Toshiba RB-RXS33-E User manual

WIRELESS CONTROLLER
OPERATION MANUAL
For general public use
RB-RXS33-E
ENGLISH
1112150138

EN CONTENTS
1. PREPARATION BEFORE USE .................................................................................................................................................1
2. REMOTE CONTROL.................................................................................................................................................................1
3. AUTOMATIC / COOLING (DRY) / HEATING / FAN ONLY OPERATION ..................................................................................1
4. Hi POWER OPERATION...........................................................................................................................................................1
5. ECO OPERATION .....................................................................................................................................................................1
6. TIMER OPERATION..................................................................................................................................................................1
7. PRESET OPERATION ..............................................................................................................................................................2
8. FIREPLACE AND 8°C HEATING OPERATION.........................................................................................................................2
9. COMFORT SLEEP OPERATION ..............................................................................................................................................2
10. FILTER RESET..........................................................................................................................................................................2
11. HADA CARE FLOW OPERATION.............................................................................................................................................2
12. DISPLAY LAMP BRIGHTNESS ADJUSTMENT........................................................................................................................2
13. REMOTE CONTROL A-B SELECTION.....................................................................................................................................3
14. POWER-SELECTION AND SILENT OPERATION (OUTDOOR UNIT).....................................................................................3
15. WEEKLY TIMER OPERATION ..................................................................................................................................................3

1
PREPARATION BEFORE USE1
REMOTE CONTROL2
Hi POWER OPERATION
4
ECO OPERATION5
TIMER OPERATION6
AUTOMATIC / COOLING (DRY) /
HEATING / FAN ONLY OPERATION
3
Preparing Filters
1. Open the air inlet grille and
remove the air filters.
2. Attach the attachment filters
(see detail in the accessory
sheet).
Loading Batteries
1. Remove the battery cover.
2. Insert 2 new alkaline batteries
(AAA type) following the (+)
and (–) positions.
Removing the batteries
1. Remove the cover, and take out the batteries.
2. Reattach the cover.
• Please dispose of the batteries according to
the local regulation.
Clock Setup
1. Push by tip of the pencil.
If timer indication is flashing, go to
the next step 2.
2. Press or : adjust the time.
3. Press : Set the time.
Remote Control Reset
1. Remove the batteries.
2. Press .
3. Insert the batteries.
Remote Control Caring
1. Clean the remote control with a wet cloth when needed.
2. No benzine, thinner, polishing powder or chemically-
treated duster.
1. Press : Select Auto A, Cool , Dry , Heat ,
or Fan only .
2. Press : Set the desired temperature.
Min. 17°C, Max. 30°C.
3. Press : Select AUTO, LOW , LOW+ ,
MED , MED+ , HIGH and QUIET .
w AUTOMATIC OPERATION : Choose cooling or heating
operation automatically.
w In DRY OPERATION mode, it can not select air volume.
w In FAN ONLY OPERATION mode, it does not show
setting temperature.
To automatically control room temperature and airflow for
faster Auto, cooling or heating operation (except in DRY
mode).
Press : Start and stop the operation.
To automatically control room temperature to save energy
(except in DRY mode).
Press : Start and stop the operation.
Note: Cooling operation; the internal set temperature will
increase automatically 1 degree by 2 hours (maximum
2 degrees increase). For heating operation the internal
set temperature will decrease.
Set the timer when the air conditioner is operating.
Setting the ON Timer Setting the OFF Timer
1Press : Set the
desired
ON timer.
Press : Set the
desired
OFF timer.
2Press : Set the
timer.
Press : Set the
timer.
3Press : Cancel
the timer.
Press : Cancel
the timer.
Setting the ON-OFF Timer
1Press : Set the ON
timer.
3Press .
2Press : Set the
OFF timer.
4Press :
Cancel the timer.
Note:
• Keep the remote control in accessible transmission to the
indoor unit; otherwise, the time lag of up to 15 minutes
will occur.
• The setting will be saved for the next same operation.
Note:
• The provided Remote Controller is a wireless type, which
also can be used as a wire. Please see “How to Connect
The Remote Controller for Wired Operation”, located in
installation instruction, in case of wired control is required.
• In wire operation, remote controller will return to initial
condition (PRESET, TIMER and CLOCK will return to initial
condition) when user shutdown power supply of
Air conditioner.
1
Infrared signal emitter
2
Memory and Preset button (PRESET)
3
Start/Stop button
4
Mode select button (MODE)
5
Air flow/HADA CARE FLOW button
6
Fireplace/8°C button
7
ECO button
8
Comfort sleep button (COMFORT SLEEP)
9
Weekly timer (ON/OFF)
!
Temp for Weekly timer
"
On timer button (ON)
#
Set clock button (CLOCK)
$
Check button (CHECK)
%
Filter reset button (FILTER)
&
Temperature button (TEMP)
(
Swing louver button (SWING)
)
Fan speed button (FAN)
~
Set louver button (FIX)
+
High power button (Hi POWER)
,
Power selection/Silent button (P-SEL/SILENT)
-
Program P1 - P4
.
Day/Edit button
/
Setup button (SET)
:
Off timer button (OFF)
;
Clear button (CLR)
<
Reset button (RESET)
Insert direction of
(+) and (-) correctly
Pull the cover
away firmly.
1
-
2
3
4
6
5
(
%
&
"
7
!
9
<
8
#
)
$
/
,
~
+
:
;
.

