Toshiba e-STUDIO350 User manual

MULTIFUNCTIONAL DIGITAL SYSTEMS
e-STUDIO350/450
File No. SME03002800
R03092140700-TTEC
Ver00 2003-11

© 2003 TOSHIBA TEC CORPORATION
All rights reserved

GENERAL PRECAUTIONS REGARDING THE INSTALLATION
AND SERVICE FOR e-STUDIO350/450
1. Transportation / Installation
• When transporting/installing the equipment, employ two persons and be sure to use the posi
tions as indicated below.
The equipment is quite heavy and weighs approximately 83kg (182.98 lb.) therefore pay full
attention when handling it.
• Be sure not to hold the movable parts or units (e.g. the control panel, ADU or RADF) when
transporting the equipment.
• Be sure to use a dedicated outlet with AC 110V/13.2A, 115V or 127V / 12A, 220-240V or 240V
/ 8A for its power source.
• The equipment must be grounded for safety.
Never ground it to a gas pipe or a water pipe.
• Select a suitable place for installation.
Avoid excessive heat, high humidity, dust, vibration and direct sunlight.
• Also provide proper ventilation as the equipment emits a slight amount of ozone.
• To insure adequate working space for the copying operation, keep a minimum clearance of
80 cm (32”) on the left, 80 cm (32”) on the right and 10 cm (4”) in the rear.
• The socket-outlet shall be installed near the equipment and shall be easily accessible.
2. Service of Machines
• Basically, be sure to turn the main switch off and unplug the power cord during service.
• Be sure not to touch high-temperature sections such as the exposure lamp, the fuser unit, the
damp heater and their periphery.
• Be sure not to touch high-voltage sections such as the chargers, developer, IH control circuit,
high-voltage transformer, exposure lamp control inverter, inverter for the LCD backlight and
power supply unit. Especially, the board of these components should not be touched since the
electric charge may remain in the capacitors, etc. on them even after the power is turned OFF.
• Be sure not to touch rotating/operating sections such as gears, belts, pulleys, fan, etc.
• Be careful when removing the covers since there might be the parts with very sharp edges
underneath.
• When servicing the machines with the power turned ON, be sure not to touch live sections
and rotating/operating sections. Avoid exposure to laser radiation.
The installation and service should be done by a qualified service technician.

Caution : Dispose of used batteries and RAM-ICs including lithium batteries according
to this manual.
Attention : Se débarrasser de batteries et RAM-ICs usés y compris les batteries en lithium
selon ce manuel.
Vorsicht : Entsorgung des gebrauchten Batterien und RAM-ICs (inklusive
der Lithium-Batterie) nach diesem Handbuch.
• Use suitable measuring instruments and tools.
• Avoid exposure to laser radiation during servicing.
- Avoid direct exposure to the beam.
- Do not insert tools, parts, etc. that are reflective into the path of the laser beam.
- Remove all watches, rings, bracelets, etc. that are reflective.
• Unplug the power cable and clean the area around the prongs of the plug once a year or more.
A fire may occur when dust lies on this area.
3. Main Service Parts for Safety
• The breaker, door switch, fuse, thermostat, thermofuse, thermistor, etc. are particularly
important for safety. Be sure to handle/install them properly. If these parts are shorted circuit
and/or made their functions out, they may burn down, for instance, and may result in fatal
accidents. Do not allow a short circuit to occur. Do not use the parts not recommended
by Toshiba TEC Corporation.
4. Cautionary Labels
• During servicing, be sure to check the rating plate and the cautionary labels such as “Unplug
the power cord during service”, “Hot area”, “Laser warning label” etc. to see if there is any dirt
on their surface and whether they are properly stuck to the equipment.
5. Disposition of Consumable Parts, Packing Materials, Used batteries and RAM-ICs
• Regarding the recovery and disposal of the equipment, supplies, consumable parts, packing
materials, used batteries and RAM-ICs including lithium batteries, follow the relevant local
regulations or rules.
6. When parts are disassembled, reassembly is basically the reverse of disassembly unless
otherwise noted in this manual or other related documents. Be careful not to reassemble
small parts such as screws, washers, pins, E-rings, star washers in the wrong places.
7. Basically, the machine should not be operated with any parts removed or disassembled.
8. Precautions Against Static Electricity
• The PC board must be stored in an anti-electrostatic bag and handled carefully using a wrist-
band, because the ICs on it may become damaged due to static electricity.
Caution: Before using the wristband, pull out the power cord plug of the equipment and
make sure that there are no uninsulated charged objects in the vicinity.

