Toto Clean Dry HDR110#SS User manual

INSTALLATION MANUAL Clean Dry™
High Speed Concealed Hand Dryer
Important Safeguards
(For your safety, please follow the instructions below.)
Warning
Ignoring these symbols may cause
personal injury and/or property damage.
*Some models may have different components from the ones illustrated below.
Do not install the unit in the places where corrosive
or combustible gas can be present.
This may cause product failure or damage.
Do not use in
humid area
Warning
Never attempt to disassemble for repair or
modification.
This may cause electric shock, fire, injury or failure
Do not install outdoors or where it is exposed to
water.
This may cause current leakage, electric shock, fire, or failure.
Do not
disassemble
Specification
0GU3049E 2009.04
Do not
Caution
Ignoring these symbols may cause
severe injury and/or property damage.
Product HDR110#SS
Power Rating 120V AC, 4.25 Amps, 60 Hz, 510 W
Power Saving Function Automatically turns OFF after 60 seconds of use
58 dB
Ambient temperature 32° - 104°F (0° - 40°C)
Size 9-5/8" x 18-1/2" x 6-5/16"
Decibel Rating
Power Connection Hardwiring
224 mph (100 meters/second)
Air Speed
12 seconds
Dry Time
0.27 gal (950 ml)
Drain Tray Capacity
Weight 22.2 lbs (10kg)
Warning
It is necessary to install a circuit-breaker in the power supply
Failure to do this may cause electric shock during overload or short
circuit.
Important
Caution
The chassis assembly must be installed on a smooth and even
wall surface which has enough strength.
Failure to do this may cause damage or personal injury if it falls down.
Important
In this Instruction Manual, the following symbols are shown for safe and proper use of
the product and to alert you of the possibility of personal injury and damage to your
property.
The symbols and their meanings are as follows:
Warranty Registration and Inquiry
For product warranty registration, TOTO U.S.A. Inc. recommends online Warranty Registration. Please visit our web site http://www.totousa.com. If you have questions regarding warranty policy or
coverage, please contact TOTO U.S.A. Inc., Customer Service Department, 1155 Southern Road, Morrow, GA 30260 [phone] or [phone] when calling from outside of U.S.A.
HandDryerSupply.com | 804-859-2498 | [email protected]

Before Installing
1. Precautions
2. Others
Confirm the rough-in, major dimensions and wiring diagram before installation
in order to properly install the hand dryer and electrical wiring.
All electrical wiring should be installed in accordance with national/local codes
and regulations with assistance from a certified electrician.
Mounting surface should be even and smooth.
Confirmation must be made that the wall has enough strength for hand dryer
installation and be sure to use all the mounting hardware provided to securely
install the hand dryer.
It is necessary to install circuit breaker for the power supply.
Pay special attention so that both the top cover and the sensor surface are
not flawed or scratched.
Do not place other devices using inverter or infrared sensor near the
hand dryer, this may cause malfunction.
Set-up Drawing
Some models may have different components as illustrated below.
*Recommended mounting bracket heights from floor are as follow:
- Male/Female: 29-1/2”(750 mm)
- Children: 23-1/2”(598 mm)
- Handicapped: 21-1/2”(547 mm)
Meets the American Disabilities Act Guidelines, ANSI A117.1 and CSA B651 requirements
when mounted in a recessed wall where the front surface is not more than 4” (102mm) from
finished wall and max. height of air blower outlet from finished floor is 47-1/4” (1200mm).
*
FLOOR
1-9/16″ (40mm)
3-9/16″ (90mm)
2-3/8″ (60mm)
2-3/8″ (60mm)
FINISHED
WALL
OPEN WALL
1-9/16″
(40mm)
3-1/8″ (80mm)
2-3/4″ (70mm)
2-3/4″ (70mm)
1-3/16″ (30mm)
26-5/16″
(668mm)
11-13/16″
(300mm)
5-1/8″
(130mm)
1-5/16″
(34mm)
2″ (50mm)
Junction box
location
27-9/16″ - 27-5/8″ (700±2 mm)
1-9/16″
(40mm)
12-5/8″
(320mm)
28-3/4″
(730mm)
5-1/8″
(130mm)
6-7/16″
(164mm)
26-5/16″ (668mm)
9-15/16″ (252mm)
2″
(50mm)
HandDryerSupply.com | 804-859-2498 | [email protected]

