Toshiba IK-SX1 User manual

1
For Customer Use
Enter below the Serial No.
which is located on the
bottom of the cabinet. Re-
tain this information for fu-
ture reference.
Model No.: IK-SX1L
IK-SX1
Serial No.:
CCD CAMERA
IK-SX1L/IK-SX1
INSTRUCTION MANUAL
WARNING
This is a Class A of EN55022 product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
INFORMATION
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio com-
munications. Operation of this equipment in a residential area is likely to cause harmful interfer-
ence in which case the user will be required to correct the interference at his own expense.
USER-INSTALLER CAUTION: YourauthoritytooperatethisFCCverifiedequipmentcouldbevoided
if you make changes or modifications not expressly approved by the party responsible for compli-
ance to Part 15 of the FCC rules.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est comforme à la norme NMB-003 du Canada.

2
Safety precautions
Read the following safety precautions carefully before using the product. These instructions
contain valuable information on safe and proper use that will prevent harm and damage to
the operator and other persons. Make sure that you fully understand the following details
(indications, graphic symbols) before proceeding to the main descriptions in this manual.
Indication definitions Graphic symbol definitions
*1: Bodily injury means injuries, burns and
electric shock which does not require hos-
pitalization or prolonged treatment.
*2: Physical damage means extended harm to
home, household effects.
Warning
• Do not use the product when abnormality occurs.
The use in the abnormality status such as emitting smoke from the product, smelling
burning, being damaged by drop, invasion of foreign objects inside the product, etc.,
may cause fire and/or electric shock. Be always sure to disconnect the power plug
from the electrical outlet (socket) at once and contact your dealer.
• Do not install the product where splashing of water may occur, such as outdoor, a
bathroom, etc.
This may cause fire and/or electric shock.
• Do not repair, disassemble and/or modify by yourself.
This may cause fire and/or electric shock. Be always sure to contact your dealer for
internal repair, check and cleaning of the product.
• Keep the rated voltage for the product.
The use of power supply voltage except for its rated voltage may cause fire and/or
electrical shock. Please refer to “4. Connections”.
• Do not put a vessel(s) filled with a liquid (flower vase, etc.).
If a liquid enters the product, a fire and/or electric shock may occur.
• Do not put the product in an unstable, slanting and/or vibrated place.
Drop and/or fail of the product may cause injury.
• Do not touch cords during a thunderstrom.
This might cause electric shock.
Meaning
Indicates a prohibited action that
must not be carried out. The ac-
tual prohibited action is indicated
in the symbol or nearby graphi-
cally or described in text.
Indicates a mandatory action that
must be carried out surely. The
actual mandatory action is indi-
cated in the symbol or nearby
graphically or described in text.
SymbolMeaning
This indicates that ignoring this
label and/or misoperation of the
product may cause serious per-
sonal injury or even death.
This indicates that ignoring this
label and/or misoperation of the
product may cause personal in-
jury*1 and/or material damage*2.
Indication
Warning
Caution

3
Caution
• Keep the followings when installing.
• Do not put the product on a Inflammable material such as carpet or blanket.
• Do not put the product in a narrow space, since the heat generated from the prod-
uct may be difficult to emanate.
• Do not put a inflammable material on the product.
If you do not keep above, the heat generated by the product may cause fire.
• Do not put the product in direct sunshine and/or high temperature.
The temperature rise inside the product may cause fire.
• Do not put the product In a moist or dusty place such as a bathroom, a place close to
a humidifier, etc.
This may cause fire and/or electric shock.
• Do not put the product in a moist, soot and/or dusty place.
Do not put the product where a soot and steam may occur, such as a kitchen, etc., or
in a dusty place. This may cause fire and/or electric shock.
• Do not shoot the sun with the lens and do not put the lens in the place exposed to an
intensive light, such as the sunshine, etc.
Focusing of the light may cause injury of eye and/or fire.
• Do not put the product in your mouse and do not swallow it.
This may cause suffocation and/or injury.
• Ask your dealer to perform a periodical check and internal cleaning (approx. once
every five years).
Dust inside the product may cause fire and/or trouble. For check and cleaning cost,
please consult your dealer.
Disclaimer
We disclaim any responsibility and shall be held harmless for any damages or losses incurred
by the user in any of the following cases:
1. Fire, earthquake or any other act of God; acts by third parties; misuse by the user, whether
intentional or accidental; use under extreme operating conditions.
2. Malfunction or non-function resulting in indirect, additional or consequential damages,
including but not limited to loss of expected income and suspension of business activities.
3. Incorrect use not in compliance with instructions in this instruction manual.
4. Malfunctions resulting from misconnection to other equipment.
5. Repairs or modifications made by the user or caused to be made by the user and carried
out by an unauthorized third party.
6. Notwithstanding the foregoing, Toshiba’s liabilities shall not, in any circumstances, exceed
the purchase price of the product.