November 2003 © TOSHIBA TEC i e-STUDIO3511/4511 CONTENTS
CONTENTS
1. SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES..................................... 1-1
1.1 Specifications ..................................................................................................................... 1-1
1.2 Accessories ........................................................................................................................ 1-5
1.3 Options ............................................................................................................................... 1-6
1.4 Supplies .............................................................................................................................. 1-6
1.5 System List ......................................................................................................................... 1-7
2. OUTLINE OF THE MACHINE ........................................................................................ 2-1
2.1 Sectional View .................................................................................................................... 2-1
2.2 Electric Parts Layout ........................................................................................................... 2-5
2.3 Symbols and Functions of Various Components .............................................................. 2-14
2.4 General Description .......................................................................................................... 2-21
2.5 Installation and Replacement of Covers and PC boards ................................................... 2-25
2.6 Options ............................................................................................................................. 2-35
3. COPY PROCESS ............................................................................................................ 3-1
3.1 General Description of Copying Process ............................................................................ 3-1
3.2 Details of Copying Process ................................................................................................. 3-2
3.3 Comparison with DP4500/3500 ........................................................................................ 3-10
4. GENERAL OPERATION ................................................................................................ 4-1
4.1 Overview of Operation ........................................................................................................ 4-1
4.2 Description of Operation ..................................................................................................... 4-1
4.2.1 Warming-up ............................................................................................................. 4-1
4.2.2 Ready state (ready for copying) .............................................................................. 4-2
4.2.3 Drawer feed copying (Upper drawer paper feeding) ................................................ 4-2
4.2.4 Bypass feed copying................................................................................................ 4-5
4.2.5 Interruption copying ................................................................................................. 4-5
4.3 Detection of Abnormality ..................................................................................................... 4-6
4.3.1 Types of abnormality ................................................................................................ 4-6
4.3.2 Description of abnormality ........................................................................................ 4-7
4.4 Flow Chart ........................................................................................................................ 4-12
4.4.1 Immediately after the power is turned ON ............................................................... 4-12
4.4.2 Automatic paper feed copying ................................................................................ 4-14
5. CONTROL PANEL ......................................................................................................... 5-1
5.1 Control Panel and Display Panel ........................................................................................ 5-1
5.2 Items Shown on the Display Panel ..................................................................................... 5-2
5.2.1 Display..................................................................................................................... 5-3
5.3 Relation between the Equipment State and Operator’s Operation ...................................... 5-8

