Toto Connelly TS221T Installation instructions

Warranty Registration and Inquiry
For product warranty registration, TOTO U.S.A. Inc. recommends online warranty registration. Please visit
our web site http://www.totousa.com. If you have questions regarding warranty policy or coverage, please con-
tact TOTO U.S.A. Inc., Customer Service Department, 1155 Southern Road, Morrow, GA 30260
[phone] or [phone] when calling from outside of U.S.A.
Installation and Owner’s Manual
Manual de Instrucciones y del Propietario
Manuel d’Installation et d’Utilisation
½” Thermostatic Trim
½” Acabado De Termostática
½” Garniture De Thermostatique
Connelly™
TS221T

2
ENGLISH
TABLE OF CONTENTS
THANKS FOR CHOOSING TOTO!
The mission of TOTO is to provide the world with healthy, hygienic and more
comfortable lifestyles. We design every product with the balance of form and
function as a guiding principle. Congratulations on your choice.
Thanks for Choosing TOTO!..............................................................................2
Before Installation ...............................................................................................2
Common Tools Needed .....................................................................................2
Included Parts......................................................................................................3
Care & Cleaning ..................................................................................................3
Installation Procedure ......................................................................................4-6
Warranty...............................................................................................................7
Rough-In Dimensions .......................................................................................20
BEFORE INSTALLATION
Observe all local plumbing codes.
Make sure the water supply is shut off.
Read these instructions carefully to ensure proper installation.
TOTO reserves the right to update the product design without notice.
COMMON TOOLS NEEDED
Adjustable
Wrench Hacksaw
10°
70°
120°
Thermometer

3
ENGLISH
INCLUDED PARTS
Escutcheon * Sleeve Handle Assembly *
Temperature Limit Stop Set Screw & Hex Wrench Valve with Plaster Guard
TSST
* Actual product may vary in appearance depending on the model.
TS221T shown.
Check to make sure that all these parts were included in your packaging:
REQUIRED - NOT
INCLUDED
CARE & CLEANING
Your new shower trim is designed for years of trouble-free performance. Keep
it looking new by cleaning it periodically with mild soap, rinsing thoroughly
with warm water and drying with a clean, soft cloth. Do not use abrasive
cleaners, steel wool or harsh chemicals, as these will dull the finish. Failure to
follow these instructions may void your warranty.
INSTALLATION PROCEDURE
1. Confirm that the valve has
been installed properly.
NOTE: The finished wall
surface should be between the
min and max markings on the
plaster guard. See the TSST
installation manual for further
information.
Plaster Guard
Thermostatic
Valve
Finished Wall
Max 95mm (3-3/4”)
Min 65mm (2-1/2”)

4
ENGLISH
3. Measure the distance from the finished wall
to the top of the trim adapter. Compare that
distance with the table below to determine
which stop to use:
4. Remove the trim adapter.
Install the proper length
temperature limit stop,
making sure that the
alignment marks on the
valve body and limiter line
up (roughly at 1 o’clock
position).
Reinstall the trim adapter.
X Use
Less than
2-1/16”
(53mm)
Long Temperature
Limit Stop
1.5” (37.5mm) *
2-1/16”
(53mm)
or more
Short Temperature
Limit Stop
1” (25mm)
Trim Adapter
Finished Wall
(X)
Alignment
Mark on Stop Alignment
Mark on Valve
Installation Procedure (continued)
* Pre-installed on valve
Trim Adapter
Long Stop
Short Stop
2. Remove the plaster guard from
the valve.
Plaster Guard
Valve

5
ENGLISH
5. Hold the faceplate on the wall,
centered around the trim adapter,
with the “104F” markings at the top.
Screw the escutcheon onto the trim
adapter and tighten it against the
faceplate.
6. Push the handle assembly fully
onto the valve stem. Measure the
distance “X” between the handle
and flat on the escutcheon.
Compare that measurement to
the following table to determine
where to cut the valve stem. Cut
the valve stem and be sure to
clean any burrs with a file.
A
B
X Cut Stem
More than 1”
(26mm) D
1” (25mm)
to 7/8” (21mm) C
7/8” (20mm)
to 5/8” (16mm) B
5/8” (15mm)
to 3/8” (11mm) A
Less than 3/8”
(10 mm) Do not cut
Installation Procedure (continued)
C
D
Escutcheon
Sleeve
X