4
TABLE OF CONTENTS
1. CAUTIONS ON USE AND INSTALLATION................................................ 5
2. COMPONENTS ............................................................................................ 5
3. CAMERA PARTS AND FUNCTIONS........................................................... 6
4. CONNECTIONS............................................................................................ 7
4.1. Standard Connection........................................................................... 7
4.2. Cautions on Connection...................................................................... 7
4.3. Connector Pin Assignments ............................................................... 7
5. OPERATION.................................................................................................. 8
6. Setting .......................................................................................................... 9
6.1 Gain switch ........................................................................................... 9
6.2 Synchronizing mode selector switch................................................. 9
6.3 Mode setting switch ............................................................................ 9
6.4 Electric shutter speed switch............................................................ 10
6.5 Partial scanning switch ..................................................................... 10
7. Operation mode ........................................................................................ 11
7.1 Internal synchronization ................................................................... 11
7.2 Internal synchronization draft mode ............................................... 11
7.3 Internal synchronization partial readout ......................................... 12
7.4 1-pulse trigger .................................................................................... 13
7.5 1-pulse trigger partial readout ......................................................... 13
7.6 Pulse width trigger ............................................................................ 14
7.7 Pulse width trigger partial readout .................................................. 14
8. Partial Scanning ........................................................................................ 15
8.1 Scanning area 1/15 (70 lines, 60 fps) ............................................... 15
8.3 Scanning area 1/2 (560 lines, 24 fps) ............................................... 15
8.2 Scanning area 1/2.6 (400 lines, 30 fps) ............................................ 15
8.4 Scanning area 2/3 (700 lines, 20 fps) ............................................... 15
9. Timing Chart .............................................................................................. 16
9-1 All pixel scanning .............................................................................. 16
9.2 Draft mode.......................................................................................... 17
9.3 Partial Scanning ................................................................................. 18
10. TROUBLESHOOTING CHART................................................................... 20
11. SPECIFICATIONS ....................................................................................... 20
12. EXTERIOR VIEW ........................................................................................ 21

5
1. CAUTIONS ON USE AND INSTALLATION
•Carefully handle the units.
Do not drop, or give a strong shock or
vibration to the camera. This may cause
problems. Treat the camera cables care-
fully to prevent cable problems, such as
cable breakdown and loosened connec-
tions.
•Do not shoot intense light.
If there is an intense light at a location
on the screen such as a spot light, a
blooming and smearing may occur.
When intense light enters, vertical stripes
may appear on the screen. This is not a
malfunction. Ghosts may occur when
there is an intense light near the object.
In this case, change the shooting angle.
•Install the camera in a location free from
noise.
Ifthecameraorthecablesarelocatednear
power utility lines or a TV, etc. undesir-
able noise may appear on the screen. In
such a case, try to change the location of
the camera or the cable wiring.
•Moire
When thin stripe patterns are shooted,
stripe patterns that are not actually there
(moire) may appears as interference
stripes. This is not a malfunction.
•Operating ambient temperature and hu-
midity.
Do not use the camera in places where
temperature and humidity exceed the
specifications. Picture quality will lower
and internal parts may be damaged.
Be particularly careful when using in
places exposed to direct sunlight. When
shooting in hot places, depending on the
conditions of the object and the camera
(for example when the gain is increased),
noise in the form of vertical strips or
white dots may occur. This is not a mal-
function.
•Handling of the protection cap.
Keep the protection cap away from chil-
dren. Children may put them into mouth
or swallow them accidentally. The pro-
tection cap protects the image sensing
plane when the lens is removed from the
camera, do not throw away.
•When not using the camera for a long-
time.
Stop supplying power.
•When cleaning the camera
Always turn off the power and clean with
a piece of dry cloth. If necessary, gently
wipe with a cloth dampened with thinned
detergent. Do not use benzine, alcohol,
thinner, etc. If used, coating and printed
letters may be discolored. When cleaning
the lens, use a lens cleaning paper, etc.
2. COMPONENTS
(1)Camera ............................................................. 1
(2)Accessories
Instruction manual.......................................... 1