e-STUDIO3511/4511 CONTENTS ii November 2003 © TOSHIBA TEC
5.4 Description of Operation ..................................................................................................... 5-9
5.4.1 Dot matrix LCD circuit .............................................................................................. 5-9
5.4.2 LED display circuit ................................................................................................. 5-11
5.5 Disassembly and Replacement ........................................................................................ 5-12
6. SCANNER ..................................................................................................................... 6-1
6.1 Function ............................................................................................................................. 6-1
6.2 Construction ....................................................................................................................... 6-2
6.3 Description of Operation ..................................................................................................... 6-4
6.3.1 Scan motor .............................................................................................................. 6-4
6.3.2 Scanning drive circuit .............................................................................................. 6-5
6.3.3 Initialization at power-ON ........................................................................................ 6-7
6.4 Control of Exposure Lamp .................................................................................................. 6-8
6.4.1 General description ................................................................................................. 6-8
6.4.2 Exposure lamp ........................................................................................................ 6-9
6.4.3 Control circuit for the exposure lamp ..................................................................... 6-10
6.5 General Description of CCD Control ................................................................................. 6-11
6.5.1 Opto-electronic conversion.................................................................................... 6-11
6.5.2 Shading correction ................................................................................................ 6-11
6.6 Automatic Original Size Detection Circuit ......................................................................... 6-12
6.6.1 Principle of original size detection ......................................................................... 6-12
6.6.2 Process of detection of original size ...................................................................... 6-12
6.7 Disassembly and Replacement ........................................................................................ 6-16
7. IMAGE PROCESSING ................................................................................................... 7-1
7.1 General Description ............................................................................................................ 7-1
7.2 Configuration ...................................................................................................................... 7-3
7.3 SLG Board (PWA-F-SLG-360) ........................................................................................... 7-4
7.3.1 Features .................................................................................................................. 7-4
7.3.2 Functions of image processing circuit ...................................................................... 7-5
7.4 LGC Board (PWA-F-LGC-360) ........................................................................................... 7-9
7.4.1 Features .................................................................................................................. 7-9
7.4.2 Functions of image processing circuit ....................................................................... 7-9
7.5 Laser Driving PC Board .................................................................................................... 7-10
8. LASER OPTICAL UNIT .................................................................................................. 8-1
8.1 General Description ............................................................................................................ 8-1
8.2 Structure ............................................................................................................................. 8-3
8.3 Laser Diode ........................................................................................................................ 8-7
8.4 Laser Optical Unit Cooling Fan ........................................................................................... 8-8
8.5 Polygonal Motor .................................................................................................................. 8-8
8.6 Disassembly and Replacement .......................................................................................... 8-9

November 2003 © TOSHIBA TEC iii e-STUDIO3511/4511 CONTENTS
9. PAPER FEEDING SYSTEM ........................................................................................... 9-1
9.1 Functions ............................................................................................................................ 9-1
9.2 Operation ............................................................................................................................ 9-5
9.2.1 Operation of bypass pickup roller ............................................................................ 9-5
9.2.2 Operation of drawer pickup roller ............................................................................ 9-5
9.2.3 Separation of paper ................................................................................................... 9-6
9.2.4 General operation ................................................................................................... 9-7
9.3 Drive Circuit of Tray-up Motor............................................................................................. 9-9
9.4 Disassembly and Replacement ........................................................................................ 9-10
10. DRIVE SYSTEM .......................................................................................................... 10-1
10.1 General Description ........................................................................................................ 10-1
10.2 Functions ........................................................................................................................ 10-1
10.3 Main Motor...................................................................................................................... 10-2
10.3.1 Main motor drive ................................................................................................... 10-2
10.3.2 Control signals ...................................................................................................... 10-3
10.4 Disassembly and Replacement ....................................................................................... 10-4
11. DRUM RELATED SECTION....................................................................................... 11-1
11.1 Configuration .................................................................................................................... 11-1
11.2 Functions ......................................................................................................................... 11-2
11.3 Output Control Circuits of High-Voltage Transformer ....................................................... 11-5
11.3.1 Overview .............................................................................................................. 11-5
11.3.2 Description of operations ...................................................................................... 11-5
11.4 Drum Temperature Detection Circuit .............................................................................. 11-7
11.5 Temperature/Humidity Sensor ........................................................................................ 11-8
11.5.1 General description ............................................................................................... 11-8
11.5.2 Construction .......................................................................................................... 11-8
11.6 Disassembly and Replacement ...................................................................................... 11-9
12. DEVELOPMENT SYSTEM ......................................................................................... 12-1
12.1 Configuration ................................................................................................................... 12-1
12.2 Functions ......................................................................................................................... 12-2
12.3 Drive Circuit of Toner Motor ............................................................................................. 12-3
12.4 Auto-Toner Circuit ............................................................................................................ 12-4
12.4.1 General description ............................................................................................... 12-4
12.4.2 Function of auto-toner sensor ............................................................................... 12-5
12.4.3 Adjustment using the temperature / humidity sensor ............................................ 12-7
12.4.4 Adjustment using the drum thermistor .................................................................. 12-7
12.5 Disassembly and Replacement ....................................................................................... 128
13. FUSER UNIT / PAPER EXIT SECTION ...................................................................... 13-1
13.1 General Description .......................................................................................................... 13-1
13.2 Operation ......................................................................................................................... 13-1
13.3 Functions .......................................................................................................................... 13-2

