA DEL POSTO D’INSTALLAZIONE .................................85
3 INSTALLAZIONE DELL’UNITÀINTERNA .................................. 86
4 LAVORO PERTUBAZIONE DI SCARICO ..................................91
5 TUBAZIONI DEL REFRIGERANTE ............................................93
6 COLLEGAMENTI ELETTRICI ..................................................... 95
7 COMANDI APPLICABILI ............................................................99
8 FUNZIONAMENTO DI PROVA ..................................................101
9 RISOLUZIONE DEI PROBLEMI................................................103
10 MANUTENZIONE ......................................................................108
Componentes accesorios y componentes de suministro local ..109
1 PRECAUCIONES PARA SU SEGURIDAD ...............................110
2 SELECCIÓN DEL LUGAR DE INSTALACIÓN .........................112
3 INSTALACIÓN DE LA UNIDAD INTERIOR ..............................113
4 CANALIZACIÓN DE DRENAJE ................................................118
5 TUBERÍA DE REGRIGERANTE ...............................................120
6 INSTALACIÓN ELÉCTRICA......................................................122
7 CONTROLES APLICABLES..................................................... 126
8 PRUEBA DE FUNCIONAMIENTO ............................................128
9 RESOLUCIÓN DE PROBLEMAS ............................................. 130
10 MANTENIMIENTO .....................................................................135
Acessórios e peças adquiridas localmente ..................................136
1 PRECAUÇÕES DE SEGURANÇA ............................................ 137
2 SELECÇÃO DO LOCAL DE INSTALAÇÃO ............................. 139
3 INSTALAÇÃO DA UNIDADE INTERIOR................................... 140
4 INSTALAÇÃO DATUBAGEM DE DRENAGEM ........................145
5 TUBAGEM DE REFRIGERANTE ..............................................147
6 TRABALHOS DE ELECTRICIDADE.........................................149
7 CONTROLOS APLICÁVEIS......................................................153
8 TESTE DE FUNCIONAMENTO .................................................155
9 RESOLUÇÃO DE PROBLEMAS .............................................. 157
10 MANUTENÇÃO .........................................................................162
Accessoires en niet meegeleverde onderdelen ............................ 163
1 VOORZORGSMAATREGELENVOOR UWVEILIGHEID .........164
2 KEUZEVAN DE LOCATIE VOOR DE INSTALLATIE ................166
3 INSTALLATIE VAN DE BINNENUNIT .......................................167
4 AFVOERLEIDINGEN .................................................................172
5 KOELMIDDELLEIDINGEN ........................................................ 174
6 ELEKTRISCHE BEDRADING ...................................................176
7 BEDIENINGSELEMENTEN ......................................................180
8 WERKINGSTEST ......................................................................182
9 STORINGEN VERHELPEN ....................................................... 184
10 ONDERHOUD ...........................................................................189
Ðáñåëêüìåíá áíôáëëáêôéêÜ êáé ÅîáñôÞìáôá áðü ôçí ôïðéêÞ áãïñÜ .... 190
1ÐÑÏÖÕËÁÎÅÉÓ ÁÓÖÁËÅÉÁÓ .................................................... 191
2ÅÐÉËÏÃÇ ÔÏÕ ×ÙÑÏÕ ÅÃÊÁÔÁÓÔÁÓÇÓ ................................ 193
3ÅÃÊÁÔÁÓÔÁÓÇ ÔÇÓ ÅÓÙÔÅÑÉÊÇÓ ÌÏÍÁÄÁÓ ...................... 194
4ÅÃÊÁÔÁÓÔÁÓÇ ÓÙËÇÍÙÓÅÙÍ ÁÐÏÓÔÑÁÃÃÉÓÇÓ ................ 199
5ÓÙËÇÍÙÓÇ ØÕÊÔÉÊÏÕ ÌÅÓÏÕ .............................................. 201
6ÇËÅÊÔÑÉÊÇ ÅÑÃÁÓÉÁ ............................................................... 203
7ÅÖÁÑÌÏÓÉÌÏÉ ÅËÅÃ×ÏÉ ......................................................... 207
8ÄÏÊÉÌÇ ËÅÉÔÏÕÑÃÉÁÓ ............................................................. 209
9ÁÍÔÉÌÅÔÙÐÉÓÇ ÐÑÏÂËÇÌÁÔÙÍ ........................................... 211
10 ÓÕÍÔÇÑÇÓÇ ............................................................................... 216
217
1 218
2 220
3 221
4 226
5 228
6 230
7 234
8 236
9 238
10 243

