Toshiba B-EP800-CHG6-QM-R User manual

Toshiba 6-Slot Battery Charger
B-EP800-CHG6-QM-R
Owner's Manual

1
This product is designed for commercial usage and is not consumer product.
Following information is only for Turkey:
AEEE Yönetmeliğine Uygundur
CE compliance:
This product is labelled with the CE mark in accordance with the provisions of the applicable European Directives for this product
and the electric accessories.
CE marking is the responsibility of Toshiba Tec Germany Imaging Systems GmbH,
Carl-Schurz-Str. 7, 41460 Neuss, Germany, phone [phone].
For a copy of the related CE Declaration of Conformity, please contact your dealer, Toshiba Tec Germany Imaging Systems
GmbH or Toshiba Tec Corporation.
UKCA compliance:
This product is labelled with the UKCA mark in accordance with the provisions of the applicable UK legislations for this product
and the electric accessories.
UKCA marking is the responsibility of Toshiba Tec U.K. Imaging Systems Ltd,
Abbey Cloisters, Abbey Green, Chertsey, Surrey, KT16 8RB, phone [phone].
For a copy of the related UKCA Declaration of Conformity, please contact your dealer, Toshiba Tec U.K. Imaging Systems Ltd or
Toshiba Tec Corporation.
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
(for CANADA only)
FCC Notice:
1. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
2. Changes or modification not expressly approved by manufacturer for compliance could void the user’s authority to operate the
equipment.
This product is marked according to the requirement on Waste electrical and electronic equipment - WEEE.
The use of the symbol indicates that product may not be disposed as unsorted municipal waste and has to be
collected separately. By ensuring this product is disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could otherwise be caused by inappropriate
waste handling of this product.
For more detailed information about the take-back and recycling of this product please contact your supplier
where you purchased the product.
Following information is only for India:
The use of the symbol indicates that this product may not be treated as household waste. By ensuring this
product is disposed of correctly, you will help prevent potential negative consequences for the environment
and human health, which could otherwise be caused by inappropriate waste handling of this product.
For more detailed information about the take-back and recycling of this product, please contact your supplie
r
where you purchased the product.
This product including components, consumables, parts and spares complies with the “India E-Waste Rules”
and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated
diphenyl ethers in concentrations exceeding 0.1% by weight and 0.01% by weight for cadmium, except fo
r
the exemption set in the Rule.
CALIFORNIA PROPOSITION 65 WARNING
WARNING:
This product can expose you to chemicals including DINP, which is/are known to the State of California to cause cancer, and
chemicals including Phthalate[s], which is/are known to the State of California to cause birth defects or other reproductive harm.
For more information go to:
www.P65Warnings.ca.gov

