Toshiba RemotEye 4 Instruction Manual

Instructions for G9000 Series UPS RemotEye –90000-004 Page 1 of 8
Part No. 90000-004
Date: February 2020
Procedure for Installing the RemotEye®4
on G9000 Series UPS (Pre-Installed Brackets)
This kit contains the parts to neatly and securely attach the RemotEye 4 network monitoring card
(Part # T90RMTI4-NB) to the inside door of all G9000 UPSs. This document covers attaching the
device with the hardware kit only; for wiring and programming instructions, refer to the RemotEye 4
User Manual (Document #90988).
Important Note: this Guide is for RemotEye 4 installations on G9000 units shipped after February
14th, 2017. Please use Part # T90RMTI4 and reference the previous revision of this manual (#90000-
002) for any units shipped before this date.
1.0 Contents Table 1 RemotEye 4 Installation Kit Contents
Kit Contents
No.
Item
Qty.
1
RemotEye 4 Card w/ Box
1
2
93805 –RemotEye 4 Comm Cable
1
3
65816 –RemotEye 4 PCB Mounting Box
1
4
Accessory Pack (Details Below)
1
4.1
Standoff, M3 x 15mm
2
4.2
Screw, M3 x 12mm
2
4.3
Screw, 6/32 x 3/8in.
4
4.4
Zip Tie
5

Instructions for G9000 Series UPS RemotEye –90000-004 Page 2 of 8
Figure 1: RemotEye 4 PCB Mounting Box #65816
Figure 2: RemotEye 4 Comm Cable #93805
Figure 3: Accessory Pack
Mounting Hardware:
2 –Standoffs, M3 x 15mm
2 –Screw, M3 x 12mm
4 –Screw, 6/32 x 3/8”
5 –Zip Tie

Instructions for G9000 Series UPS RemotEye –90000-004 Page 3 of 8
2.0 LOCATE REMOTEYE MOUNTING PLATE & BRACKET
This step gives instructions for locating the RemotEye Mounting Plate in any of the G9000
Series UPS.
2.1 Ensure that power is being provided to the G9000 UPS.
2.2 Open the G9000’s door, and remove the dead front cover (if any) covering the display PCBs
on the inside of the door.
2.3 Reference Figure 4 through Figure 9 to determine the specific location of the RemotEye 4
mounting location as well as the mounting holes for the ribbon cable bracket (shown within
the red ellipse). The mounting plate and bracket are pre-installed in this area. Note: as shown
in Figure 9, the 1000kVA mounting location is in the unit itself, not the reverse side of the
door.
Figure 4: 100/160kVA RemotEye 4 Location
Figure 5: 225kVA RemotEye 4 Location

Instructions for G9000 Series UPS RemotEye –90000-004 Page 4 of 8
Figure 6: 300kVA RemotEye 4 Location
Figure 7: 500kVA RemotEye 4 Location

Instructions for G9000 Series UPS RemotEye –90000-004 Page 5 of 8
Figure 8: 750kVA RemotEye 4 Location
Figure 9: 1000kVA RemotEye 4 Location

Instructions for G9000 Series UPS RemotEye –90000-004 Page 6 of 8
3.0 INSTALL REMOTEYE 4
This step provides instructions for mounting and connecting the RemotEye 4 in the G9000
Series UPS.
NOTE: Numbered components in Figures 11-13 correspond to the numbered entries of the Kit
Contents Table on Page 1.
3.1 Orient the PCB Mounting Box, Figure 11-(3) so the back connector is on the same side
as the RemotEye 4 Mounting Bracket angle and press the mounting box into the
mounting bracket until the retaining tabs, Figure 11-(3T), engage. Secure it with two of
the panhead Philips 6/32 x 3/8” screws, Figure 11-(4.3a).
3.2 Connect the Edge Card Connector, Figure 11-(2a), of the RemotEye
4 Comm Cable, Figure 11-(2b) to the RemotEye 4 PCB.
3.3 Remove the Adapter Plug, Figure 10, from the G9000 PSAU-60
Communications board connector CN-1.
3.4 Insert the RemotEye 4 PCB into the PCB Mounting Box and secure
it with two of the panhead Philips 6/32 x 3/8” screws, Figure 11-
(4.3b).
Figure 11: Install RemotEye 4 on Mounting Plate
3.5 Connect the ribbon cable’s RMTI CONN plug, Figure 12/13-(2b), to the RMTI CONN
plug of the RemotEye 4 to COMM BOARD wire assembly, Figure 12/13-(2c).
3.6 Connect the female D-SUB9, Figure 12/13-(2f), and CN2, Figure 12/13-(2g), plugs of
the RemotEye 4 Comm Cable, Figure 12/13-(2e), to the G9000 PSAU-60 Comm Board.
3
2a
4.3b
4.3b
2b
2c
3T
4.4
Adapter Plug
Figure 10: PSAU-60
CN1 Adapter Plug
4.3a

Instructions for G9000 Series UPS RemotEye –90000-004 Page 7 of 8
3.7 Secure the wiring with the provided cable ties or equivalent as shown in Figures 11, 12
& 13-(4.4)
3.8 This completes the hardware installation of the RemotEye 4. Complete the setup of the
RemotEye 4 per the RemotEye 4 User’s Manual, P/N 90988.
Figure 12: Install RemotEye 4 Cabling
2f
PSAU-60
2g
2e
4.4
2a
2b
2c

Instructions for G9000 Series UPS RemotEye –90000-004 Page 8 of 8
Figure 13: Install RemotEye 4 Cabling (500kVA)
PSAU-60
2f
2g
2e
4.4
2a
2b
2c
2d