Toshiba RAS-10N4KVRG-UA User manual

1129850207
OWNER’S MANUAL
AIR CONDITIONER (SPLIT TYPE)
For general public use
Indoor unit
RAS-10, 13, 16N4KVRG-UA
Outdoor unit
RAS-10, 13, 16N4AVRG-UA
ENGLISHENGLISH
R32
УКРАЇНСЬКА
Book_1129850207_EN - UA.indb 1Book_1129850207_EN - UA.indb 1 18/3/2564 BE 10:4618/3/2564 BE 10:46

PRECAUTIONS FOR SAFETY
Read the precautions in
this manual carefully before
operating the unit.
This appliance is filled with R32.
●Keep this manual where the operator can easily find it.
●Read the precautions in this manual carefully before operating the unit.
●This appliance is intended to be used by expert or trained users in shops, in light
industry and on farms, or for commercial use by lay persons.
●The precautions described herein are classified as DANGER, WARNING and
CAUTION. They both contain important information regarding safety. Be sure to
observe all precautions without fail.
DANGER
●Do not install, repair, open or remove the cover. It may expose you to
dangerous voltages. Ask the dealer or the specialist to do this.
●Turning off the power supply will not prevent potential electric shock.
●The appliance shall be installed in accordance with national wiring regulation.
●Means for disconnection from the supply having a contact separation of at least
3 mm in all poles must be incorporated in the fixed wiring.
●The appliance must be stored in a room without continuously operating ignition
sources (for example, open flames, an operating gas appliance or an operating
electric heater).
●In order to avoid fire, explosion or injury, do not operate the unit when harmful
gases (e.g. flammable or corrosive) are detected near the unit.
WARNING
●Do not expose your body directly to cool or warm air for a long time.
●Do not insert your finger or any article into the air inlet/outlet.
●When an abnormality (burning smell, etc.) occurs, stop the air conditioner and
disconnect the power supply or turn off the breaker.
●This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
●This appliance is not intended for use by person (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
●The air conditioner must be installed, maintained, repaired and removed by a
qualified installer or qualified service person. When any of these jobs is to be
done, ask a qualified installer or qualified service person to do them for you.
●Children should be supervised to ensure that they do not play with the
appliance.
Book_1129850207_EN - UA.indb 2Book_1129850207_EN - UA.indb 2 18/3/2564 BE 10:4618/3/2564 BE 10:46

PRECAUTIONS FOR SAFETY
●Do not use any refrigerant different from the one specified (R32) for
complement or replacement. Otherwise, abnormally high pressure may be
generated in the refrigeration cycle, which may result in a failure or explosion of
the product or an injury to your body.
●Do not use means to accelerate the defrosting process or to clean, other than
those recommended by the manufacturer.
●The appliance shall be stored in a room without continuously operating ignition
sources (for example: open flames, an operating gas appliance or an operating
electric heater).
●Be aware that refrigerants may not contain an odour.
●Do not pierce or burn as the appliance is pressurized. Do not expose the
appliance to heat, flames, sparks, or other sources or ignition. Else, it may
explode and cause injury or death.
CAUTION
●Do not wash the unit with water. It may cause an electric shock.
●Do not use this air conditioner for other purposes such as preserving food,
breeding animal, etc.
●Do not step or put anything on the indoor/outdoor unit. It may cause an injury or
damage the unit.
●Do not touch aluminium fin because it may cause an injury.
●Before cleaning the unit, turn off the main switch or the circuit breaker.
●When the unit won’t be used for a long time, turn off the main switch or the
circuit breaker.
●It is recommended that maintenance be performed by a specialist when the unit
has been operated for a long time.
●The manufacturer shall not assume any liability for the damage caused by not
observing the description of this manual.
●Remote controller and Holder are contained with magnet please keep far from
product that effect with magnet (such as electronics appliance magnetic strip
card and etc.)