e-STUDIO3511/4511 CONTENTS iv November 2003 © TOSHIBA TEC
13.4 Heater Control Circuit ..................................................................................................... 13-4
13.4.1 Configuration ........................................................................................................ 13-4
13.4.2 Heating principle of IH Heater ............................................................................... 13-5
13.4.3 IH control circuit interface .................................................................................... 13-6
13.4.4 Relation between system configuration and IH output .......................................... 13-7
13.4.5 Temperature detection section ............................................................................. 13-8
13.4.6 Abnormality in the IH control circuit .................................................................... 13-13
13.5 Control Circuit of Exit Motor .......................................................................................... 13-15
13.6 Exit Motor Drive ............................................................................................................ 13-15
13.7 Disassembly and Replacement .................................................................................... 13-16
14. AUTOMATIC DUPLEXING UNIT (ADU) .................................................................... 14-1
14.1 General Description ........................................................................................................ 14-1
14.2 Description of Operations ............................................................................................... 14-2
14.3 Drive of ADU................................................................................................................... 14-8
14.4 Flow Chart ...................................................................................................................... 14-9
14.5 Disassembly and Replacement .................................................................................... 14-11
15. POWER SUPPLY UNIT .............................................................................................. 15-1
15.1 Construction ................................................................................................................... 15-1
15.2 Operation of DC Output Circuits ..................................................................................... 15-1
15.3 Output Channel .............................................................................................................. 15-2
15.4 Fuse ............................................................................................................................... 15-4
15.5 Configuration of Power Supply Unit ................................................................................ 15-5
15.6 Sequence of Power Supply............................................................................................. 15-6
15.7 AC Wire Harness ............................................................................................................ 15-7
16. PC BOARDS............................................................................................................... 16-1

November 2003 © TOSHIBA TEC 1 - 1 e-STUDIO350/450 SPECIFICATIONS
1
1. SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES
1.1 Specifications
Values in [ ] are for e-STUDIO450 in case that the specification is different between e-STUDIO350 and
e-STUDIO450.
• Copy process Indirect electrophotographic process (dry)
• Type Desktop type (console type:when paper feed pedestal (PFP) and large capac-
ity feeder (LCF) are installed)
• Original table Fixed type (the left rear corner used as guide to place originals)
• Accepted originals Sheet, book and 3-dimensional object. The reversing automatic document
feeder (RADF) only accepts paper which are not pasted or stapled. (Single-
sided originals: 50 to 127 g/m2/13 to 34lb. Bond, Double-sided originals: 50
to105 g/m2/13 to 28 lb. Bond) Carbon paper are not acceptable either.
Maximum size : A3/LD
• Copy speed (Copies/min.)
*“–” means “Not acceptable”.
*The copy speed in the above table are available when originals are manually placed for single side,
multiple copying.
*When the RADF is used, the copy speed of 35[45] sheets per minute is only available under the
following conditions:
• Original/Mode: Single side original/A4/LT size. APS/automatic density are not selected.
• Number of sheets: 35[45] or more.
• Paper feeding: LCF
• Reproduction ratio: 100%
e-STUDIO450
e-STUDIO350
Paper supply
Paper size
A4, LT, B5
A4-R, B5-R,
A5-R, LT-R, ST-R
B4, LG
A3, LD
Drawer
35
25
21
18
Size specified
35
25
21
18
Size not specified
18
18
18
18
PFP
35
25
21
18
Bypass feed LCF
35
–
–
–
Paper supply
Paper size
A4, LT, B5
A4-R, B5-R,
A5-R, LT-R, ST-R
B4, LG
A3, LD
Drawer
45
28
24
21
Size specified
40
28
24
21
Size not specified
21
21
21
21
PFP
45
28
24
21
Bypass feed LCF
45
–
–
–