6
11
11
1Picture-shooting area
The protection cap is attached on the lens mount portion. After removing the cap, mount
the lens. Be careful not to scratch or touch the optical area.
22
22
2DC IN 12V terminal
Accept a DC power input (12V).
33
33
3MODE SELECT switch
Selects the gain mode (OFF/ON).
Selects the synchronizing output signal (HD, VD/LEN, FEN).
Selects the operation mode.
Selects the electric shutter exposure time.
Selects the partial scanning mode.
44
44
4GAIN control volume
Adjusts the video signal gain when the gain mode is set to ON with the MODE SELECT
switch 33
33
3.
55
55
5DIGITAL terminal
IK-SX1L: Outputs the EIA RS-644 LVDS 8-bit digital signal. Enters a trigger signal.
IK-SX1: Outputs the Camera Link signal (8-bit digital signal). Enters a trigger signal.
3. CAMERA PARTS AND FUNCTIONS
DC IN 12V
MODE SELECT
DIGITAL
GAIN
[Front] [Rear]
DIGITAL terminal
5
GAIN control volume
4
MODE SELECT
switch
3
DC IN 12V terminal
2
Picture-shooting area
1

7
4. CONNECTIONS
4.1. Standard Connection
Lens
IK-SX1L
IK-SX1
Image processor
DC IN 12V
DC power supply
Camera cable
(option)
4.2. Cautions on Connection
• When connecting the camera cables, be sure to turn off the camera and the other
equipment connected.
• The lens for high resolution is recommended.
When using another lens, the best camera performance of this camera may not be
obtained.
(For example, low resolution may occur, and flare, ghost or shading may occur)
• For DC power supply connecting to DC IN 12V terminal, use UL listed and/or CSA
approved ungrounding type AC adaptor with the specifications described below.
Power supply voltage: DC12V±10%
Current rating: More than 830 mA, Less than 2.5A
Ripple voltage: Less than 50 mV(p–p)
Connector: HR10A–7P–4S by HIROSE electronics Co. Ltd Pins 1, 2: +12V
Pins 3, 4: GND
4.3. Connector Pin Assignments
<IK-SX1L, IK-SX1>
1
2
3
4
1
2
3
4
DC IN 12V
+12V
+12V
GND
GND
Hirose Electronics Co. Ltd. HR10A-7P-4PB