2
PRESET OPERATION7
FIREPLACE AND 8°C HEATING OPERATION 8
COMFORT SLEEP OPERATION9
FILTER RESET10
HADA CARE FLOW OPERATION11
DISPLAY LAMP BRIGHTNESS ADJUSTMENT 12
Set your preferred operation for future use. The setting will
be memorized by the unit for future operation (except airflow
direction).
1. Select your preferred operation.
2. Press and hold until stop blinking and the P
mark displays.
3. Press : Operate the preset operation.
Fireplace Operation ( )
Keep indoor unit’s fan blowing continuously during thermo off,
to circulate heat from other sources over the room.
There are three setting parameters:
Default setting > Fireplace 1 > Fireplace 2
Fireplace 1:
During thermo off period, the indoor unit’s fan will continue to
run by the same speed, previously selected by end-user.
Fireplace 2:
During thermo off period, the indoor unit’s fan will continue to
run at super-low speed, programmed from factory.
8°C Heating Operation (8°C)
Heat mode operation for keep room temperature (5-13°C) with
less of energy usage.
Fireplace and 8°C Heating Operation
8°C
FIREPLACE 1 FIREPLACE 2
Normal
operation
Note:
• While Fireplace operation on heating mode, indoor unit
fan always runs and cold air breezing might be occurred.
• Fireplace and 8°C will operate in Heating mode only.
For comfortable sleep, automatically control air flow and
automatically turn OFF (Except in DRY mode and Fan only
mode).
1. Press : Select 1, 3, 5 or 9 hrs for OFF timer
operation.
2. Press to cancel the comfort sleep operation.
Note: The cooling operation, the set temperature will increase
automatically 1 degree/hour for 2 hours (maximum
2 degrees increase). For heating operation, the set
temperature will decrease.
Firstly, turn off the circuit breaker.
FILTER lamp lights on; the filter must be cleaned.
To turn off the lamp, press RESET button on the indoor unit
for Hi-wall or ON/OFF button for Bi-flow console, also can
push the FILTER button on the remote control in another way.
(Please follow the instructions in the air conditioner owner’s
manual.)
HADA CARE FLOW
Air flow upward to the ceiling, provide Indirect air flow to body
and homogenize room temperture.
HADA CARE FLOW operation
Press For start and stop HADA CARE FLOW
Cancel
HADA CARE FLOW
HADA CARE FLOW
Note:
• During HADA CARE FLOW mode, FIX and SWING
button cannot active
To decrease the display lamp brightness or turn it off.
1. Press and hold
)$1
for 3 seconds until brightness
level ( , , or ) is shown on remote control LCD
then release the button.
2. Press Rise or
Decrease
to adjust brightness
in 4 levels.
Remote
control LCD Operation display Brightness
Lamp illuminates full brightness.
100%
Lamp illuminates 50%
brightness.
50%
Lamp illuminates 50%
brightness and the operation
lamp is turned off.
50%
All lamps are turned off.
All turned
off
• In the examples of and , the lamp illuminates for 5
seconds before going off.