1
Shape
This manual
M5 × 16L
——
Accessory parts and Parts to be procured locally
HAccessory parts
HParts to be procured locally
Connecting pipe (Liquid side)
(6.4mm (diam.), Nominal (diam.) 1/4” thick 0.8mm)
MMU-AP0151SH, MMU-AP0181SH
(9.5mm (diam.), Nominal (diam.) 3/8” thick 0.8mm)
MMU-AP0241SH
Connecting pipe (Gas side)
(12.7mm (diam.), Nominal (diam.) 1/2” thick 0.8mm)
MMU-AP0151SH, MMU-AP0181SH
(15.9mm (diam.), Nominal (diam.) 5/8” thick 1.0mm)
MMU-AP0241SH
Power supply cord
Cable 3-core 2.5mm2, in conformity with Design 60245 IEC57
<Separate sold parts>
Part name
Standard wired
remote controller
Ceiling panel
Q’ty
1
1
Shape Usage
Model
RBC-AMT21E
Model
RBC-US165PG
RBC-US265PG
Refrigerant piping
• Piping material used for the conventional
refrigerant cannot be used.
• Use copper pipe with 0.8 mm or more thickness
for Ø6.4, Ø9.5, Ø12.7.
Use copper pipe with 1.0 mm or more thickness
for Ø15.9.
• Flare nut and flare works are also different from
those of the conventional refrigerant. Take out
the flare nut attached to the indoor unit of the air
conditioner, and use it.
Part name
Installation Manual
Heat Insulating pipe
Installation gauge
Pattern fixing screw
Installation pattern
Connector
Drain-up pipe
Banding band
Q’ty
1
2
1
4
1
1
4
10
Usage
(Be sure to hand over customers)
For heat insulating of pipe connecting section
For positioning of ceiling position
For attach the installation pattern
For confirmation of ceiling opening and indoor unit position
For motor speed up when installed to high ceiling
For drain-up of discharge port
Used to fix drain piping

2
1 PRECAUTIONS FOR SAFETY
•Ensure that all Local, National and International regulations are satisfied.
•Read this “PRECAUTIONS FOR SAFETY”carefully before Installation.
•The precautions described below include the important items regarding safety. Observe them without fail.
•After the installation work, perform a trial operation to check for any problem.
Follow the Owner’s Manual to explain how to use and maintain the unit to the customer.
•Turn off the main power supply switch (or breaker) before the unit maintenance.
•Ask the customer to keep the Installation Manual together with the Owner’s Manual.
CAUTION New Refrigerant Air Conditioner Installation
•THIS AIR CONDITIONER ADOPTS THE NEW HFC REFRIGERANT (R410A) WHICH DOES NOT
DESTROY OZONE LAYER.
The characteristics of R410A refrigerant are ; easy to absorb water, oxidizing membrane or oil, and its pressure
is approx. 1.6 times higher than that of refrigerant R22. Accompanied with the new refrigerant, refrigerating oil
has also been changed. Therefore, during installation work, be sure that water, dust, former refrigerant, or
refrigerating oil does not enter the refrigerating cycle.
To prevent charging an incorrect refrigerant and refrigerating oil, the sizes of connecting sections of charging
port of the main unit and installation tools are charged from those for the conventional refrigerant.
Accordingly the exclusive tools are required for the new refrigerant (R410A).
For connecting pipes, use new and clean piping designed for R410A, and please care so that water or dust does
not enter. Moreover, do not use the existing piping because there are problems with pressure-resistance force
and impurity in it.
CAUTION To Disconnect the Appliance from Main Power Supply.
This appliance must be connected to the main power supply by means of a switch with a contact separation of
at least 3 mm.
WARNING
•Ask an authorized dealer or qualified installation professional to install/maintain the air
conditioner.
Inappropriate installation may result in water leakage, electric shock or fire.
•Turn off the main power supply switch or breaker before attempting any electrical work.
Make sure all power switches are off. Failure to do so may cause electric shock.
•Connect the connecting wire correctly.
If the connecting wire is connected in a wrong way, electric parts may be damaged.
•When moving the air conditioner for the installation into another place, be very careful not
to enter any gaseous matter other than the specified refrigerant into the refrigeration cycle.
If air or any other gas is mixed in the refrigerant, the gas pressure in the refrigeration cycle becomes
abnormally high and it as a result causes pipe burst and injuries on persons.
•Do not modify this unit by removing any of the safety guards or by by-passing any of the
safety interlock switches.
•Exposure of unit to water or other moisture before installation may cause a short-circuit of
electrical parts.
Do not store it in a wet basement or expose to rain or water.
ENGLISH