●High temperature, high magnet field and direct force collisions may effect to
magnet force down.
EN
Book_1129850207_EN - UA.indb 3Book_1129850207_EN - UA.indb 3 18/3/2564 BE 10:4618/3/2564 BE 10:46

INDOOR UNIT DISPLAY
1
AIR FLOW DIRECTION
3
AUTOMATIC OPERATION
6
To automatically select cooling, heating, or fan only operation
1. Press
MODE
MOD
: Select Auto A.
2. Press : Set the desired temperature. Min. 17°C, Max. 30°C.
3. Press FAN
FAN
: Select AUTO, LOW , LOW+ , MED ,
MED+ , HIGH or Quiet
1. Press
MODE
MOD
: Select Cool , or Fan only .
2. Press : Set the desired temperature. Min. 17°C, Max. 30°C.
Fan Only: No temperature indication
3. Press FAN
FAN
: Select AUTO, LOW , LOW+ , MED ,
MED+ , HIGH or Quiet
DRY OPERATION
8
For dehumidification, a moderate cooling performance is controlled
automatically.
1. Press
MODE
MOD
: Select Dry .
2. Press : Set the desired temperature. Min. 17°C, Max. 30°C.
Note: DRY mode fan speed is set to Auto only.
HEATING and 8°C OPERATION
7
1. Press
MODE
MOD
: Select Heat .
2. Press
: Set the desired temperature. Min = 5°C, Max = 30°C.
* Temperature range 5-16°C is Heat mode with 8°C operation with less of
energy usage
3. Press FAN
FAN
: Select AUTO, LOW , LOW+ , MED ,
MED+ , HIGH or Quiet
Note: During 8 °C mode active (temperature range 5-16°C), some operation
such as QUIET, Hi POWER, TIMER OFF cannot use.
1
Press FIX
FIX
: Move the
louver in the desired vertical
direction.
2
Press FIX
FIX
: Move the
louver in the desired horizontal
direction.
3
V
V
H
H
H.DA
Swing off
Vertical
(Up-Down)
Swing
Vertical and
Horizontal
Swing
Horizontal
(Left-Right)
Swing
HADA CARE
FLOW
SWING operation can be
selected from MENU button
MENU
MEN
●Vertical (Up-Down) swing
●Horizontal (Left-Right) swing
●HADA Care flow
Note:
●Do not move the louver manually by hands or others.
●The louver may automation positioning by some operation mode.
●Display brightness can be adjusted, follow procedure on ".
1ECO (White)
2Wi-Fi access (White)
3PURE (White)
4Timer (White)
5Operation Mode
- Cool (Blue)
- Heat (Orange)
Preparing Filters
1. Open the air inlet grille and remove the air filters.
2. Attach the filters. (see detail in the Installation Manual).
Loading Batteries (when use wireless operation.)
1. Remove the slide cover.
2. Insert 2 new batteries (AAA type)
following the (+) and (–) positions.
Remote Control Reset
1. Remove the batteries.
2. Press .
3. Insert the batteries.
PREPARATION BEFORE USE
2
REMOTE CONTROL
4
1Infrared signal emitter
2Start/Stop button
3Mode select button
4Temperature button
5Fan speed button
6Menu select button
7Set louver Up-Down button
8
Set louver Left-Right button
9Check button*
*Check button under battery cover
FIX
MODE
FAN MENU
FIX
FIX
FIX
FAN
MEN
MOD
2
1
4
6
8
3
5
7
9
COOLING / FAN ONLY OPERATION
5
Book_1129850207_EN - UA.indb 4Book_1129850207_EN - UA.indb 4 18/3/2564 BE 10:4618/3/2564 BE 10:46

MENU SETUP
9
For select more setting of Air conditioner such as Louver select, Hi Power,
OFF Timer and other use MENU button MENU
MEN
FIX
MODE
FAN MENU
FIX
FIX
FIX
FAN
MEN
MOD
9.1 LOUVER SWING and HADA CARE FLOW OPERATION
Comfortable air flow can select from feature.