3
REMOTE CONTROL A-B SELECTION13
POWER-SELECTION AND SILENT
OPERATION (OUTDOOR UNIT)
14
To separate using of remote control for each indoor unit in
case of 2 air conditioners are installed nearly.
Remote Control B Setup.
1. Press RESET button on the indoor unit to turn the air
conditioner ON for Hi-wall type or press and hold MODE
button on the indoor unit more than 20 seconds for
Bi-flow console type. (Please follow the instructions in the
air conditioner owner’s manual.)
2. Point the remote control at the air conditioner.
3. Push and hold button on the Remote Control by
the tip of the pencil. “00” will be shown on the display.
(Picture 1)
4. Press during pushing . “B” will show on the
display and “00” will disappear and the air conditioner will
turn OFF. The Remote Control B is memorized.
(Picture 2)
Note: 1.Repeat above step to reset Remote Control to be A.
2.Remote Control A has not “A” display.
3.Default setting of Remote Control from factory is A.
12
Power-Selection ( )
This function is used when the circuit breaker is shared with
other electrical appliances. It limits the maximum current
and power consumption to 100%, 75%, or 50% and can be
implemented by POWER-SELECTION. The lower percentage,
the higher saving and also longer compressor lifetime.
Note:
• When the level is selected, POWER-SEL level flashes on
remote LCD display for 3 seconds.
In case of 75% and 50% level, number “75” or “50” also
flashes for 2 seconds.
• Due to the reason that POWER-SELECTION function
limits the maximum current, inadequate cooling or
heating capacity may occur.
Silent Operation ( )
Keep outdoor unit operating silently to ensure either yourself
or neighborhood will have a tight sleep in nighttime. By this
feature, the heating capacity will be optimized to deliver such
silent experience. The silent operation can be selected from
one of two purposes (Silent 1 and Silent 2).
There are three setting parameters: Standard level > Silent 1
> Silent 2
Silent 1:
Though operating silently, the Heating (or Cooling) capacity
is still prioritized to ensure having sufficient comfort inside the
room.
This setting is a perfect balance between the Heating
(or Cooling) capacity and the Sound level of outdoor unit.
Silent 2:
Compromising the Heating (or Cooling) capacity to the Sound
level in any circumstance where the outdoor unit’s sound level
is highly prioritized.
This setting has a purpose to reduce the maximum sound level
of outdoor unit by 4 dB(A).
WEEKLY TIMER OPERATION15
How to set WEEKLY TIMER
1. Press to enter WEEKLY TIMER
setting.
Blink
2. Press to select desired day in
sequence.
The sequence of day symbol appears on the
LCD.
SU tMO tTU tWE tTH tFR tS
A
WEEKLY SUMO
TUWETHFRSA
(All day)
3. Press to select the program number.
• The program 1 is ready for setting while
is pressed PG-1 appears on the
LCD.
• Press to change the program
number in the sequence program 1 to
program 4.
PG-1
PG- 2
PG- 3
PG- 4
4. Press or to select the desired
time.
• The time can be set between 0:00 and 23:50
in 10 minute intervals.
• Press and hold the button to change setting
time for 1 hr.
• Only one of ON or OFF timer can be set on
each program.
ON timer display OFF timer display*
*OFF timer is used to stop the air conditioner
only. The display does not show Operation
mode, Temperature, Fan speed and others.
Note:
• While activating of Silent operation, inadequate heating
(or cooling) capacity may occur.
Power-Selection and Silent Operation (Outdoor Unit)
[100%] [75%] [50%]
SILENT#2 SILENT#1