3
•After unpacking the unit, examine it carefully if there are possible damage.
•Do not install in a place that might increase the vibration of the unit.
•To avoid personal injury (with sharp edges), be careful when handling parts.
•Perform installation work properly according to the Installation Manual.
Inappropriate installation may result in water leakage, electric shock or fire.
•When the air conditioner is installed in a small room, provide appropriate measures to
ensure that the concentration of refrigerant leakage occur in the room does not exceed the
critical level.
•Install the air conditioner securely in a location where the base can sustain the weight
adequately.
•Perform the specified installation work to guard against an earthquake.
If the air conditioner is not installed appropriately, accidents may occur due to the falling unit.
•If refrigerant gas has leaked during the installation work, ventilate the room immediately.
If the leaked refrigerant gas comes in contact with fire, noxious gas may generate.
•After the installation work, confirm that refrigerant gas does not leak.
If refrigerant gas leaks into the room and flows near a fire source, such as a cooking range, noxious gas might
generate.
•Electrical work must be performed by a qualified electrician in accordance with the
Installation Manual. Make sure the air conditioner uses an exclusive power supply.
An insufficient power supply capacity or inappropriate installation may cause fire.
•Use the specified wires for wiring connect the terminals securely fix. To prevent external
forces applied to the terminals from affecting the terminals.
•Conform to the regulations of the local electric company when wiring the power supply.
Inappropriate grounding may cause electric shock.
•Do not install the air conditioner in a location subject to a risk of exposure to a combustible
gas.
If a combustible gas leaks, and stays around the unit, a fire may occur.
1 PRECAUTIONS FOR SAFETY

4
2 SELECTION OF INSTALLATION PLACE
WARNING
•Install the air conditioner where there is sufficient strength to weight of the unit.
If strength is insufficient, the unit may fall down resulting in human injury.
•Perform a specified installation work to guard against an earth quake.
An incomplete installation can cause accidents by the units failing and dropping.
•Install the air conditioner at a height 2.5m or more from the floor.
If you insert your hands or others directly into the unit while the air conditioner operates, it is dangerous
because you may contact with revolving fan or active electricity.
CAUTION
•Do not install the air conditioner in a location subject to a risk of exposure to combustible gas.
Should the combustible gas leak and collect near the unit, fire may occur.
Upon approval of the customer, install the air conditioner in a place that satisfies the
following conditions.
•Place where the unit can be installed horizontally.
•Place where a sufficient servicing space can be ensured for safe maintenance and check.
•Place where drained water will not cause any problem.
Avoid installing in the following places.
•Place exposed to air with high salt content (seaside area), or place exposed to large quantities of sulfide gas
(hot spring). (Should the unit be used in these places, special protective measures are needed.)
•Place exposed to oil, vapor, oil smoke or corrosive gas.
•Place where organic solvent is used nearby.
•Place close to a machine generating high frequency.
•Place near door or window where may come to contact with the outside air of high humidity.
(Dewing may be caused.)
•Place where special spray is frequently used.
•Place with poor ventilation.
Installation space
Keep 5mm or more for clearance between top
plate of the indoor unit and the ceiling surface.
Reserve space required to install the indoor unit
and for service work.
200mm
or more
Ceiling
Ceiling inside height :
200mm or more
1000mm
and more
Refrigerant piping port
1000mm
and more
Obstacle
The lighting term setup of the filter sign (Notification of filter cleaning) of the remote controller can be changed
according to the condition of installation. If the room is not heated due to the installation place or construction of the
room, the detection temperature of heating can be raised.
For setup method, refer to “Change of lighting term of filter sign”and “To secure better effect of heating”in the
Applicable controls of this Manual.

5
Height of ceiling
When height of the ceiling exceeds 3.0m, it is difficult
that the hot air reaches up to the floor surface. In this
case, it is necessary to exchange the motor speed-up
by using a connector, which is attached to the air
conditioner unit.
3 INSTALLATION OF INDOOR UNIT
WARNING
Install the air conditioner certainly to sufficiently withstand the weight.
If the strength is insufficient, the unit may fall down resulting in human injury.
Perform a specified installation work to guard against strong wind or earthquake.
An incomplete installation can cause accidents by the units falling and dropping.
REQUIREMENT
Strictly comply with the following rules to prevent damage of the indoor units and human injury.
•Do not put a heavy article on the indoor unit. (Even units are packaged)
•Carry in the indoor unit as it is packaged if possible. If carrying in the indoor unit unpacked by necessity, be
sure to use buffering cloth, etc. to not damage the unit.
•To move the indoor unit, do not apply force to the refrigerant pipe, drain pan, foamed parts, or resin parts, etc.
•Carry the package by two or more persons, and do not bundle it with band at positions other than specified.
•The hanging bolt pitch on longitudinal direction is not divided at center with the ceiling opening size.
Therefore, check the relational position in the followering figure.
If relational position is incorrect, the check panel cannot be installed.
In case of wireless type
The sensor of indoor unit with wireless remote
controller can receive a signal within approx. 8m.
Based upon it, determine a place where the remote
controller is operated and the installation place of the
indoor unit.
•To prevent a malfunction, select a place where is not
influenced by a florescent light or direct sunlight.
•Two or more (Up to 6 units) indoor units with
wireless remote controller can be installed in the
same room.
Installable height of ceiling
Up to 3.0m
8m or less
2 SELECTION OF INSTALLATION PLACE