Louver swing opearation:
●To distribute air flow in both vertical and horizontal by swing the louver
automatically.
HADA care flow operation:
●Air flow upward to the ceiling, provide Indirect air flow to body and
homogenize room temperature.
Note:
●During HADA CARE FLOW mode, FIX button cannot active.
Louver Swing and HADA Care Flow Operation Setting
1. Press MENU button for enter menu selection
MENU
MEN
°C
Blink
During triangle mark blink can select menu by press TEMP. button.
2. Enter Louver set by press MENU button again.
triangle mark will stop blink and setting feature will be blink instead.
°C
Blink
MENU
MEN
3. Select Louver swing or HADA CARE FLOW by press TEMP. button.
°C
V
V
HH
H.DA
Swing
off
Vertical
(Up-Down)
Swing
Vertical and
Horizontal
Swing
Horizontal
(Left-Right)
Swing
HADA CARE FLOW
4. Confirm selected feature by press MENU button again.
MENU
MEN
°C
When feature had selected will return to menu selection display triangle mark
will blink .
5. Leave from menu setting display by select exit and press menu button
MENU
MEN
°C
°C
Leave from menu setting to normal display (no triangle and feature blink).
EN
Book_1129850207_EN - UA.indb 5Book_1129850207_EN - UA.indb 5 24/3/2564 BE 10:3424/3/2564 BE 10:34

9.2 SILENT OPERATION (Outdoor Unit)
Keep outdoor unit operating silently to ensure either yourself or neighborhood
will have a tight sleep in nighttime. By this feature, the heating capacity will
be optimized to deliver such silent experience. The silent operation can be
selected from one of two purposes (Silent 1 and Silent 2).
There are three setting parameters: Standard level > Silent 1 > Silent 2
Silent 1:
●Though operating silently, the Heating (or Cooling) capacity is still prioritized
to ensure having sufficient comfort inside the room.
●This setting is a perfect balance between the Heating (or Cooling) capacity
and the Sound level of outdoor unit.
Silent 2:
●Compromising the Heating (or Cooling) capacity to the Sound level in any
circumstance where the outdoor unit’s sound level is highly prioritized.
●This setting has a purpose to reduce the maximum sound level of outdoor
unit by 4 dB(A).
Note:
●While activating of Silent operation, inadequate heating (or cooling) capacity
may occur.
Silent Operation Setting
1. Press MENU button for enter menu selection
MENU
MEN
°C
Blink
During triangle mark blink can select menu by press TEMP. button.
°C
Blink both triangle and
feature mark
Feature not yet set
2. Enter SILENT set by press MENU button.
triangle mark will stop blink and setting feature will be blink instead.
°C
MENU
MEN
3. Select SILENT operation by press TEMP. button.
°C
SILENT#1 SILENT#2 None
4. Confirm selected feature by press MENU button again.
MENU
MEN
°C
Blink only triangle
Feature already set
When feature had selected will return to menu selection display triangle mark
will blink
5. Leave from menu setting display by select EXIT.
MENU
MEN
°C
9.3 Hi POWER OPERATION Hi-P
To automatically control room temperature and airflow for faster cooling or
heating operation (except in DRY and FAN ONLY mode)
1. Press MENU button for enter menu setting and press TEMP. button to
select Hi POWER
MENU
MEN
°C
Blink both triangle and
feature mark Feature not
yet set
2. Confirm selected feature by press MENU button again.
MENU
MEN
°C
Blink only triangle Feature
already set
3. Leave from menu setting display by select EXIT.
°C
9.4 ECO OPERATION
ECO
To automatically control room temperature to save energy
(except in DRY and FAN ONLY mode)
1. Press MENU button for enter menu setting and press TEMP. button to
select ECO
MENU
MEN
°C
Blink both triangle and
feature mark
Feature not yet set
2. Confirm selected feature by press MENU button again.
MENU
MEN
°C
Blink only triangle
Feature already set
3. Leave from menu setting display by select EXIT.
MENU
MEN
°C
Note:
●Cooling operation; the set temperture will increase automatically
1 degree/hour for 2 hours (maximum 2 degrees increase).