e-STUDIO350/450 SPECIFICATIONS 1 - 2 November 2003 © TOSHIBA TEC
1* System copy speed
• First copy time ................... e-STUDIO350: Approx. 3.9sec. or less
e-STUDIO450: Approx. 3.9sec. or less
(A4/LT, upper drawer, 100%, original placed manually)
• Warming-up time ............... Approx. 20 seconds (temperature: 20°C)
• Multiple copying ................. Up to 999 copies; Key in set numbers
• Reproduction ratio ............. Actual ratio: 100±0.5%
Zooming: 25 to 400% in increments of 1%
(25 to 200% when using RADF)
• Resolution/Gradation ......... Scanning: 600 dpi x 600 dpi
........ Printing: Equivalent to 2400 dpi x 600 dpi
........ Gradation: 256 steps
*The system copy speed, including
scanning time, is available when 10
sheets of A4/LT size original are
set on RADF and one of the copy
modes in the left table is selected.
The period of time from pressing
[START] to the paper exit com-
pletely out of the equipment based
on the actually measured value.
*Upper drawer is selected and
copying is at the non-sort mode.
*Automatic copy density, APS/AMS
are turned off.
*Finisher is not installed.
• Copy paper
Drawer ADU PFP LCF Bypass copy Remarks
Size A3 to A5-R A3 to A5-R,LD to ST-R
LD to ST-R A4, LT (Non-standard or user-
specified sizes can be set.)
Weight 64 to 209 g/m
2
,17 to 55 lb.
64 to 105 g/m2(Continuous feeding)
17 to 28 lb. 50 to 209 g/m
2
, 13 to 55 lb.
(Single pape r feeding)
Special Tracing paper, labels,
paper – OHP film (thickness: 80 µm
or thicker)
These special papers
recommended
by Toshiba Tec
Single-sided originals
↓
Single-sided copies
Single-sided originals
↓
Double-sided copies
Double-sided originals
↓
Double-sided copies
Double-sided originals
↓
Single-sided copies
e-STUDIO350
20.85
57.95
91.20
27.42
62.18
97.55
55.47
126.21
196.93
48.22
117.44
184.96
Copy mode
1 set
3 sets
5 sets
1 set
3 sets
5 sets
1 set
3 sets
5 sets
1 set
3 sets
5 sets
e-STUDIO450
17.49
46.68
73.50
25.71
57.41
89.03
54.68
118.07
181.36
48.20
102.18
155.06
Sec.

November 2003 © TOSHIBA TEC 1 - 3 e-STUDIO350/450 SPECIFICATIONS
1
• Eliminated portion ............. Leading edges : 3.0±2.0 mm, Side/trailing edges : 2.0±2.0 mm (copy)
Leading / trailing edges : 5.0±2.0 mm, Side edges : 5.0±2.0 mm (print)
• Paper feeding .................... Automatic feeding : Standard drawers–2 drawers (stack height 60.5
mm, equivalent to 550 sheets; 64 to 80 g/m2 (17 to
22 lb.))
PFP–Option (One drawer or two : stack height
60.5 mm, equivalent to 550 sheets; 64 to 80 g/m2
(17 to 22 lb.))
LCF–Option (Stack height 137.5 mm x 2: equivalent
to 2500 sheets; 64 to 80 g/m2 (17 to 22 lb.))
Bypass feeding: (Stack height 11 mm : equivalent to 100 sheets; 64 to
80 g/m2(17 to 22 lb.))
• Capacity of originals in the reversing automatic document feeder (Option)
................. A3 to A5-R, LD to ST-R : 100 sheets / 80 g/m2 (Stack height 16mm or less)
• Automatic duplexing unit ... Stackless, Switchback type
• Toner supply ...................... Automatic toner density detection/supply
Toner cartridge replacing method
• Density control .................. Automatic density mode and manual density mode selectable in 11 steps
• Weight ............................... 83 kg, 183 lb
• Power requirements .......... AC 110V (±10%) / 13.2A, 115V (±10%) or 127V (±10%) / 12A
220-240V (±10%) or 240V (±10%) / 8A
• Power consumption ........... 1.5 kW or less (115V series, 200V series)
*The electric power is supplied to the RADF, Finisher, Job Separator, Offset Tray, PFP and LCF
through the equipment.
• Total counter ...................... Electronical counter

e-STUDIO350/450 SPECIFICATIONS 1 - 4 November 2003 © TOSHIBA TEC
1• Dimensions of the equipment ...... See the figure below (W660 x D718 x H739 mm)
Fig. 1-101
* When the tilt angle of the control panel is 45 degrees.