6
External view
Panel external dimension A
Panel external dimension 755
Ceiling open dimension 695
655 530
198
130
10
755
96
20 20
30 30
Pitch 200 ×I
1000
or more
(Pipe side)
200 or more
1000 or more
(Air outlet port)
Obstacle
Space necessary for installation and servicing
Ceiling
Ceiling open dimension B
Knockout hole for front blow out Ø150 Knockout hole (For taking in fresh air)
(When take in fresh air, attach a filter,
etc. so that fresh air does not enter directly.)
Y view Z view
30 30
65 125
50 E
H100
60
80
80
1010
100
F
A
G
Ø180
110
Z
Center of panelCD
Y
Refrigerant pipe
connecting port
(Gas side) J
Refrigerant pipe
connecting port
(Liquid side) K
Drain pipe connecting port
(VP25)
Power connecting
port
440
335
255
620
100
120
160
165
Note
When using the discharge divided duct and the duct to take in fresh air,
consult your dealer about availability.
16
120
4
2.7
120
• Wired remote controller
(RBC-AMT21E)
AModel B C D E F G H I J K
1220
1420
AP0151, AP0181
AP0241
1160
1360
545
645
485
585
530
630
470
570
254
460
800
1000
4
5
Ø12.9
Ø15.9
Ø6.4
Ø9.5

7
Ceiling opening and installation of hanging bolts
•Considering pipe/wire connecting work inside the ceiling after the indoor unit has been hanged, select an
installation place and determine piping direction.
•After installation place of the indoor unit has been determined, open the installation hole on the ceiling and install
the hanging bolts.
•For the ceiling opening size and the hanging bolt pitch, refer to the external view and the attached installation
pattern.
•If the ceiling has been already set up, draw the drain pipe, refrigerant pipe, indoor/outdoor inter-unit wire, wire for
central control system, and remote controller wire up to the position where pipes and wires are to be connected
before hanging the indoor unit.
Please procure the hanging bolts and nuts for
installation of the indoor unit at local site.
[How to use the attached installation pattern]
The installation pattern is attached inside of the package cap.
<In case of existing ceiling>
Use the installation pattern for positioning of the ceiling opening hole and the hanging bolt.
<In case of new ceiling>
Use the installation pattern for positioning of the opening hole when setting up a new ceiling.
•Install the indoor unit after installation of the hanging bolts.
•Using the attached installation pattern fixing screws (M5 ×16L:
4 pieces), attach the installation pattern to the indoor unit.
(Screwing to installation brackets of the ceiling panel)
•When setting up the ceiling, open a hole along the outside
dimension of the installation pattern.
Installation of hanging bolts
Use M10 hanging bolts (4 pcs, to be local procure).
Matching to the existing structure, set pitch according to size in the unit external view as shown below.
New concrete slab
Install the bolts with insert brackets or anchor
bolts.
Steel flame structure
Use existing angles or install new
support angles.
Existing concrete slab
Use a hole-in anchors, hole-in
plugs, or a hole-in bolts.
Anchor bolt
(Blade type
bracket) (Slide type bracket) (Pipe hanging anchor bolt)
Reinforcing
steel
Hanging bolt
Hanging bolt Support angle
Installation
pattern
Ceiling panel fixing screw
(Use the attached screws.)
Hanging bolt
Nut
Flat washer
M10 or W3/8
M10 or W3/8
M10
4 pieces
12 pieces
10 pieces
3 INSTALLATION OF INDOOR UNIT

8
Hanging up of unit
CAUTION
This unit is incorporated with drain pump and float switch. Never incline the indoor unit. Otherwise, malfunction
of the float switch may be caused resulting in water leakage.
Adjust nut position (lower side) so that clearance between (lower side) and the lower side of ceiling board is 130mm.
•Hang up the indoor unit by hanging nut of hanging bolt to T groove of hanging bracket of the indoor unit.
•Using the level vial, etc., check that four sides are horizontal. (Horizontal degree : whithin 5mm)
•Using the installation gauge, check and adjust the positional relation between the indoor unit and ceiling opening
hole, and hanging-up height of the indoor unit.
Hanging bolt
Washer
(Upper side)
(Hanging bracket
main unit)
Washer
(Lower side)
Nuts (Lower side)
Nut (Upper side)
130mm
Lower surface of ceiling
Opening part
(Ceiling opening dimension)
(Ceiling opening
dimension)
AP0151, AP0181 : 1160
AP0241 : 1360
50110
695
2020
Outline of indoor unit
Front side
(Piping side)
Indoor unit
Installation gauge
Ceiling board
Rear side
Installation gauge
15
20
50 110
Ceiling board
1
3
2
Check lower side of the indoor unit locates at
position 15mm higher than bottom surface of the
ceiling board. (4 corners)
Check clearance between the side of the indoor unit
and the ceiling board is 20mm. (Both left/right)
Check clearance between the front side (piping
side) of the indoor unit and the ceiling board is
110mm, and clearance between rear side of indoor
unit and the ceiling board is 50mm.
Fix securely
Level vial
•Fix the indoor unit securely by tightening nut at
upper side.
REQUIREMENT
•Using a level vial, etc., confirm the horizontal
level of the indoor unit.
•Tighten the nut sufficiently, and fix it securely.