2
Following information is only for Vietnam:
Declaration of conformity
Toshiba Tec Group Products sold in Vietnam market complies with Circular 16/VBHN-BCT dated April 25, 2014 of the
Ministry of Industry & Trade stipulating temporarily the permissible content limitation of some toxic chemicals in the
electronic, electrical products.
NOTE:
• For indoor use only.
• The unit may become warm whilst in use, this is perfectly normal.
If any difficulty should arise, unplug the unit and contact your authorized Toshiba Tec representative.
Precautions
The following precautions will help to ensure that this machine will continue to function correctly.
• Try to avoid locations that have the following adverse conditions:
* Temperatures out of the specification * Direct sunlight * High humidity
* Shared power source * Excessive vibration * Dust/Gas
• The cover should be cleaned by wiping with a dry cloth or a cloth slightly dampened with a mild detergent solution. NEVER
USE THINNER OR ANY OTHER VOLATILE SOLVENT on the plastic covers.
• Try to avoid using this equipment on the same power supply as high voltage equipment or equipment likely to cause mains
interference.
• Unplug the machine whenever you are working inside it or cleaning it.
• Keep your work environment static free.
• Do not place heavy objects on top of the machine, as these items may become unbalanced and fall causing injury.
• Do not lean against the machine. It may fall on you and could cause injury.
• Unplug the machine when it is not used for a long period of time.
• Place the machine on a stable and level surface.
•Be sure that nothing metallic comes into contact with the metal parts of the unit or connecting plate. If it does, a short may
occur and the unit may be damaged.
• Always keep the metal contacts clean.
• Do not apply mechanical shock or drop the unit.
• Do not expose the unit to rain or moisture, as this may cause fire or electric shock.
• Do not use a spray cleaner containing flammable gas for cleaning this product, as this may cause a fire.
• Do not use voltages other than the AC voltage specified on the rating plate, as this may cause fire or electric shock.
• Do not plug in or unplug the power cord with wet hands as this may cause electric shock.
• Do not place metal objects or water-filled containers such as flower vases, flower pots or mugs, etc. on top of the machine. If
metal objects or spilled liquid enter the machine, this may cause fire or electric shock. (4)
• Do not scratch, damage or modify the power cords. Also, do not place heavy objects on, pull on, or excessively bend the
power cords, as this may cause fire or electrical shock.
• Do not remove covers, repair or modify the machine by yourself. Contact your authorised Toshiba Tec Corporation
representative for assistance. You may be injured by high voltage, very hot parts or sharp edges inside the machine.
• If the machine is dropped or their cabinet damaged, first turn off the power switch and disconnect the power cord plug from the
outlet, and then contact your authorised Toshiba Tec Corporation representative for assistance. Continued use of the machine
in that condition may cause fire or electric shock.
• Continued use of the machine in an abnormal condition such as when the machine is producing smoke or strange smells may
cause fire or electric shock. In these cases, immediately turn off the power switches and disconnect the power cord plug from
the outlet. Then, contact your authorised Toshiba Tec Corporation representative for assistance.
• If foreign objects (metal fragments, water, liquids) enter the machine, turn off the power switch and disconnect the power cord
plug from the outlet, and then contact your authorised Toshiba Tec Corporation representative for assistance. Continued use
of the machine in that condition may cause fire or electric shock.
• When unplugging the power cords, be sure to hold and pull on the plug. Pulling on the cord may cut or expose the internal
wires and cause fire or electric shock.
• Ensure that the equipment is properly grounded. Extension cables should also be grounded. Fire or electric shock could occur
on improperly grounded equipment.
CAUTION
This indicates that there is the risk of personal injury or damage to objects if the machines are improperly handled
contrary to this indication.
WARNING
This indicates that there is the risk of death or serious injury if the machines are handled improperly or contrary to this
indication.

3
When purchasing the power cord:
Since the power cord set is not enclosed in this unit, please purchase an approved one that meets the
following standard from your authorized Toshiba Tec representative.
Country Agency
Certification
mark Country Agency Certification mark Country Agency Certification mark
Australia SAA Germany VDE
Sweden SEMKKO
Austria OVE
Ireland NSAI Switzerland SEV
Belgium CEBEC
Italy IMQ
UK ASTA
Canada CSA Japan METI UK BSI
Denmark DEMKO
Netherlands KEMA U.S.A. UL
Finland FEI
Norway NEMKO Europe HAR
France UTE Spain AEE
China CCC
Power Cord Instruction
1. For use with 100 – 125 Vac mains power supply, please select a power cord rated Min. 125V, 10A.
2. For use with 200 – 240 Vac mains power supply, please select a power cord rated Min. 250V.
3. Please select a power cord with the length of 2m or less.
4. The power cord plug connected to the AC adapter must be able to be inserted to an ICE-320-C14 inlet.
Refer to the following figure for the shape.
Country/Region North America Europe United
Kin
g
dom Australia China
Power Cord
Rated (Min.)
Type
Conductor size
(Min.)
125V, 10A
SVT
No. 3/18AWG
250V
H05VV-F
3 x 0.75 mm2
250V
H05VV-F
3 x 0.75 mm2
250V
AS3191 approved,
Light or Ordinary Duty type
3 x 0.75 mm2
250V
GB5023
3 x 0.75 mm2
Plug Configuration
(locally approved
type)
Rated (Min.)
125V, 10A 250V, 10A 250V, *1 250V, *1 250V, *1
*1: At least, 125% of the rated current of the product.