Installation *Some models may have different component as illustrated below.
※
Hand Dryer Unit w/o Top Cover
Accessories Model is subject to change without further notification.
Mounting Bracket Screws and Vandal Resist Hex Wrench Template
Installation Manual
(φ4.5×30) ×6
(M4×6) ×2
Bracket (Top)
Bracket (Bottom)
Installation
position
Installation
position
Wiring Hole
Water Tray
Chassis Assy
Filter
Filter case
Top cover
Drain tray
Power Cable
<Bottom view>
Filter case
Wall surface
Sensor
Air nozzles
<View with cover removed>
Junction box
(Connection type)
Color : White,Black,Green
Size : AWG16×3
HandDryerSupply.com | 804-859-2498 | [email protected]

Installation Procedure
To be continued on the back
・
・
Attach the bracket firmly on the rigid wall with the three screws (φ4.5×30)
provided.
In the case of a tile or concrete wall, please use plastic plug anchors with
screws provided.
Mark the wall with template and install the bracket
Caution Chassis Assy. must be installed on a rigid and even surface
Failure to do this may cause damage or personal injury when it falls.
STEP 1
STEP 1
*
Recommended mounting bracket heights from floor are as follow:
- Male/Female: 29-1/2” (750 mm)
- Children: 23-1/2” (598 mm)
- Handicapped: 21-1/2” (547 mm)
1-9/16″
(40mm)
Finished
wall
Finished
wall
1-9/16″
(40mm)
3-1/8″
(80mm) 2-3/4″
(70mm)
2-3/4″
(70mm)
Bracket (Bottom)
Beam/Stud
1-9/16″ (40mm)
Wall
Finished Wall
Remove drain tray
during installation
△
Junction box
location
Drain tray
Wall thickness needs
to be 5 to 30mm.
Wall thickness needs
to be 5 to 30mm.
Bracket
(Top)
Beam/Stud
1Using template provided, mark the wall for locations and install
the mounting bracket.
2Complete the electrical wiring; install the junction
box, and connect the power cord using wire nuts.
3Mount the chassis assembly and drain tray assembly
4Install the top cover and drain tray
1-9/16″ (40mm)
1-9/16″
(40mm)
3-1/8″ (80mm)
2-3/4″ (70mm)
2-3/4″ (70mm) 1-3/16″ (30mm)
1-3/16″ (30mm)
2″ (50mm)
2″ (50mm)
3-9/16″ (90mm)
2-3/8″ (60mm)
2-3/8″ (60mm)
3-9/16″ (90mm)
2-3/8″ (60mm)
2-3/8″ (60mm)
HandDryerSupply.com | 804-859-2498 | [email protected]

STEP 2 －
STEP 3
STEP 2 Complete the electrical wiring STEP 3 Mount the Chassis Assembly and Drain Tray
Assembly
※
Connection
Diagram
Connect the cord firmly with a wire nut or equivalent.
・
・
Make sure all electrical wiring is placed away inside the junction box.
Use 2 screws (M4) that come with the product and tighten unit to the bottom
bracket.
・Place chassis assembly onto the bottom bracket.
・Using wire nuts, connect power cable from hand dryer to power supply in the
junction box (confirm with certified electrician on correct wire nuts to use).
・Place connection point (with wire nuts) into the junction box.
・Hang chassis assembly onto the top bracket.
Connection point
(Actual Placement)
Junction box
Place mounting platform
onto mounting bracket hooks.
Place connection point (with
wire nuts) into the junction box
(Actual Placement)
Junction box
Chassis
Assy
Bracket (Top)
Bracket (Bottom)
Attach water tray after
installation is complete
Screw in two screws onto bottom
of body through the bottom bracket
(Actual Placement)
Junction box
Chassis Assembly
Drain tray
HandDryerSupply.com | 804-859-2498 | [email protected]

■
■
・
・
1.
・
2.
・
After trial run
Test the product as follows after the installation is complete.
Check the circuit breaker
Check the functionality
Turn the circuit breaker ON.
Place your hand under the outlet nozzles to see if air blows out.
After you check the functionality by trial run, give the user manual
(with warranty) to the customer, and explain how to use and maintain the
product.
First peel off the seal on the filter.
(The seal is used to protect the filter from scratches during
shipment; it is no longer needed.)
B=BLACK
R=RED
W=WHITE
Bu=BLUE
G=GREEN
Sensor
Control
Assembly
Motor
Power
Connector Power Fuse
Motor
G
B
W
WB
WW
P1-1 P1-2 P3
P2
P7
P6
15A
GBody Case
Function Test
1. Checking after installation Wiring Diagram
Peel off the seal
Air nozzles
HandDryerSupply.com | 804-859-2498 | [email protected]