9
Installation of ceiling panel (Sold separately)
Install the ceiling panel according to Installation Manual after piping/wiring work has completed.
Check that installation of indoor unit and ceiling opening part is correct, and then install it.
REQUIREMENT
Connect the connecting sections of ceiling panel and ceiling surface, and the ceiling panel and indoor unit closely.
If there is clearance, air leakage generates resulting in dewing or water leakage.
Indoor unit
Lower surface
of ceiling
Lower side of
pattern sheet
Indoor unit
Match on the same level.
Protruding : 0mm or more Drawing :3mm or less
Indoor unit
Installation of remote controller (Sold separately)
For installation of the wired remote controller, follow the Installation Manual attached with the remote controller.
For installation of the wireless remote controller, follow to the Installation Manual attached to the remote controller.
•Do not put the remote controller on the place where is exposed to direct sunlight or near a stove, etc.
•Operate the remote controller, check the indoor unit surely receives the signal, and then install the remote
controller. (Wireless type)
•Install the remote controller 1m apart from the devices such as TV or stereo. (Image may be disturbed or noise
may be output.) (Wireless type)
3 INSTALLATION OF INDOOR UNIT

10
4 DRAIN PIPING WORK
REQUIREMENT
•Be sure to perform heat insulation of the drain pipes of the indoor unit.
•Never forget to perform heat insulation of the connecting part with the
indoor unit. An incomplete heat insulation causes dewing.
•Set the drain pipe with downward slope (1/100 or more), and do not
make swelling or trap on the piping. It may cause an abnormal sound.
•For length of the traversing drain pipe, restrict to 20m or less.
In case of a long pipe, provide support brackets with interval of
1.5 to 2m in order to prevent waving.
•Set the collective piping as shown in the right figure.
•Do not mount an air purge pipe,
otherwise drain water spouts
out resulted in water leak.
CAUTION
•Following the Installation Manual,
perform the drain piping work so that
water is properly drained, and apply a
heat insulation so as not to cause a dew.
Inappropriate piping work may result in
water leakage in the room and wet of
furniture.
Pipe material/Insulator and size
The following materials for piping work and insulating
process are procured locally.
Pipe material
Insulator
Hard vinyl chloride pipe VP25
(Outer diameter Ø32mm)
Foamed polyethylene foam, thickness:
6mm or more
Drain up
•If a downward grading (1/100) cannot be secured on
the drain pipe, piping can be performed by rising-up
up to 340mm.
(500mm or less from the bottom surface of the
ceiling).
•Be sure to use the attached drain-up pipes when
performing the drain-up from drain port of the indoor
unit as required, and set the drain-up up to 500mm
or less from the bottom surface of ceiling. Never set
the drain-up below 500mm because it causes a
malfunction.
*1 Use vinyl chloride pipe in when using the drain-
up pipe at a position 500mm below the bottom
surface of the ceiling.
*2 Use the attached vinyl chloride pipe for traversing
piping. (Extension of pipe is disabled at site.)
•After rising up vertically, set the grading downward
immediately.
Trap
Arched
shape
Support
bracket
1/100 or more
downward
Heat
insulator
1.5m to 2m
As long as possible (10cm)
VP30 or more Downward slope
1/100 or more
VP25
VP25
VP25
(Collective pipes)
1
VP16
VP25
Extension
disabled
*
2 (140)
*
1
Below 500
Heat insulating of pipe connecting part
•Be sure to apply heat insulating securely to the pipe
connecting part.
•Be sure to tape surely the butting part of the heat
insulator at the main unit side and at site so that no
clearance generates.
Butt heat insulator
without clearance.
Heat insulator
(Required at site) Using tape,
fix the heat insulator.
Heat insulator
(Indoor unit side)
Hard vinyl
chloride pipe
(Required at site)