4
To Charge the Battery Pack
Please use the following procedure to charge a battery pack. This battery charger can charge six
battery packs at the same time with B-EP802-BT-QM-R, B-EP804-BT-QM-R, B-FP803-BT-QM-R
and the B-FP803-BTH-QM-R mixed.
1. Fit the partition into the slot. The orientation of the partition differs depending on the battery
pack size to be charged.
NOTE:
Fit the partition in the correct position and orientation and make sure the tabs are fit into the
holes.
Be careful not to lose the partition.
Care must be taken not to mistake the orientation, as the partition cannot be removed once it
is fitted.
2. Connect the AC adapter to the battery
charger.
3. Connect the power cord to the AC adapter.
4. Connect the power cord to an AC outlet.
When charging
B-EP802-BT-QM-R,
B-FP803-BT-QM-R or
B-FP803-BTH-QM-R
battery pack
When charging
B-EP804-BT-QM-R
battery pack
Tab
Tab
Battery Charger
Power Cord
AC Adapter
AC Outlet
1. The B-EP800-CHG6-QM-R battery charger is designed and manufactured for use with specified lithium-ion
battery packs. The battery used in this device may present a risk of fire or chemical burn if mistreated. Do not
disassemble, heat above +50degC, or incinerate. Replace battery with specified type only. There is a risk of fire or
explosion if the battery is replaced by an incorrect type.
Available
Batter
y
Pack B-EP802-BT-QM-R B-EP804-BT-QM-R B-FP803-BT-QM-R B-FP803-BTH-QM-R
2. Dispose of used battery promptly. Keep away from children. Do not disassemble and do not dispose of in fire.
3
. Use onl
y
the supplied AC adapter
(
Model: F
S
P150-ABA
N
3
)
for powerin
g
this batter
y
char
g
er.
WARNIN
G

5
5. Insert the battery pack into the slot in the orientation
shown below.
The CHARGE lamp will light up and charging will
begin.
NOTE:
Insert an appropriate size of the battery pack
according to the partition’s orientation. Failure to
do this may damage the battery pack or affect
charging operation.
Place the battery pack firmly.
Charge the battery pack on a flat, steady surface.
The CHARGE lamp indicates a charging status.
CHARGE lamp State
OFF Unconnected.
Red Char
g
ed.
Green Completed.
Blinking red Abnormal state
6. After charging is completed, remove the battery pack from the battery charger.
7. Disconnect the power cord from the AC outlet.
Charging time
To charge an empty battery pack:
Battery pack Charging time
B-EP802-BT-QM-R
B-EP804-BT-QM-R
B-FP803-BT-QM-R
B-FP803-BTH-QM-R
about 3 hours
(Until the min. of 85% of the nominal capacity is charged.)
• Charging time may differ depending on the condition of the battery pack or the operating
temperature.
• After the CHARGE lamp turns from red to green, the battery charger may continue to charge
the battery pack for up to one more hour until the full charge level (95% or more).
NOTE:
1. Battery packs should be charged on condition that both ambient temperature and battery
temperature fall within a range of 0 °C to 40°C.
2. The battery charger will get warmer during charging (room temperature + about 30°C). This is
not abnormal.
3. If the over discharge protector has been operated on a battery pack, the CHARGE lamp may
not light for a while. Leave the battery charger and the battery pack alone for a few minutes.
Stop using the battery pack if the CHARGE lamp does not light at all as the battery pack may be
faulty.
4. The battery pack can be removed from the battery charger while charging is in progress.
However, the battery lasting time depends on the charging time.
5. After the charging is completed, do not leave the battery pack in the charger too long. The
battery pack gradually discharges.
6. Periodically clean the charger terminals with a soft dry cloth.
NOTE:
The green light does not go off until the battery
p
ack is removed from the slot.
Battery Pack
CHARGE Lamp Partition