For heating operation the set temperature will decrease.
Book_1129850207_EN - UA.indb 6Book_1129850207_EN - UA.indb 6 18/3/2564 BE 10:4618/3/2564 BE 10:46

9.5 FIREPLACE OPERATION
Keep indoor unit’s fan blowing continuously during thermo off, to circulate
heat from other sources over the room. There are three setting parameters:
Default setting > Fireplace 1 > Fireplace 2
Fireplace 1:
●During thermo off period, the indoor unit’s fan will continue to run by the
same speed, previously selected by end-user.
Fireplace 2:
●During thermo off period, the indoor unit’s fan will continue to run at
super-low speed, programmed from factory.
Fireplace Operation Setting
1. Press MENU button for enter menu setting and press TEMP. button to
select FIREPLACE
MENU
MEN
°C
Blink both triangle and feature mark
Feature not yet set
2. Enter FIREPLACE set by press MENU button.
triangle mark will stop blink and setting feature will be blink instead.
MENU
MEN
°C
3. Select FIREPLACE operation by press TEMP. button.
°C
FIREPLACE 1 FIREPLACE 2 None
4. Confirm selected feature by press MENU button again.
MENU
MEN
°C
Blink only triangle
Feature already set
When feature had selected will return to menu selection display triangle mark
will blink
5. Leave from menu setting display by select EXIT.
MENU
MEN
°C
Note:
●While Fireplace operation on heating mode, indoor unit fan always runs and
cold air breezing might be occurred.
●Fireplace will operate in Heating mode only.
9.6 TIMER OFF OPERATION
To set the timer OFF when the air conditioner is operating.
1. Press MENU button for enter menu setting and press TEMP. button to
select TIMER OFF.
MENU
MEN
°C
Blink both triangle and feature mark
Feature not yet set
2. Enter TIMER set by press MENU button.
triangle mark will stop blink and setting feature will be blink instead.
MENU
MEN
3. Select TIMER OFF by press TEMP. button.
Can select TIMER OFF from 0.5 - 12hrs.
4. Confirm TIMER OFF by press MENU button.
MENU
MEN
°C
Blink only triangle
Feature already set
5. Leave from menu setting display by select EXIT.
MENU
MEN
°C
Note:
●The setting will be saved for the next same operation.
Cancel TIMER OFF
6. During TIMER OFF already set (no.5) press MENU button and press
TEMP. button to select TIMER OFF.
MENU
MEN
°C
Blink only triangle
Feature already set
7. Press MENU button again will cancel TIMER OFF.
MENU
MEN
°C
Blink both triangle and feature mark
Feature not yet set
8. Leave from menu setting display by select EXIT.
MENU
MEN
°C
EN
Book_1129850207_EN - UA.indb 7Book_1129850207_EN - UA.indb 7 18/3/2564 BE 10:4618/3/2564 BE 10:46

9.7 PLASMA ION OPERATION
PURE
Capture efficiency of floating impurities in the air is accelerated by plasma ion
contaminates such as bacteria, odor, smoke, dust and virus are caught and
deactivated by Plasma Ion.
1. Press MENU button for enter menu setting and press TEMP. button to
select PURE
MENU
MEN
°C
Blink both triangle and feature mark
Feature not yet set
2. Confirm selected feature by press MENU button again.
MENU
MEN
°C
Blink only triangle
Feature already set
3. Leave from menu setting display by select EXIT.
MENU
MEN
°C
Note:
●Plasma Ion operation dose not remove harmful substances from cigarette
smoke (carbon monoxide etc.). Open a window occasionally for ventilation.