11
Check the draining
After drain piping work, check that water drain is
properly performed and water does not leak from the
connecting part of the pipes. In this time, check also
there is no abnormal sound of the motor of the drain
pump. Be sure to check draining when installed in the
heating period.
Using a hose or a pitcher, enter 600cc-water gradually
into the air outlet taking precautions against water
splash on the motor of the drain pump.
Float switch lead
CN030 connector
Electric parts box
Single phase 220-240V, 50Hz
220V, 60Hz
R(L) S(N)
Float switch connector (3P, Red)
(Lead wire color:Black)
When finish the check of float switch by pull-out the
connector, securely insert as it was before.
Main control P.C. board
CN030
When the electric work has finished:
•Before installing a panel, pour water, check water is drained from the drain pipe in COOL mode, and then check
there is no water leak from the drain pipes.
When the electric work has not finished:
•Pull out the float switch connector from P.C. board connector (CN030: Red) of the electric parts box.
(In this time, be sure to check the power is turned off.)
•Connect the single-phase 220-240V 50Hz (or 220V 60Hz) power to the terminal blocks R (L) and S (N).
(Never apply 220-240V to (A), (B), (U1),and (U2), otherwise a trouble of P.C. board occurs.)
•When the power is turned on, the drain pump motor drives automatically. Check water is drained from the drain
pipe, and then check there is no water leak from the drain pipes.
•After check of draining and water leak, turn off the power supply, attach the float switch connector to the original
position (CN030) of P.C. board, and then set the electric parts box as before.
Pitcher
Air outlet
REQUIREMENT
•Using adhesive agent for vinyl chloride, connect the hard vinyl chloride pipes certainly so that water does not leak.
•It requires several times to dry and harden the adhesive agent.
(Refer to Guide Manual of the adhesive agent.) In this time, be sure not to apply force to the connecting
section with the drain pipes.
4 DRAIN PIPING WORK

12
5 REFRIGERANT PIPING
WARNING
•If refrigerant gas has leaked during the installation work, ventilate the room immediately.
•If the leaked refrigerant gas comes in contact with fire, noxious gas may generate.
•After the installation work, confirm that refrigerant gas does not leak.
•If refrigerant gas leaks into the room and flows near a fire source, such as a cooking range, noxious gas may
generate.
REQUIREMENT
When the refrigerant pipe is long, set the support brackets to fix the pipe with 2.5 to 3m intervals. If the pipe is
not fixed, abnormal sound may generate.
Be sure to use the flare nuts attached to the indoor unit or those fro R410A.
Permissible pipe length and permissible height difference
They are different according to the used outdoor unit. For details, refer to the Installation Manual attached to the
outdoor unit.
Piping material and dimensions
Piping material
Model MMU-
Pipe size (mm) Gas side
Liquid side
Phosphor deoxidization joint-less pipe for air conditioner
AP0151SH , AP0181SH AP0241SH
Ø12.7 Ø15.9
Ø6.4 Ø9.5
+0
- 0.4
•Use a clean and new pipe, and check that impurity such as dust, oil, moisture, etc. does not adhere in the pipe.
Pipe Forming/End Positioning
Flaring
1. Cut the pipe with a pipe cutter.
2. Insert a flare nut into the pipe, and flare the pipe.
As the flaring sizes of R410A differ from those of
refrigerant R22, the flare tools newly manufactured
for R410A are recommended.
However, the conventional tools can be used by
adjusting projection margin of the copper pipe.
•Flaring diam. meter size : A (Unit : mm)
Outer diam. of copper pipe
6.4
9.5
12.7
15.9
A
R410A
9.1
13.2
16.6
19.7
*In case of flaring for R410A with the conventional
flare tool, pull it out approx. 0.5 mm more than that
for R22 to adjust to the specified flare size.
The copper pipe gauge is useful for adjusting
projection margin size.
90˚ Obliquity Roughness Warp
A

