Toshiba Carrier RBC-AX22CUL User manual

ADR
Signal receiving unit
Wireless remote controller
(WX-TA01UES)
REMOTE CONTROLLER FOR AIR CONDITIONER (SPLIT TYPE)
Installation Manual
Remote Controller
Model name :
Wireless remote controller kit
RBC-AX22CUL
Installation Manual 1
Remote controller for air conditioner (Split type)
Manuel D’installation 8
Télécommande pour climatiseur (Type split)
English
Français
Generic
model name
RBC-AX22CUL
Wireless remote controller
and signal receiving unit
WX-TA01UES
(Wireless remote controller model name)

1
Wireless remote controller kit Installation Manual
Thank you very much for purchasing TOSHIBA/Carrier Remote Controller for Air Conditioner.
Please read the owner's manual carefully before using your Remote Controller for Air Conditioner.
• Be sure to obtain the “Owner’s manual” and “Installation manual” from constructor (or dealer).
Request to constructor or dealer
Please clearly explain the contents of the Owner’s manual and hand over it.
1 ACCESSORY PARTS
No.
1
2
3
4
Accessory
Signal receiving unit
Remote controller
Remote controller holder
Battery
Q’ty
1
1
1
2
No.
5
6
7
Accessory
Owner’s Manual
Installation Manual
Truss tapping screw,
Ø0.16” × 0.63” (M4 ×16mm)
Q’ty
1
1
2
English-1
CONTENTS
1 ACCESSORY PARTS ........................................................................................... 1
2 INSTALLATION OF SIGNAL RECEIVING UNIT ................................................. 2
3 HOW TO PERFORM CABLING OF SIGNAL RECEIVING UNIT ........................ 4
4 REQUIREMENT .................................................................................................... 4
5 HOW TO SET THE ROOM TEMPERATURE SENSOR ........................................ 5
6 HOW TO SET THE ADDRESS SWITCH .............................................................. 5
7 SLIDE SWITCH .................................................................................................... 5
8 SELF-DIAGNOSIS TABLE AND MEASURES ..................................................... 5
9 HOW TO SET UP FOR THE HIGH CEILING ........................................................ 6
10 HOW TO HANDLE THE REMOTE CONTROLLER .............................................. 6
11 CAUTIONS FOR INSTALLATION OF THE REMOTE CONTROLLER ............... 6
12 EXPLANATION TO CUSTOMERS ....................................................................... 6
13 TEST RUN ............................................................................................................ 7

2
Wireless remote controller kit Installation Manual
Wire guard
2INSTALLATION OF SIGNAL RECEIVING UNIT
1. Removal of suction grille
1) Slide the suction grille fixing knobs (2 positions)
toward the arrow direction, and then open the
suction grille. (Fig. A)
English-2
Suction grille
Suction grille
fixing knob
Slide
2) Remove the screws (2 pcs.) which are fixing
the wire guard. Using clamps mounted to the
wire guard, hang up the wire guard.
∗Do not remove the fixing screws of clamps of
the indoor unit.
Fig. B
Fig. A
NOTE
After installation of the signal receiving unit, be sure
to mount the wire guard as original. (Fig. C) Fig. C
Clamps
Screws
En

3
Wireless remote controller kit Installation Manual
Panel Side panel
Suction grille
Screw
Cord clamp
Signal receiving unit
Flat head screw driver
(Lap it with vinyl tape.)
Cover
Vinyl tape
Insert it into groove at
the side under circle
mark on the cover.
Cord clamp Cord clamp
High voltage wires
and earth line
Lead wire from the
signal receiving unit
Hole for signal receiving unit wires
3) Remove a screw, move the side panel toward you (direction of arrow), and then remove the side panel.
(Fig. D)
4) Lap the end of flat head screw driver with vinyl tape, and forcedly insert it into the groove at the side under
circle mark on the cover. (Be careful not to damage the panel.) (Fig. E)
5) Pass the lead wire through the panel, and install
the signal receiving unit to the panel hole.(Projection of the signal receiving unit is fixed by the panel hole.)
6) Fix the lead wire of the signal receiving unit to the cord clamp which fixes the cables of the louver motor.
(Fig. F)
7) Install the side panels, with screws as original.
8) Put the lead wire from the signal receiving unit along cables of the louver motor and others, and then fix it
with the cord clamp. (Fig. G)
∗It’s connected to a connection of Remote control wire through a hole for Remote control wire.(Fig. H)
9) After all connections have been made, install wire guard and suction grill before doing the “TEST RUN”.
Fig. D
Fig. F Fig. G
NOTE 1
Avoid to twist cables of the sensor with the
power cables, otherwise a malfunction is caused.
∗For cabling and TEST RUN, refer to “HOW TO
PERFORM CABLING OF SIGNAL RECEIVING
UNIT”of these sheets and “TEST RUN”of the
Installation manual attached to the indoor unit.
Fig. H
Fig. E
English-3