8
1
2
3
4
5
6
7
8
9
10
11
12
13
14
+D0 (Video Data (LSB))
+D1 (Video Data)
+D2 (Video Data)
+D3 (Video Data)
+D4 (Video Data)
+D5 (Video Data)
+D6 (Video Data)
+D7 (Video Data (MSB))
+VD/+FEN
+HD/+LEN
+PCK (Pixel clock)
Trigger in (Trigger input)
CC3 (Partial Scanning setting)
GND
15
16
17
18
19
20
21
22
23
24
25
26
27
28
–D0 (Video Data (LSB))
–D1 (Video Data)
–D2 (Video Data)
–D3 (Video Data)
–D4 (Video Data)
–D5 (Video Data)
–D6 (Video Data)
–D7 (Video Data (MSB))
-VD/–FEN
-HD/–LEN
–PCK (Pixel clock)
CC2 (Partial Scanning setting)
CC4 (Partial Scanning setting)
GND
<IK-SX1L>
DIGITAL
<IK-SX1>
1
2
3
4
5
6
7
8
9
10
11
12
13
GND
–X0
–X1
–X2
–Xclk
–X4
NC
NC
–CC1 (Trigger input)
+CC2 (Partial Scanning setting)
–CC3 (Partial Scanning setting)
+CC4 (Partial Scanning setting)
GND
14
15
16
17
18
19
20
21
22
23
24
25
26
GND
+X0
+X1
+X2
+Xclk
+X4
NC
NC
+CC1 (Trigger input)
–CC2 (Partial Scanning setting)
+CC3 (Partial Scanning setting)
–CC4 (Partial Scanning setting)
GND
DIGITAL
113
1426
114
1528
5. OPERATION
11
11
1Referring to the item ”4. CONNECTION”, connect each equipment correctly.
22
22
2Turn on the connected equipment and the camera.
33
33
3Pointing the lens at the object, operate the lens iris adjustment, focus adjustment, etc.
44
44
4Set the necessary mode by referring to “6. Setting”.
Hirose Electronics Co. Ltd.
HR10A-28S
3M
10226-1210

9
6. Setting
MODE SELECT switch
6.1 Gain switch
Use this switch when the image is dark even if the lens iris is fully opened. When the gain
ON is set, adjust the video signal level with the gain control volume on the rear panel.
No. 1: Gain ON/OFF
No. 2: Synchronizing signal selection
No. 3: Mode setting
No. 4: Mode setting
No. 5: Mode setting
No. 6: Electric shutter speed
No. 7: Electric shutter speed
No. 8: Electric shutter speed
No. 9: Partial scanning area
No. 10:Partial scanning area
ON
1234567890
Mode
Gain OFF
Gain ON
No.1
OFF
ON
(–3 to 12dB variable with the control volume)
Mode
HD/VD
LEN/FEN
No.2
OFF
ON
Mode
Internal synchronization
1-pulse trigger
Pulse width trigger
Internal synchronization draft mode
Internal synchronization partial scanning*
1-pulse trigger partial scanning
Pulse width trigger partial scanning
Internal synchronization partial scanning*
No.3
OFF
OFF
OFF
OFF
ON
ON
ON
ON
No.4
OFF
OFF
ON
ON
OFF
OFF
ON
ON
No.5
OFF
ON
OFF
ON
OFF
ON
OFF
ON
6.2 Synchronizing mode selector switch
This selects the DIGITAL terminal synchronizing signals output.
6.3 Mode setting switch
This sets the operation mode.
* Same mode

10
6.4 Electric shutter speed switch
This sets the electric shutter speed and the exposure time for the 1-pulse trigger.
Electric shutter speed
1/15
1/100
1/500
1/1000
1/2000
1/4000
1/10000
1/50000
No.6
OFF
OFF
OFF
OFF
ON
ON
ON
ON
No.7
OFF
OFF
ON
ON
OFF
OFF
ON
ON
No.8
OFF
ON
OFF
ON
OFF
ON
OFF
ON
Operation mode
Scanning area 1/15 (70 lines, 60 fps)
Scanning area 1/2.6 (400 lines, 30 fps)
Scanning area 1/2 (560 lines, 24 fps)
Scanning area 2/3 (700 lines, 20 fps)
No.9
OFF
OFF
ON
ON
No.0
OFF
ON
OFF
ON
Switch No. 3 on
the rear panel
OFF
OFF
OFF
OFF
OFF
DIGITAL
terminal CC2
H
H
H
H
L
DIGITAL
terminal CC3
H
H
L
L
*
DIGITAL
terminal CC4
H
L
H
L
*
*: Don’t care. (Either L or H is OK.)
6.5 Partial scanning switch
This sets the partial scanning area.
(Partial scanning can also be set from the DIGITAL terminal on the rear panel.)
Setting from the DIGITAL terminal
(No.9 and No.0 of the MODE SELECT switch become ineffective. )
Operation mode
Scanning area 1/15 (70 lines, 60 fps)
Scanning area 1/2.6 (400 lines, 30 fps)
Scanning area 1/2 (560 lines, 24 fps)
Scanning area 2/3 (700 lines, 20 fps)
Partial scanning OFF