13
•Projection margin in flaring :
B (Unit : mm)
Rigid (Clutch type)
Outer diam. of
copper pipe
6.4
9.5
12.7
15.9
R410A tool used
R410A R22
0 to 0.5 (Same as left)
0 to 0.5 (Same as left)
0 to 0.5 (Same as left)
0 to 0.5 (Same as left)
Conventional tool used
R410A R22
1.0 to 1.5 0.5 to 1.0
1.0 to 1.5 0.5 to 1.0
1.0 to 1.5 0.5 to 1.0
1.0 to 1.5 0.5 to 1.0
Imperial (Wing nut type)
Outer diam. of copper pipe
6.4
9.5
12.7
15.9
R410A R22
1.5 to 2.0 1.0 to 1.5
1.5 to 2.0 1.0 to 1.5
2.0 to 2.5 1.5 to 2.0
2.0 to 2.5 1.5 to 2.0
Connection of refrigerant pipe
Connect all the refrigerant pipes with flare connecting
work.
•Since the atmospheric pressure only is sealed
as the sealing gas, it is not abnormal that
“Pushu…” sound is not heard when the flare
nut is removed.
•Be sure to use a double spanner for pipe
connecting work of the indoor unit.
•Refer to the following table for tightening torque.
Airtight test/Air purge, etc.
For airtight test, air purge, addition of refrigerant, and
gas leak check, follow the Installation Manual attached
to the outdoor unit.
REQUIREMENT
Be sure to use the tool such as charge hose
exclusive to R410A.
Do not turn on the power until the airtight test and
the vacuuming have finished. (If turning on the
power, the incorporated PMV is closed fully and the
period until the vacuuming finishes elongates.
Open fully valves of the outdoor unit
Gas leak check
Check with a leak detector or soap water whether gas
leaks or not, from the pipe connecting section or cap of
the valve.
REQUIREMENT
Use a leak detector manufactured exclusively for
HFC refrigerant (R410A, R134a, etc.).
Heat insulating process
Perform heat insulating for pipes at liquid side and gas
side separately.
In cooling time, temperature at both liquid and gas sides
becomes lower.
Therefore, perform heat insulating process sufficiently
to avoid dewing.
•For heat insulator of pipe at gas side, be sure to use
one with heat-resisting temp.120°C or more.
•Using the attached heat insulating pipe, perform heat
insulating process securely for pipe connecting part of
the indoor units without clearance.
REQUIREMENT
Apply the thermal insulation to the pipe connecting
section of the indoor unit securely up to the root
without exposure of the pipe.
(The pipe exposed to the outside causes water leak.)
Work using double spanner
Connecting pipe
outer dia. (mm)
Ø6.4
Ø9.5
Ø12.7
Ø15.9
Tightening torque
(N•m)
14 to 18 (1.4 to 1.8 kgf•m)
33 to 42 (3.3 to 4.2 kgf•m)
50 to 62 (5.0 to 6.2 kgf•m)
68 to 82 (6.8 to 8.2 kgf•m)
Re-tightening
torque (N•m)
18 (1.8 kgf•m)
42 (4.2 kgf•m)
50 (5.0 kgf•m)
68 (6.8 kgf•m)
Set notching upward.
Main unit Pipe side
(Required at the site)
Attached heat insulating pipe
5 REFRIGERANT PIPING
B

14
6 ELECTRIC WORK
WARNING
1. Using the specified wires, ensure to connect the wires, and fix wires securely so that the
external strength of the wires do not transmit to the connecting part of the terminals.
Incomplete connection or fixation may cause a fire, etc.
2. Be sure to connect earth wire. (Grounding work)
Do not connect the earth wire to gas pipe, city water pipe, lightning rod, or the earth wire of
telephone.
Incomplete grounding causes an electric shock.
3. For electric work, strictly follow to the Local Regulation in each country and the Installation
Manual, and use an exclusive circuit.
Capacity shortage of power circuit or incomplete installation may cause an electric shock or a fire.
CAUTION
Be sure to install an earth leakage breaker.
If an earth leakage breaker is not installed, an electric shock may be caused.
REQUIREMENT
•For power supply wiring, strictly conform to the Local Regulation in each country.
•For wiring of power supply of the outdoor units, follow to the Installation Manual of each outdoor unit.
•Never connect 220–240V power to the terminal blocks (A, B, U1, U2, X, Y, etc.) for control wiring.
(Otherwise, the system will be failed.)
•Perform the electric wiring so that it does not come to contact with the high-temperature part of the pipe.
The coating may melt resulted in an accident.
•After connecting wires to the terminal blocks, provide a trap and fix wires with the wire clamp.
•Store the refrigerant piping line and control wiring line in the same line.
•Do not turn on the power of the indoor unit until vacuuming of the refrigerant pipes completes.

15
Power supply specifications
Power supply cord and communication wires are procured locally.
For the power supply specifications, follow to the table below. If capacity is little, it is dangerous because overheat or
seizure may be caused.
For specifications of the power capacity of the outdoor unit and the power supply wires, refer to the Installation
Manual attached to the outdoor unit.
Indoor unit power supply (*1)
•For the power supply of the indoor unit, prepare the exclusive power supply separated from that of the outdoor unit.
•Arrange the power supply, earth leakage breaker, and main switch of the indoor unit connected to the same
outdoor unit so that they are commonly used.
•Power supply cord specification : Cable 3-core 2.5mm², in conformity with Design 60245 IEC 57.
Indoor/Outdoor inter-unit wiring, Central controller wiring (*2) (*3)
•2-core with polarity wires are used for the Indoor/Outdoor inter-unit wiring and Central controller wiring.
•To prevent noise trouble, use 2-core shield wire.
•The length of the communication line means the total length of the inter-unit wire length between indoor and
outdoor units added with the central control system wire length.
Remote controller wiring (*4)
•2-core with non-polarity wire is used for wiring of the remote controller wiring and group remote controllers wiring.
Twist wire: 0.5mm2to 2.0mm2× 2
Total wire length of remote controller
wiring and remote controller inter-unit
wiring = L + L1 + L2 + …Ln
In case of wired type only
In case of wireless type included
Remote controller wiring, remote
controller inter-unit wiring
CAUTION
The remote controller wire
(Communication line) and
AC220–240V wires cannot be
parallel to contact each other and
cannot be stored in the same
conduits. If doing so, a trouble
may be caused on the control
system due to noise, etc.
Total wire length of remote controller inter-unit wiring = L1 + L2 + …Ln
Power supply (*1)
Communication line
220–240V ~50Hz
220V ~60Hz
Twist wire : 2.0 mm²
Twist wire : 3.5 mm²
(Up to 1000m) Twist wire : 1.25 mm²
(Up to 2000m) Twist wire : 2.00mm²
(Up to 1000m) Twist wire : 1.25 mm²
(Up to 2000m) Twist wire : 2.00mm²
Twist wire : 0.5 to 2.0 mm²
Power supply
Power supply wiring
Indoor/Outdoor inter-unit wiring (*2)
(2 cables)
Central control line wiring (*3)
(2 cables)
Remote controller wiring (*4)
(2 cables)
Below 20m
Below 50m
Wire size
Wire size
Wire size
Up to 500m
Up to 400m
Up to 200m
Remote controller inter-unit wiring
Indoor unit
Remote
controller
Indoor unit
L1 L2 Ln
(Max. 8 units)
Indoor unit Indoor unit
Remote
controller
wiring
6 ELECTRIC WORK
Power supply switch/Earth leakage breaker or power supply wiring/fuse rating for
indoor units should be selected by the accummulated total current values of the indoor units.