6
TROUBLESHOOTING
If you have any problems while using this product, please check the following point first.
If a problem cannot be solved by taking actions described below, unplug the battery charger and
contact the dealer or an authorized Toshiba Tec service representative for assistance.
Symptom Cause and resolution
A battery pack is loaded in the
battery charger, but the
CHARGE lamp does not light
up in red.
The power cord is not connected properly.
Firmly connect the power cord to the AC adapter and the AC
outlet.
The terminals of the battery charger or the battery electrodes
are stained.
Wipe clean those portions with a soft dry cloth.
You are attempting to charge a battery pack with the over
discharge protection activated (The CHARGE lamp may not
light up immediately after loading a battery.)
Leave the battery charger and the battery pack alone for a
few minutes. If the CHARGE lamp does not light after all,
stop using the battery pack, as the battery pack may be
faulty.
The partition is not fitted.
Fit the partition in the correct orientation.
The CHARGE lamp blinks in
red.
A battery pack failure is detected.
It could be the end of battery life. Replace the battery pack
with a new one.
Charging time overruns the
approximate specified time.
Charging time varies depending on the condition of the battery
pack, ambient temperature, etc.
If the battery charger continues charging even after the
specified time has passed, stop charging and replace the
battery pack with a new one.
Battery pack does not last long
time though the battery is fully
charged.
It could be the end of battery life.
Replace the battery pack with a new one.
The battery pack cannot be
inserted into the slot.
The partition is not set completely.
Fit the partition completely.

7
Specifications
Item Batter
y
char
g
er AC Adapter
(
Accessor
y)
Model B-EP800-CHG6-QM-R
(
EP800-CHG6
)
FSP150-ABAN3
Power requirements DC +19V, 7.89A (Supplied by the AC
adapter
)
100 to 240V AC, 50/60 Hz
Output voltage --- DC+19V, 7.89A
Application Toshiba Tec battery pack
B-EP802-BT-QM-R (7.4V 2600mAh)
B-EP804-BT-QM-R (14.8V 2600mAh)
B-FP803-BT-QM-R which is equivalent
to 18650/2S1P(7.4V 2500mAh)
B-FP803-BTH-QM-R which is equivalent
to 2S1P/18650(7.2V 2500mAh) or
2S1P21/18650
(
7.2V 2400mAh
)
Toshiba Battery Charger
B-EP800-CHG6-QM-R
(EP800-CHG6)
Number of slots 6 slots (Every slot can charge a battery
pack independently.)
The battery pack model is automatically
sensed.
---
Operating temperature 0°C to 40°C (32°F to 104°F)
Operating humidity 20 to 80% (no condensation)
Storage temperature -20°C to 60°C (-4°F to 140°F)
Storage humidity 10 to 85% (no condensation)
Dimensions 148 x 77 x 213 mm (w/h/d)
(5.83” x 3.03” x 8.39”) excluding the
pro
j
ectin
g
parts
72 x 40 x 171 mm (w/h/d)
(2.83” x 1.57” x 6.73”)
excludin
g
the pro
j
ectin
g
parts
Weight Approx. 900 g (31.7 oz) (Excluding the
accessories
)
Approx. 800 g (28.2 oz)
A
ccessories
A
C adapter x 1, Partition x 6, Owne
r
’s Manual x 1
NOTE: Design and specifications are subject to change without notice.
EN PRINTED IN INDONESIA
BU21000800-EN_N3
R211020Y8500-TTEC
© 2006-2022 Toshiba Tec Corporation All Rights Reserved
1-11-1, Osaki, Shinagawa-ku, Tokyo 141-8562, JAPAN