4
Wireless remote controller kit Installation Manual
3HOWTO PERFORM CABLING OF SIGNAL RECEIVING UNIT
Connection diagram
Connection
•Connect the cables out of the signal receiving unit
to the terminal block for remote controller cabling of
the indoor unit. (There is no polarity.)
CN001
2P White
Indoor unit Signal receiving unit
P.C. board
Terminal block for
remote controller
cabling White
Black
4REQUIREMENT
The control by two remote controllers is enabled by installing the wireless remote controller with the wired remote
controller for an indoor unit. (Max. 2 remote controllers of wireless or wired are installable.)
“2-remote controllers”controlling means that one or multiple units are operated by the multiple remote controllers.
NOTES
1. Upon confirmation of the terminal numbers of the indoor unit, connect the remote controller cables without
miscabling.(If applied AC 208/230 Volt, damage the unit.)
2. The multiple wireless remote controller kits cannot concurrently be used for an indoor unit.
3. When installing simultaneously the wireless remote controller with the wired remote controller, set one of them
as the sub remote controller.
•When setting the wired remote controller as the sub, exchange the address connector at the rear of P.C.
board of wired remote controller from main to sub remote controller.
•When setting the wireless remote controller as the sub, turn No.3 of DIP switch [S003] on P.C. board of
signal receiving unit from OFF to ON.
To operate an indoor unit by
2 remote controllers
∗The indoor unit is operated if
either wireless or wired remote
controller is set as main or
sub remote controller.
(Total cable length:Within 1312’4”(400m))
To operate a group control of multiple indoor units
by 2 remote controllers
∗Main and Sub remote controllers
are operable even if they are installed
to any indoor unit.
(Total cable length:Within 656’2”(200m))
English-4
Earth
Wireless
remote controller kit
(Main)
CN001
Wired
remote controller
(Sub)
21 (Sold
separately)
Terminal block for
remote controller cable
Remote controller cable
(Procured locally)
AWG20 (0.5mm²)
Indoor unit
Use UL wires
rated 300V
2
1
Signal receiving unit
Earth Earth Earth
(Sold
separately)
Terminal block for
remote controller
cable
Remote controller inter-unit
cable for group control
(Procured locally)
AWG20 (0.5mm²)
Use UL wires rated 300V
2
1
Wired
remote controller
(Sub)
Wireless
remote controller kit
(Main)
CN001 21
Indoor unit
No.1 Indoor unit No.2 Indoor unit No.3
Earth
Indoor unit
No.N
Signal
receiving unit

5
Wireless remote controller kit Installation Manual
5 HOW TO SET THE ROOM TEMPERATURE SENSOR
• The room temperature sensors are equipped in the indoor unit and the wireless remote controller.
One of two sensors works.
• The room temperature sensor is set to the indoor unit side at the shipment from the factory.
To select the sensor in the remote controller, push the SENSOR button (Right figure) inside of the remote
controller cover and check “ ” disappears from LCD.
7 SLIDE SWITCH
• Check the slide switch in the battery box of
the remote controller is set to [S] / [A] at
shipment from the factory.
Do not change the setting.
8 SELF-DIAGNOSIS TABLE AND
MEASURES
SKNAHC
Select of operation
mode set to A.
Select of louver
indication set to S.
AHC
SKN
6 HOW TO SET THE ADDRESS SWITCH
• When the multiple signal receiving units are installed in the same room, an address can be set to prevent cross
communication.
• When replacing the battery and pushing ACL button, the address of the remote controller becomes [ALL] and the
signal receiving unit is enabled to receive signal regardless of setting of address switch of the operation section.
• For selecting of the remote controller address, refer to Owner’s Manual.
• Change the address of the
signal receiving unit by removing
screws of P.C. board cover of the
signal receiving unit.
After then, fix the cover with
screws using a clamp.
NOTE
If the room temperature data from the remote controller is not transmitted to the
unit for 10 minutes or more, the sensor at indoor unit side is automatically selected
even if the sensor at the remote controller side is selected.
Fix the remote controller toward the unit as possible.
Display of
remote controller
address
Address switch
position of signal
receiving unit
∗Address switch of
signal receiving
unit can be set
any position.
Address Address Address Address
1 2 3
4 5 6
1 2 3
4 5 6
1 2 3
4 5 6
English-5
LEDs on the
signal receiving unit
: Off
: Blinking
(at intervals of 0.5 sec.)
Lamp indication
No indication even if
the remote controller
is operated.
Cause
Power supply is not
turned on.
Miscabling between
signal receiving unit and
indoor unit
Defective connection
between signal receiving
unit and indoor unit
Miscabling or defective
connection between
indoor and outdoor units
Protective device of
outdoor unit works.
Protective device of
indoor unit works.
Measures
Check cable
connection
and correct it.
Check
outdoor unit.
Check
indoor unit.
Blinks alternatively
Blinks alternatively