November 2003 © TOSHIBA TEC 1 - 5 e-STUDIO350/450 SPECIFICATIONS
1
1.2 Accessories
Unpacking/setup instruction 1 set
Operator’s manual 4 pcs. (except for MJD)
Operator's manual pocket 1 pc.
Power cable 1 pc.
Warranty sheet 1 pc. (for NAD)
Setup report 1 set (for NAD and MJD)
Customer satisfaction card 1 pc. (for MJD)
PM sticker 1 pc. (for MJD)
Drum (installed inside of the equipment) 1 pc.
Toner bag 1 pc.
Toner cartridge 1 pc. (except for NAD,MJD)
Developer material 1 pc. (except for NAD,MJD)
Operation panel stopper 1 pc.
Blind seal 4 pcs.
Rubber plug 4 pcs.
CD-ROM 5 pcs.
* Machine version
NAD: North America
MJD: Europe
AUD: Australia
ASD: Asia
TWD: Taiwan
SAD: Saudi Arabia
JPD: Japan
CND: China

e-STUDIO350/450 SPECIFICATIONS 1 - 6 November 2003 © TOSHIBA TEC
11.3 Options
Platen Cover KA-3511 PC/PC-C
Reversing Automatic Document Feeder (RADF) MR-3015
Drawer Module MY-1021 /-C
Paper Feed Pedestal (PFP) KD-1011 /-C
Large capacity feeder (LCF) KD-1012 A4/LT/A4-C
Finisher (Hanging type) MJ-1022 /-C
Finisher (Console type) MJ-1023 /-C
Finisher (Console saddle stitcher type) MJ-1024 /-C
Hole Punch Unit MJ-6004 N/E/F/S *1
Staple Cartridge STAPLE-1600 (for MJ-1022)
STAPLE-2000 (for MJ-1023/1024)
STAPLE-600 (for MJ-1024)
Bridge Kit KN-3520 /-C
Job Separator MJ-5004 /-C
Offset Tray MJ-5005 /-C
Key Counter MU-8, MU-10
Work Tray KK-3511
Damp Heater MF-3520 U/E
Fax Board GD-1150 NA/AU/EU/TW/C/AS
2nd Line for Fax Board GD-1160 NA/EU/TW/C
Wireless LAN Adapter GN-1010
PCI Slot GO-1030
Scrambler Board GP-1030
Printer Kit GM-1010
Printer/Scanner Kit GM-2010
Scanner upgrade Kit GM-3010
Desk MH-1700
* 1) N : North America E : Europe F : France S : Sweden
Notes:
1. The bridge unit (KN-3511) is necessary for installation of the finisher (MJ-1022, MJ-1023 or MJ-
1024).
2. The finisher (MJ-1023 or MJ-1024) is necessary for installation of the hole punch unit (MJ-
6004N/E/F/S).
3. The PCI slot (GO-1030) is necessary for installation of the scrambler board (GP-1030).

November 2003 © TOSHIBA TEC 1 - 7 e-STUDIO350/450 SPECIFICATIONS
1
1.4 Supplies
Drum OD-3500
Toner bag PS-TB3520 /E/N *2
Toner cartridge PS-ZT3520 /T/D/C/E *3
Developer D-3500
* 2) N : Asia E : Europe NONE : North America
* 3) T : Taiwan D : Asia C : China E : Europe NONE : North America

e-STUDIO350/450 SPECIFICATIONS 1 - 8 November 2003 © TOSHIBA TEC
1
Fig. 1-501
1.5 System List
Staple Cartridge
STAPLE-1600
Work Tray
KK-3511
Platen Cover
KA-3511
Reversing Automatic
Document Feeder
(RADF)
MR-3015
Key Counter
MU-8, MU-10
Bridge Kit
KN-3520
Job Separator
MJ-5004
Offset Tray
MJ-5005
Scrambler
Board
GP-1030
PCI Slot
GO-1030
FAX Board
GD-1150
NA/AU/EU/
TW/C/AS
2nd Line for
FAX Board
GD-1160
NA/EU/TW/C
Wireless LAN
Adapter
GN-1010
Damp Heater MF-3520 U/E
Printer Kit
GM-1010
Desk
MH-1700
Drawer Module
MY-1021
Large Capacity
Feeder (LCF)
KD-1012 A4/LT
Paper Feed
Pedestal (PFP)
KD-1011
Printer/
Scanner Kit
GM-2010
Scanner
Upgrade Kit
GM-3010
Staple Cartridge
STAPLE-2000
Hole Punch Unit
MJ-6004 N/E/F/S
Staple Cartridge
STAPLE-600
Finisher
(Hanging type)
MJ-1022
Finisher
(Console type)
MJ-1023
Finisher
(Console saddle
stitcher type)
MJ-1024