11
7. Operation mode
7.1 Internal synchronization
Horizontal synchronization: 15.998 kHz (28.63636 MHz x 1790 clocks)
Vertical synchronization: 15 fps (14.98 Hz = 28.63636 MHz x 1790 clocks x 1068 lines)
Output signal: Video data, pixel clock, FEN/VD, LEN/HD
Video data
(video period image)
HD
VD
FEN
LEN
7.2 Internal synchronization draft mode
When the draft mode is set, the frame rate can be increased by thinning out the image
when outputting.
Horizontal synchronization: 15.998 kHz
Vertical synchronization: 60 fps
Output signal: Video data, pixel clock, FEN/VD, LEN/HD
HD
VD
FEN
LEN
Video data
(video period image)

12
7.3 Internal synchronization partial readout
When the partial scanning is set, the frame rate can be increased by decreasing the num-
ber of output lines. The number of settable output lines is 70/400/560/700 lines. For the
detail, refer to “8. Partial Scanning”.
Horizontal synchronization: 15.998 kHz (28.63636 MHz x 1790 clocks)
Output signal: Video data, pixel clock, FEN/VD, LEN/HD
Output
Output
Draft mode OFF
All pixels are independently read out. Draft mode ON Pixels are thinned out and read out.
(Only the white pixel is read out.)
HD
VD
FEN
LEN
Video data
(video period image)

13
7.4 1-pulse trigger
Exposure starts by the trigger signal input to the DIGITAL terminal, and outputs a 1-frame
image. The shutter speed (exposure period) is set with the MODE SELECT switch No. 6 -
No. 8 on the rear panel.
Input signal: Trigger
Output signal: Video data, pixel clock, FEN/VD, LEN/HD
Exposure period
Video data
(video period image)
HD
Trigger
VD
FEN
LEN
7.5 1-pulse trigger partial readout
This is the mode for partial scanning by the 1-pulse trigger operation.
Input signal: Trigger
Output signal: Video data, pixel clock, FEN/VD, LEN/HD
HD
Trigger
VD
FEN
LEN
Video data
(video period image)
Exposure period

14
7.6 Pulse width trigger
This is the mode to set the exposure period by the pulse width of the trigger signal ap-
plied to the DIGITAL terminal. This accumulates electric charge taking the trigger signal
“L” period as exposure time, and developes a 1-frame image. The trigger signal mini-
mum pulse width (“L” period) is 20µs (1/50000s).
Input signal: Trigger
Output signal: Video data, pixel clock, FEN/VD, LEN/HD
HD
Trigger
VD
FEN
LEN
Video data
(video period image)
Exposure period
7.7 Pulse width trigger partial readout
This is the mode for partial scanning by the pulse width trigger operation.
Input signal: Trigger
Output signal: Video data, pixel clock, FEN/VD, LEN/HD
HD
VD
FEN
LEN
Trigger
Video data
(video period image)
Exposure period

15
8. Partial Scanning
The set number of vertical lines is partially scanning, and the frame rate can be increased.
8.1 Scanning area 1/15
(70 lines, 60 fps)
8.2 Scanning area
1/2.6 (400 lines, 30 fps)
8.3 Scanning area 1/2
(560 lines, 24 fps)
8.4 Scanning area 2/3
(700 lines, 20 fps)
70 lines
400 lines
560 lines
700 lines

