Toshiba MK5002MPL User manual

TOSHIBA AMERICA INFORMATION SYSTEMS
STORAGE DEVICE DIVISION
IRVINE, CALIFORNIA
MK5002MPL (HDD1232)
1.8-INCH HARD DISK DRIVE
USER MANUAL
Rev 02
11/2006

CONTENTS
Introduction..............................................................................1
Setup ........................................................................................2
Using the HDD .........................................................................3
Specifications ..........................................................................4
Drive Connectors.....................................................................6

1
INTRODUCTION – MK5002MPL (HDD1232) HARD DISK DRIVE
General Features
•1.8" sized drive
•1 Platter
•5.007 Gigabytes*
•5mm High
•15ms Average Seek Time
•ATA(1 - 5) Interface
•Ultra66 Supported
•256KB Buffer
•Rotational speed of 3,990rpm
•MTTF 300,000 Hours
•68-pin ATA and PC Card ATA Interface
*Toshiba defines a megabyte (MB) as 1,000,000 bytes and a gigabyte (GB) as 1,000,000,000 bytes.

2
SETUP – MK5002MPL (HDD1232) HARD DISK DRIVE
Caution: Your Hard Disk Drive is a precision device and even a small drop onto any surface can
cause damage. Electronstatic discharge can also damage the drive. You should ground yourself
prior to handling the drive.
Figure 1. MK5002MPL Side View
Installation Notes
•Do not apply any force to the top cover, except the screw areas on top cover. Maximum force to the
specified area is 2N
•Locate PC Card Type II slot and gently slide in drive until it locks into
place.
important Note: Disconnect power from your computer system before beginning
installation

3
USING THE HARD DISK DRIVE – MK5002MPL (HDD1232)
HARD DISK DRIVE
Backing up Data Files
To avoid data loss, regularly back up the data files on the hard disk drive.

4
SPECIFICATIONS –MK5002MPL (HDD1232) HARD DISK DRIVE
General
Model MK5002MPL (HDD1232)
Interface ATA-1/2/3/4/5 (68-pin
PC Card ATA
Functionality
Formatted Capacity 5.027GB*
Rotational Speed 3,990rpm
Avg. Rotational Latency 7.52/ms
Spin-up Time 3sec (typical)
Buffer 256Kb
Seek Time
Average
Maximum
15
26
Internal Transfer Rate 93 ~ 125 Mbits/sec (max)
Host Transfer Rate
Ultra DMA mode
PIO Mode
66.7Mbytes/sec
16.6Mbytes/sec
Interleave Factor 1:1
*Toshiba defines a megabyte (MB) as 1,000,000 bytes and a gigabyte (GB) as 1,000,000,000 bytes.
Internal Drive Characteristics
Number of Disks 1
Number of Data Heads 2
Track Density (TPI) 1,638 (41.6k)
Logical Cylinders 10,390
Logical Heads 16
Logical Sectors/track 63
Bytes per Sector 512
Logical Blocks (LBA) 9,818,530
Reliability
Preventative maintenance None
Non-recoverable read errors 1 error per 1013 bits read
Electrical
Voltage 5V 5%
3.3V 5%

5
Power Consumption
3.3V 5V
Start 1.2W typ 1.9W typ
Seek 1.3W typ 2.0W typ
Read 1.2W typ 1.9W typ
Write 1.3W typ 2.0W typ
Sleep 0.5W typ 0.10W typ
Energy Consumption
Efficiency
0.10W/GB avg 0.16W/GB avg
Shock
Operating 1,960m/s2(200G)(2msec)
Non-Operating 9,800m/s2(1000G)(1msec)
Physical
Height 0.2 (5.0mm)
Width 2.13" (54.0mm)
Depth 3.37" (85.6mm)
Weight .94oz (55g) typ
Regulatory
The drive satisfies the following standards:
Underwriters Laboratories (UL) 1950
Canadian Standard Association (CSA) C22.2 No. 950
TUV Rheinland EN 60 950
EMC - EN50081-1 EN50081-1: 1992
EN55022: 1994 Class B
EN61000-3-2: 1995
EN61000-3-3: 1995
EMC - EN50082-1 EN61000-4-2: 1995
EN61000-4-3: 1998
ENV50204: 1995
EN61000-4-4: 1995
EN61000-4-5: 1995
EN61000-4-6: 1996
EN61000-4-11: 1994

6
DRIVE CONNECTORS –MK5002MPL (HDD1232) HARD DISK DRIVE
Figure 1. MK5002MPL HDD - INTERFACE CONNECTOR
Interface Connector
Drive Side Connector MCD-D50 Series by DDK Connectors
Recommended Host Side Connector MCD-D50 Series by DDK Connectors

7
Interface Signals
DRIVE INTERFACE SIGNALS
PIN SIGNAL PIN SIGNAL
1 RESET 2 GROUND
3 DD 7 4 DD 8
5 DD 6 6 DD 9
7 DD 5 8 DD 10
9 DD 4 10 DD 11
11 DD 3 12 DD 12
13 DD 2 14 DD 13
15 DD 1 16 DD 14
17 DD 0 18 DD 15
19 GROUND 20 OPEN
21 DMARQ 22 GROUND
23 DIOW/STOP 24 GROUND
25 DIOR/
-DMARDY
HSTROBE
26 GROUND
27 IORDY/
-DMARDY/-
DSTROBE
28 CSEL
29 DMACK 30 GROUND
31 INTRQ 32 IOCS16
33 DA1 34 PDIAG
35 DA0 36 DA 2
37 CS0 38 CS1
39 DASP 40 GROUND
41 3.3V (LOGIC) 42 3.3V (MOTOR)
43 GROUND 44 RESERVED
Note: Symbol () in front of signal indicates negative logic.