Toto EGO II User manual

S06435-1MZ
"EGO II" LEVER HANDLE FLOOR STANDING BATH
& SHOWER SET
SPECIFICATIONS
OPERATING CONDITIONS
MAINTENANCE
3. CERAMIC
HEAD WORK
2. AERATOR
* Redhandlefor left side andblue handle for right side. Tighten by hand
Handle Set *
40
Ø72.5
54+8
0
258
120
8250
-8
630.5 194.5
150
45
55
Ø80
G½
18
Ø8
TROUBLESHOOTING
CHECK
POINT
Unsatisfactory spray 1 Clean
Flow rate unsatisfactory 2 Remove and clean
Water leaks around the handle 3 Tighten
PROBLEM
SOLUTION
ATTENTION
Flow Regulator Inside
(Don t remove)
R7
TX445SELMV3Z
1. NOZZLES
6
5
43
INSTALLATION
1
Make sure the floor is flat
* Removethe coverafter the
mortar has dry
2
8
7Packing
Body
Ring
* Cover
Mortar
Maximum
Mortar
Minimum
Mortar
Nut
Flexible
Hose
Cover
Pipe
Base
Drill
Hot Water
Supply *
Sleeve
Anchor
6 - Hole 8
Base
Cold W ater
Supply *
Screw
Hanger
* Pipe supplied by owner
Flexible Hose
w/ Packing
Shower
Rain Spray
Button
Massage
Spray
Button
Pipe
* Turn the nut
Nut*
1. Watersupply pressure : 0.05 ~0.75 MPa.
2. Ensure that water supply is clean ( NoSand, Dirt, Etc.).
All Finishes : Clean the finish with mild soap and warm water.
Wipe entire surface completely dry with clean soft cloth. Many
cleaners may contain chemicals, such as ammonia, chlorine,
toilet cleaner etc. which could adversely affect the finish and
are not recommended for cleaning
Handle reinstallation
1.
2.
4.
Don t use abrasive cleaners orsolvents on faucets and fittings.
FlowRegulator should not be remove because it could damage the
system
As the product model is constantly updated, the actual product may
not look the same as it shownin the diagram, but the basic
installation principles are the same.
The hot water supply side of the faucets is ina condition of high
temperature.Do not allow skin to contact with the hardwaresurface
directly. Otherwise, scalding mayoccur.
2.
1.
3.

S06435-1MZ
"EGO II" LEVER HANDLE FLOOR STANDING BATH
& SHOWER SET
SPESIFIKASI
KONDISI OPERASIONAL
PEMELIHARAAN
3. CERAMIC
HEAD WORK
2. AERATOR
* Handle merah untuk posisi kiri andhandle biru untuk posisi kanan.
Kencangkan dengan tangan
Handle Set *
40
Ø72.5
54+8
0
258
120
8250
-8
630.5 194.5
150
45
55
Ø80
G½
18
Ø8
PENYELESAIAN MASALAH
PERHATIAN
R7
TX445SELMV3Z
1. NOZZLES
6
5
43
PEMASANGAN
1
Pastikan lantainya rata
* Lepas cover setelah
mortar mengering
2
8
7Packing
Body
Ring
* Cover
Mortar
Maximum
Mortar
Minimum
Mortar
Nut
Flexible
Hose
Cover
Pipe
Base
Drill
Hot Water
Supply *
Sleeve
Anchor
6 - Hole 8
Base
Cold W ater
Supply *
Screw
Hanger
* Pipa disediakan olehpemilik
Flexible Hose
w/ Packing
Shower
Rain Spray
Button
Massage
Spray
Button
Pipe
* Putar nut
Nut*
Seluruh lapisan: Bersihkan lapisan akhir dengan sabun lembut
dan air hangat. Lap seluruh permukaan hingga benar-benar
kering dengan kain lembut yang bersih. Kebanyakanbahan
pembersih mungkin mengandung bahan kimia, seperti amonia,
klorin, pembersih toilet, dll. yang dapat mempengaruhi hasil akhir
dan tidak disarankanuntuk dibersihkan
Handle reinstallation
1.
2.
Pancaran tidak memuaskan 1 Bersihkan
Laju aliran tidak memuaskan 2 Lepas dan bersihkan
Air bocor disekitar handle 3 Kencangkan
MASALAH
SOLUSI
POIN
PERIKSA
1. Tekanan sumber air: 0.05 ~ 0.75 MPa.
2. Pastikan kondisi sumberair adalah bersih (tidak ada pasir,
kotoran dan lain lain)
Flow Regulator Di dalam
(Jangan dilepas)
4.
Jangan gunakan pembersih atau pelarut abrasif pada faucet dan
fitting.
FlowRegulator tidak boleh dilepas karena dapat merusak sistem
Karena model produk terus mengalami pembaharuan, aktual
produk mungkin tidak samadengan gambar, tapi prinsip dasar
pemasangan adalah sama.
Sisi pasokanair panas pada kran faucet berada dalam kondisi suhu
tinggi. Jangan biarkan kulit menyentuh permukaan benda secara
langsung. Kalautidak, bisaterjadi kepanasan.
2.
1.
3.