6
Wireless remote controller kit Installation Manual
9 HOWTO SET UP FORTHE HIGH CEILING
•When the height of ceiling to be installed with a filter exceeds 11’6”
(3.5m), tap-up of DC fan is required.
Tap-up of DC fan can be set at No.2 (Tap 1) and No.4 (Tap 2) of DIP switch
[S003] on the signal receiving unit P.C.board.
The signal receiving unit P.C. board appears by removing screws at
the rear side of the signal receiving unit and the rear cover.
Setup for high ceiling
NOTE
Never set ON to DIP switch [S003] No.1 (TEST RUN).(A TEST RUN is carried out on the remote controller.)
(For the TEST RUN, refer to the Installation manual attached to the indoor unit.)
[S003] No.2 (Tap 1) and
[S003] No.4 (Tap 2) are used.
Standard (At shipment)
Type 1
[S003] No.2
(Tap 1)
OFF
OFF
[S003] No.4
(Tap 2)
OFF
ON
Installable height
of ceiling
11’6”(3.5m)
13’1”(4.0m)
10 HOWTO HANDLETHE REMOTE CONTROLLER
•In case using remote controller mounting to the wall, etc.
Check a signal is received correctly by pushing button at the position to be fixed.
ON
12 3 4
2 3 4
1
2
Mounting screw
Truss tapping
Ø0.16” × 0.63”
(M4 × 16mm)
•To take off remote controller,
pull it toward you.
Put on.
Push.
ACL button
Cover
11 CAUTIONS FOR INSTALLATION OFTHE REMOTE CONTROLLER
•To operate the remote controller by fixing it to the wall, etc. with a remote controller holder, turn on the
fluorescent lamp, operate the remote controller at the position to be fixed, check the air conditioner normally
operates, and then mount it.
•When the room temperature is sensed by the remote controller, mount the remote controller paying attention to
the following items.
•Place not exposed directly to cold or hot wind.
•Place not exposed directly to the sunlight.
•Other places where the remote controller is not influenced.
12 EXPLANATIONTO CUSTOMERS
•Hand over the “Owner’s Manual”and “Installation Manuals”to the customer after installation works.
•Explain usage and maintenance of the remote controller according to “Owner’s Manual”.
English-6
•Replacement of battery
1. Holding the both ends of the cover and
remove it by sliding downward.
2. Correctly insert 2 AAA alkali batteries
matching + and - polarities with
indications.
3. Push ACL button with something
tipped and attach the cover.

7
Wireless remote controller kit Installation Manual
13 TEST RUN
nBeforeTEST RUN
•Before turning on the power supply switch, carry out the following procedure.
1) Using 500V-megger, check 1MΩor more exists between the terminal block 1 to 3 and the earth.
If 1MΩor less is detected, do not run the unit. Do not apply to the remote controller circuit.
2) Check the valve of the outdoor unit being opened fully.
•To protect the compressor at activation time, leave power-ON for 12 hours or more be for operating.
nHow to execute aTEST RUN
Using the remote controller, operate the unit as usual.
For the procedure of the operation, refer to the attached Owner’s Manual.A forced TEST RUN can be
executed in the following procedure if the operation stops by thermo.-OFF. In order to prevent a serial
operation, the forced TEST RUN is released after 60 minutes have passed and returns to the usual operation.
CAUTION
When the remote controller is used for the first time, it accepts an operation approx. 5 minutes after the power
supply has been turned on. It is not a trouble, but is because the setup of the remote controller is being checked.
For the second power-ON time and after, approx.1 minute is required to start the operation by the remote controller.
ADR
Be sure to set the
air speed to [ ].
2 3, 4, 5,
6
2, 7
NOTE
Do not use the forcedTEST RUN for cases other than
the TEST RUN because it applies an excessive load
to the devices.
uIn case of wireless remote controller
Procedure
1
2
3
4
5
6
7
Operation contents
Turn on power of the set.
After installation, the operation is not accepted for 5 minutes when the power has been turned on at
the first time, and 1 minute when the power has been turned on at the second time and after.
Perform a test run after a specified time has passed.
Push [ ] button on the remote controller, change the operation mode to [ ] or [ ] by using [ ]
button, and then change the air speed to [ ] by [ ] button.
Cooling test run Heating test run
Set temperature to 64°F (18°C) by using [ ] button. Set temperature to 86°F (30°C) by using [ ] button.
Push [ ] button to set temperature to 66°F (19°C) Push [ ] button to set temperature to 84°F (29°C)
just after confirming the receiving sound “Pi”. just after confirming the receiving sound “Pi”.
Push [ ] button to set temperature to 64°F (18°C) Push [ ] button to set temperature to 86°F (30°C)
just after confirming the receiving sound “Pi”. just after confirming the receiving sound “Pi”.
Repeat the procedure 4→→
→→
→5→→
→→
→4→→
→→
→5.
After approx.10 seconds, all the display lamps [ ] (Green), [ ] (Green), and [ ] (Yellow) of the
wireless sensors flash, and the operation starts.
If the lamps do not flash, repeat the procedure 2and after.
When the TEST RUN has finished, push [ ] button to stop the operation.
English-7

85464369215000
(EH99677401)