Toshiba RBC-AX33UYP-E User manual

‒1 ‒
INSTALLATION MANUAL
To Qualified Installer in Installation Work and Service
Wireless receiver kit
Model: RBC-AX33UYP-E
• Thank you for purchasing Wireless receiver kit for TOSHIBA air conditioners.
• Read this manual carefully for correct installation of the Wireless receiver before
starting work.
• After the installation is completed, execute a test run to check for normal operation
and explain how to use and maintain the Wireless receiver to the customer according
to the Owner’s Manual.
Ask the customer to keep this manual with the Owner’s Manual.
Observe the safety precautions described in the Installation manual supplied with the
ceiling panel and air conditioner (indoor unit).
Accessories
Part Name Q’ty
Wireless receiver
1
Wireless remote
controlle 1
Remote controller
holder 1
Part Name Q’ty
Operation Manual 1
Installation Manual
(this manual) 1
CD-ROM
1
Batterry 2
Flat head wood screw
Ø3.1 x 16R 2
Settings for the Wireless receiver before installation
Before installing the Wireless receiver, make the following setting referring to each
description.
• To install the wireless remote controller together with wired remote controller,
configure the “Multiple remote controller installation”
• When ceiling height exceeds the standard height (factory default), refer to the
“Installing indoor unit on high ceiling” on installation manual of the indoor unit.
How to install the Wireless receiver
Install the Wireless receiver
in correct orientation, since
the Wireless receiver can be
installed at only one corner
as shown in. (Fig. 1)
1. Remove the adjust corner
cap at the corner where the
Wireless receiver is to be
installed. (Fig. 2)
• Pull the edge of the adjust corner cap
in the direction of arrow.
• Remove strap from the pin and detach
the adjust corner cap from the ceiling panel.
(Fig. 2)
Pull
Adjust corner cap
Ceiling panel
Pin
Strap
2. Wiring the wireless receiver lead wire through to the clamp in the back side of the
ceiling panel.
Wireless receiver wire
Clamp Clamp
3. Attach the Wireless receiver cap to the ceiling panel.
• Hook the strap of the Wireless receiver cap securely to the pin.
• Insert the two claws A of the Wireless receiver cap into the rectangular holes of the
ceiling panel in the direction of arrow.
• Push the Wireless receiver cap so that the two claws B
on the back of the cap are fitted.
Pin
Claws A
Claws B Wireless receiver cap
Strap
Push
CAUTION
Press the two claws B of the adjust corner cap firmly as far as they will go, and
then check that the adjust corner cap is closely attached.
Failure to do so may result in water leakage.
4. Connecting wires of Wireless receiver.
• Remove the screw of the electrical control box cover, and detach the electrical
control box cover by slide.
(The eletrical control box cover is clamped onto the hinge.)
• Pass the wireless receiver wire from the ceiling panel through the clamper as shown,
and connect the wire to connector CN214 on the P.C. board of the indoor unit.
* Connect the wire firmly to the connector to ensure operation of the Wireless
receiver.
• Attach the electrical control box cover by reversing the procedure of detaching.
* Make sure that no wire is caught between the electrical control box and the
cover.
* Make sure that no wire is caught between the indoor unit and the ceiling
panel.
Electric control
box cover
CN214 Clamper
Pass the wire
through the clamper
as illustrated.
Wireless receiver wire
Screw
Wire Connection (For illustrative purpose the orientation of the indoor unit is not the actual orientation)
(Fig. 1)
Wireless receiver
installing position
(English)

‒2 ‒
Remote controller address (A-B selection) setting
• When two or more wireless receiver are installed in a room, a unique address can be
set for each wireless receiver to prevent interference.
• Address (A-B selection) must be changed on wireless remote controller.
Test run (Forced cooling operation)
Requirement
• Finish the forced cooling operation in a short time because it applies excessive
strength to the air conditioner.
How to perform forced cooling operation
1. When TEMPORARY button is pushed for 10 seconds or more, “Pi!” sound is heard
and the operation changes to a forced cooling operation. After approx.
3 minutes, a cooling operation starts forcedly. Check cool air starts blowing.
If the operation does not start, check wiring again.
2. To stop a test operation, push TEMPORARY button once again (Approx. 1 Sec.).
• Check wiring / piping of the indoor and outdoor unit in forced cooling operation.
TEMPORARY
button
Preparation and check before use
1. Loading Batteries
• Remove the battery cover.
• Insert 2 new batteries (R03 [AAA])
following the (+) and (-) positions.
2. Removing Batteries
• Remove the battery cover.
• Remove the 2 used batteries.
Batteries
• To replace the batteries, use two new batteries (R03 [AAA]).
• In normal use, the batteries will last about one year.
• Replace the batteries if there is no receiving beep from the indoor unit or when the air
conditioner cannot be operated using the remote controller.
• To avoid malfunctions by battery leakage, remove the batteries when not using the
remote controller for more than one month.
• Please dispose of the used batteries according to the local regulation.
Installing the remote controller holder
• Before you actually install the remote controller holder on a wall or pillar, check
whether the remote controller signals can be received by the indoor unit.
Flat head
wood screw
Remote control holder
Mounting and removing the remote controller
• To mount the remote controller hold it parallel to the remote controller holder and
push it in fully. To remove the remote controller slide the remote controller upwards
and out from the holder.
Self-diagnosis function and measures
• The following table shows a few examples. For details of indoor unit errors, refer to
the Installation Manual of the indoor unit.
LED Possible cause Measures
These LEDs do not light or
blink even if the remote
controller is operated.
- Power is not turned on.
- Incorrect connection between
signal receiving unit and
indoor unit
Check connections and
reconnect wires correctly, if
necessary.
Loose connection between
signal receiving unit and indoor
unit
Incorrect or loose connection
between indoor unit and
outdoor unit
The protective device of the
outdoor unit is activated. Check the outdoor unit.
The protective device of the
indoor unit is activated. Check the indoor unit.
LEDs on the signal receiving unit : OFF : Blinking (at intervals of 0.5 seconds)
Notes on installing remote controller
• When using a wireless remote controller in the remote controller holder on a wall, turn
on a fluorescent light and operate the remote controller at the installation position.
Make sure that the air conditioner operates normally and then secure the remote
controller holder on the wall.
• When installing a remote controller that senses room temperature with the sensor,
avoid the following places.
• A place exposed to direct cool air, warm air or direct sunlight.
• A place subject to thermal effects.
Explanation to the customer
• After the installation work has been completed, execute a test run to check for normal
operation and then hand the customer the Owner’s Manual and Installation Manual of
the wireless remote controller kit.
• Explain how to use and maintain the wireless remote controller kit to the customer
according to the Owner’s Manual of the wireless remote controller kit.
List of separately available products that cannot be used with
the Wireless receiver kit.
The following separately available products cannot be used together with the
Wireless receiver kit.
Product name Model
Occupancy sensor kit TCB-SIR41UYP-E
1127699102