9.8 POWER-SELECTION OPERATION
This function is used when the circuit breaker is shared with other electrical
appliances. It limits the maximum current and power consumption to 100%,
75%, or 50% and can be implemented by POWER-SELECTION. The lower
percentage, the higher saving and also longer compressor lifetime.
Notes :
●Due to the reason that POWER-SELECTION function limits the maximum
current, inadequate cooling or heating capacity may occur.
1. Press MENU button for enter menu setting and press TEMP. button to select
POWER-SEL
Blink only triangle
MENU
MEN
°C
2. Enter POWER-SEL setting by press MENU button again.
MENU
MEN
°C
3. Select POWER-SEL level by press TEMP. button.
°C
100% 75% 50%
4. Confirm POWER-SEL level by press MENU button.
MENU
MEN
°C
5. Leave from menu setting display by select EXIT.
MENU
MEN
°C
MANUAL DEFORST OPERATION
10
To defrosting the heat exchanger of the outdoor unit during Heating operation
Press and hold MENU
MEN
: for 5 seconds , then remote control display will
show as picture 1for 2 seconds.
1
DISPLAY LAMP BRIGHTNESS ADJUSTMENT
11
To decrease the display lamp brightness or turn it off.
1. Press and hold FA N
FAN
for 3 seconds until brightness level ( , ,
or ) is shown on remote control LCD then release the button.
2. Press Rise or
Decrease
to adjust brightness in 4 levels.
Remote control
LCD Operation display Brightness
Lamp illuminates full brightness.
100%
Lamp illuminates 50% brightness.
50%
Lamp illuminates 50% brightness and the
operation lamp is turned off.
50%
All lamps are turned off.
All turned off
●
In the examples of and , the lamp illuminates for 5 seconds before going off.
AUTO RESTART FUNCTION SETTING
12
This product is designed so that, after a power failure, it can restart automatically
in the same operating mode as before the power failure.
Information
The product was shipped with Auto Restart function in the OFF position.
Turn it ON as required.
How to turn ON the Auto Restart Function
●Press and hold the [OPERATION] button on the indoor unit for 3 seconds
(3 beep sounds and OPERATION lamp blink 5 time/sec for 5 seconds).
How to turn OFF the Auto Restart Function
●Press and hold the [OPERATION] button on the indoor unit for 3 seconds
(3 beep sounds but OPERATION lamp does not blink).
Notes :
●In case of ON timer or OFF timer are set, AUTO RESTART OPERATION
does not activate.
SELF CLEANING OPERATION
(COOL AND DRY OPERATION ONLY)
13
To protect bad smell caused by the humidity in the indoor unit.
1. If the button is pressed once during “Cool” or “Dry” mode,
the fan will continue to run for other 30 minutes, then it will turn off
automatically. This will reduce the moisture in the indoor unit.
2. To stop the unit immediately, press the more 2 times within 30
seconds.
Book_1129850207_EN - UA.indb 8Book_1129850207_EN - UA.indb 8 18/3/2564 BE 10:4618/3/2564 BE 10:46

TEMPORARY OPERATION
14
In case of the misplaced or discharged remote control
●Pressing the RESET button, the unit can start
or stop without using the remote control.
●Operation mode is set on AUTOMATIC
operation, preset temperature is 24°C and fan
operation is automatic speed.
OPERATION / RESET Button
REMOTE CONTROL A-B SELECTION
15
To separate using of remote control for each indoor unit in case of 2 air
conditioners are installed nearly.
Remote Control B Setup.
1. Press RESET button on the indoor unit to turn the air conditioner ON.
2. Point the remote control at the indoor unit.
3. Push and hold button on the back side of Remote Control “00” will be
shown on the display. (Picture 1)
4. Press
MODE
MOD
during pushing . “B” will show on the display and
“00” will disappear and the air conditioner will turn OFF. The Remote
Control B is memorized. (Picture 2)
Note: 1. Repeat above step to reset Remote Control to be A.