16
9. Timing Chart
9-1 All pixel scanning
1V-rate
Internal synchronization
1-pulse trigger, pulse width trigger
1068H
VD
FEN
Video output
1040H 11H
9H 8H
Video period
VD
FEN
1040H
2H
9H
Video output
Video period

17
2H-rate
1790
HD
LEN
1392
402
180
4
The digits indicate the number of clocks.
1 clock = 34.9 ns (28.63636 MHz)
Video output
Video period
9.2 Draft mode
1V-rate
267H
VD
FEN
260H
1H 1H
9H
Video output
Video period

18
2H-rate
9.3 Partial scanning
1V-rate
Internal synchronization
1790
HD
LEN
Video output
402
1392
4
180
Video period
The digits indicate the number of clocks.
1 clock = 34.9 ns (28.63636 MHz)
VD
FEN
99H
66H
50H
36H
9H
70H
400H
560H
700H
98H
65H
49H
35H
276H
540H
668H
780H
Video output
Total
Sweep-off period Sweep-off period Video period
70 lines readout
400 lines readout
560 lines readout
700 lines readout

19
1-pulse trigger, pulse width trigger
2H-rate
FEN
99H
66H
50H
36H
9H
3H
70H
400H
560H
700H
98H
65H
49H
35H
276H
540H
668H
780H
VD
(internal synchronization
output position)
VD
(output position)
Video output
Total
Sweep-off period Sweep-off period Video period
70 lines readout
400 lines readout
560 lines readout
700 lines readout
HD
LEN
Video output
Video period
The digits indicate the number of clocks.
1 clock = 34.9 ns (28.63636 MHz)
4
180
402
1392
1790

20
11. SPECIFICATIONS
10. TROUBLESHOOTING CHART
Symptoms
No image Possible causes • Is power properly supplied?
• Is the lens iris adjusted properly?
• Is the CRT monitor adjusted properly?
• Is the shutter mode set correctly?
* Design and specifications are subject to change without notice.
Power supply
Power consumption
Image sensor
(Effective pixels)
Scanning system
Scan frequency
Sensitivity
Lens mount
Ambient temperature
Ambient humidity
Weight
External dimension
Gain
Video output
Electric shutter
Mode
Partial scanning
Sync signal output
External trigger input
Optional parts
DC12 ±10%
Approx. 1.7W
2/3inch Progressive Scanning CCD
(Horizontal: 1392 pixels, Vertical: 1040 pixels)
Noninterlace
Horizontal: 15.998 kHz, Vertical: 14.98 Hz
F16 600 lx (GAIN OFF)
C mount
32 to 104°F (0 to 40°C)
Less than 90%
Approx. 4.77 oz (135g)
1.73" (W) x 1.73" (H) x 2.05" (D)
(44 (W) x 44 (H) x 52 (D) mm) (except for protruded portion)
ON (-3 to 12 dB), OFF (0 dB)
IK-SX1L: EIA RS-644 LVDS video 8-bit digital output
IK-SX1: Camera link video 8-bit digital output
1/15s, 1/100s, 1/500s, 1/1000s, 1/2000s, 1/4000s,
1/10000s, 1/50000s
Internal synchronization, internal synchronization draft,
internal synchronization partial scanning
1-Pulse trigger, 1-pulse trigger partial scanning
Pulse width trigger, Pulse width trigger partial scanning
Scanning area 1/15 (70 lines, 6 fps)
Scanning area 1/2.6 (400 lines, 30 fps)
Scanning area 1/2 (560 lines, 24 fps)
Scanning area 2/3 (700 lines, 20 fps)
HD, VD/LEN, FEN LVDS format (IK-SX1L)
Camera Link format (IK-SX1)
PCK (28.63636 MHz) LVDS format (IK-SX1L)
Camera Link format (IK-SX1)
TRIGGER; Low level: Less than 0.4V, High level: 3.4 to 5V
Negative
More than 20µs pulse width
EXC-SX03M (cable for IK-SX1L), EXC-SX03A (cable for IK-
SX1L), EXC-CL05 (cable for IK-SX1), etc.