4
5. Press to select desired operation.
6. Press or to select desired temperature.
• The temperature can be set between 17°C and 30°C.
7. Press to select the desired fan speed.
8. Add operations, if required.
• Press to use 8°C operation.
(Notes: Fireplace cannot select and memorize in weekly
function)
• Press to use ECO operation.
• Press to use Hi POWER operation.
• Press to use Silent operation.
9. Adding or editing the program.
The program can be set to perform on all the required days
until is pressed to confirm the setting 10. If adding or
editing a program is required, please repeat steps 2 - 8 before
setting confirmation.
10. After adding or editing, press to confirm the setting*.
Operating Mode
Weekly timer running
Next program
Timer ON or OFF
Next operation time Operating Temperature and
Fan speed
Display after
pressing SET button
*Point remote control at air conditioner receiving module then,
press SET button until you hear the “PiPi” sound. This means
the setting operation has been completed. As the air conditioner
is receiving the signal, you will hear separate “Pi” sounds
corresponding to the number of days in the selected setting.
An incomplete setting is indicated if the TIMER lamp is blinking.
Press twice.
Notes:
1. Place the remote control where the indoor unit can receive the
signal. This will increase the accuracy of the timing between
the remote control and the air conditioning unit.
2. The ON/OFF timer can be set during the WEEKLY TIMER
operation. In this situation, the air conditioner will first follow
the normal timer until it is complete; then, it will return to the
WEEKLY TIMER function.
3. During WEEKLY TIMER operation, all of operation such
as MODE, TEMP, FAN, Hi POWER, ECO and etc., can be
adjusted but when the clock reaches the program setting, the
operation will return to the set items in the program.
4. When the remote control is sending a signal to the air
conditioner, avoid interference from objects that can block the
signal.
Edit Weekly timer program
To edit the program after confirming the weekly
timer setting, follow steps 1 - 3 below.
1. Press .
• The day of the week and the program
number of the current day will be displayed.
2. Press to select the day of the week
and press to select program number
to be confirmed.
• Resetting the operation.
3. Press to exit confirming mode.
Deactivating WEEKLY TIMER operation
Press while “WEEKLY” is displayed on
the LCD.
• The “WEEKLY” indicator will disappear from
the LCD. However, the program will remain in
the remote control.
• The TIMER lamp goes off.
• To reactivate the WEEKLY TIMER operation
again, press again, LCD shows the
next program. The program, after reactivation,
is related to the clock time.
To delete programs
The individual program
1. Press .
• The day of the week and the program
number is displayed.
• Select the day to delete the program.
2. Press to select the program number to
be deleted.
3. Press .
• ON or OFF timer will be cleared and the
LCD will blink.
4. Press to delete the program.
• Press while the LCD is blinking.
The program has now been deleted.
All programs
1. Press .
• The day of the week and the program
number will be displayed.
2. Press and hold for 3 seconds.
• All programs will be deleted and LCD
displays current operation.
Notes :
Make sure the remote control receiving module
on the air conditioner receives the signal from the
remote control.

Information according to EMC Directive 2004/108/EC
(Name of the manufacturer) TOSHIBA CARRIER (THAILAND) CO., LTD.
(Address, city, country) 144/9 MOO 5, BANGKADI INDUSTRIAL PARK,
TIVANON ROAD, TAMBOL BANGKADI, AMPHUR
MUANG, PATHUMTHANI 12000, THAILAND.
(Name of the Importer / Distributor in EU) TOSHIBA CARRIER UK LTD.
(Address, city, country) Porsham Close, Belliver Industrial Estate, PLYMOUTH,
Devon, PL6 7DB. United Kingdom