2. Remote Control A has not “A” display.
3. Default setting of Remote Control from factory is A.
12
OPERATION AND PERFORMANCE
16
1. Three-minute protection feature: To prevent the unit from being activated
for 3 minutes when suddenly restarted or switched to ON.
2. Preheating operation: Warm up the unit for 5 minutes before the heating
operation starts.
3. Warm air control: When the room temperature reaches the set temperature,
the fan speed is automatically reduced and the outdoor unit will stop.
4. Automatic defrosting: Fans will stop during defrost operation.
5. Heating capacity: Heat is absorbed from outdoors and released into
the room. When the outdoor temperature is too low, use another
recommended heating apparatus in combination with the air conditioner.
6. Consideration for accumulated snow: Select the position for outdoor unit
where it will not be subjected to snow drifts, accumulation of leaves or
other seasonal debris.
7. Some minor cracking sound may occur when unit operating. This is normal
because the cracking sound may be caused by expansion/contraction of plastic.
Note: Item 2 to 6 for Heating model
Air conditioner operating conditions
Temp.
Operation
Outdoor Temperature Room Temperature
Heating –15°C ~ 24°C Less than 28°C
Cooling –15°C ~ 46°C 21°C ~ 32°C
Dry –15°C ~ 46°C 17°C ~ 32°C
Firstly, turn off the circuit breaker.
Indoor Unit and Remote Control
●
Clean the indoor unit and the remote control with a wet cloth when needed.
●No benzine, thinner, polishing powder or chemically-treated duster.
Air filters
Clean every 2 weeks.
1. Open the air inlet grille.
2. Remove the air filters.
3. Vacuum or wash and then dry them.
4. Reinstall the air filters and close the air inlet grille.
MAINTENANCE
17
The unit does not operate. Cooling or Heating is abnormally low.
●The power main switch is
turned off.
●The circuit breaker is activated
to cut off the power supply.
●Stoppage of electric current
●ON timer is set.
●The filters are blocked with dust.
●
The temperature has been set improperly.
●The windows or doors are opened.
●The air inlet or outlet of the outdoor
unit is blocked.
●The fan speed is too low.
●The operation mode is FAN or DRY.
●POWER SELECTION function is
set 75% or 50% (This function is
depend on remote controller).
TROUBLESHOOTING (CHECK POINT)
18
EN
Book_1129850207_EN - UA.indb 9Book_1129850207_EN - UA.indb 9 18/3/2564 BE 10:4718/3/2564 BE 10:47

WIRELESS LAN CONNECTION
19
Toshiba Home AC Control
Please visit the application store on your device to download and install
Toshiba Home AC Control application.
Register process
Open an application and follow register for User registration.
1Tab Register
5Enter password by 6-10
characters, combination of
alphabet and number
2Enter email address
6Check for term and condition
3Select country
7Confirm information
4Enter user name
8Information will be submitted
to email, click link to confirm
Application
Keyword : Toshiba Home AC Control Android : Version 5.0 or later.
iOS : 9.0 or later.
About Toshiba Home AC Control
1. Toshiba Home AC Control can control AC operation by Smartphone or
tablet (mobile device) via internet connection.
2. Everywhere control, control software run on Cloud system and mobile
device can set and monitor AC operation via internet connection.
3.
Everyone can control, 1 Wireless adapter maximum 5 User
(use 1 email register).
4. Multi AC system control, 1 user can control 10 AC.
5. Group control.
5.1 Can create and control 3 groups of AC.
5.2 Can control max 10 AC per group.
Note:
1. Adapter can register only 1 email address, if register with new email, current email will be invalid.
2. 1 email address can use for register 5 devices for control same AC.
Toshiba Home AC Control application support
Book_1129850207_EN - UA.indb 10Book_1129850207_EN - UA.indb 10 18/3/2564 BE 10:4718/3/2564 BE 10:47