16
Cable connection
REQUIREMENT
•As the remote controller cable has no polarity, there is no problem if connections to indoor unit terminal blocks
A and B are reversed.
•Be sure to pass the cable through the bushing of cable connection port of the indoor unit.
•Keep a margin (approx. 100m) on a cable to hang down the electric parts box at servicing, etc.
•The low-voltage circuit is provided for the remote controller. (Do not connect high-voltage circuit.)
<END unit>
(R (L), S (N) terminal) Indoor unit power supply
(U1, U2terminal) Control transmission line
(A, B terminal) Remote controller wirng
<Intermediate unit>
Treating of wiring connecting port
•As shown on the figure, seal the wire connecting port with heat
insulator.
If sealing is insufficient, dewing is caused in the electric parts box.
•Remove the cover of the electric parts box.
•Tighten the screws of the terminal block, and fix the
cables with cord clamp attached to the electric parts
box. (Do not apply tension to the connecting section
of the terminal block.)
•Mount the cover of the electric parts box without
pinching cables.
Using the attached thermal insulator for sealing of
cable connecting port, seal the cable connecting
port. (Otherwise dewing may be caused.)
R
(L) S (N)
10
10
30
70
Earth line
Connecting cable
Cable Heat insulator
(Required at site)
Electric parts box
Cord clamp
Earth screw
Power supply cable
Inter-unit wire
R(L)
R(L)
S(N)
S(N)
U 1 U 2 AB
U
1 U 2 AB
Earth screw

17
Remote controller wiring
•Strip off approx. 14mm cover of the wire to be connected.
•Twist wire of the remote controller to be connected with wire of the remote controller unit (or sensor), and press-fit
them with a wire joint. (Wire joints (White: 2 pieces) are included in the accessory of the main remote controller
(sold separately) or wireless remote controller kit (sold separately).)
•As the remote controller wire has no polarity, there is no problem if connections to indoor unit terminal blocks A
and B are reversed.
<Wiring diagram>
Wiring between indoor and outdoor units
NOTE
An outdoor unit connected
with indoor/outdoor inter-unit
wire becomes automatically
the header unit.
Address setup
Set up the addresses according to the Installation Manual attached to the outdoor unit.
Wiring of ceiling panel
Following to the Installation Manual of the ceiling panel, connect the connector.
<In case of installation to high ceiling>
When installing an indoor unit a high ceiling with height from
3m to 3.8m, remove the connector of the motor lead wire and
connect the motor speed-up connector attached to the air
conditioner to the middle position.
Terminal block
for remote controller
wiring of indoor unit
A
B
Approx. 200mm W :White
B : Black
W
B
Remote controller wire
(Local procure) Wire from remote controller unit or sensor
Connecting
part
Remote
controller unit
or sensor part
Wire from remote
controller or sensor
Remote controller wiring
Wire joint
Header unit Follower unit
Earth leakage breaker
Earth leakage breaker
Switch
(Earth)
(Open)
Earth
Outdoor power supply
3-phase
380–415V, 50Hz
380V, 60Hz
Central control line wire
Power supply
220–240V ~50Hz
220V ~60Hz
Remote controller,
for central control, etc.
Connection of shield
wire closed terminal
Inter-unit wire between outdoor units
Indoor/Outdoor inter-unit wire
Indoor power supply
220–240V ~50Hz
220V ~60Hz
(Earth)
Connection of shield
wire closed terminal
(Remote controller group operation)
Pull box
Indoor unit
Motor speed-up connector
Remove
Motor side
Electric
parts box side
6 ELECTRIC WORK