November 2003 © TOSHIBA TEC 2 - 1 e-STUDIO350/450 OUTLINE OF THE MACHINE
2
2. OUTLINE OF THE MACHINE
2.1 Sectional View
Fig. 2-101
12
3
4
5
678
9
10
11
12
13 14
15
16
17
18
19
20,21
22
23
23
24
25
26
27 28
29
30
31
32
3334
35
36
37
38
39
40
41
42
43 44
45
46 47
48
4950
51
52
53
54
55
56,59 57 58
60
61 6263 64
65
67
66
68
69
70 71
72
13 14
15
19
20,21

e-STUDIO350/450 OUTLINE OF THE MACHINE 2 - 2 November 2003 © TOSHIBA TEC
2
Original glass
ADF original glass
Mirror-1
Mirror-2
Mirror-3
Reflector
Lens
Exposure lamp
Automatic original detection sensor
Toner cartridge switch
Laser unit
Laser unit cooling fan
Drawer pickup roller
Drawer feed roller
Drawer separation roller
Drawer transport roller
Drawer
Drawer tray
Drawer tray-up sensor
Drawer empty sensor
Drawer paper stock sensor
Drawer damp heater (JPD only)
Registration roller
Registration sensor
Upper drawer feed sensor
Lower drawer feed sensor
Exit sensor
ADU upper transport roller
ADU middle transport roller
ADU lower transport roller
ADU entrance sensor
ADU exit sensor
Bypass pickup roller
Bypass feed roller
Bypass separation roller
Bypass tray
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
Bypass paper sensor
Bypass feed sensor
Temperature/humidity sensor
Transfer charger
Separation charger
Drum
Developer unit
Cleaning blade
Recovery blade
Main charger
Discharge LED
Drum thermistor
Drum damp heater thermostat
Drum damp heater
Separation finger for drum
Toner bag full detection sensor-2
Auto-toner sensor
Toner recovery auger
Developer sleeve (magnetic roller)
Heat roller
Pressure roller
Cleaning roller
IH coil
Main thermistor / Edge thermistor
Separation finger for heat roller
Separation finger for pressure roller
Exit roller
Fuser thermostat
Middle fan
Exhaust fan
Sub-separation fan
Power supply cooling fan
Main switch
Front cover opening/closing switch
Cover opening/closing interlock switch
Polygonal motor

November 2003 © TOSHIBA TEC 2 - 3 e-STUDIO350/450 OUTLINE OF THE MACHINE
2
Fig. 2-102
3
2
5
4
7
6
98
15
14
17
16
28
13 12
11 10
20
21
19
18
23 22 25
24 26 27 26
1

e-STUDIO350/450 OUTLINE OF THE MACHINE 2 - 4 November 2003 © TOSHIBA TEC
2
Platen sensor
Scan motor
Carriage home position sensor
Scanner damp heater (Left)
Scanner damp heater (Right)
Scanner damp heater thermostat
IH board cooling fan
Developer unit cooling fan-1
Toner motor
Developer drive clutch
Main motor
Exit motor
Toner bag full detection sensor-1
ADU opening/closing switch
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Fuser unit cooling fan
Registration clutch
ADU motor
ADU clutch
Bypass pickup solenoid
Bypass feed clutch
Side cover opening/closing switch
Transport clutch (High speed)
Transport clutch (Low speed)
Lower drawer feed clutch
Tray-up motor
Drawer detection switch
Upper drawer feed clutch
Developer unit cooling fan-2