Toto CURIO User manual

"CURIO" COMBINATION SHOWER SET TX416SC
2. CERAMIC
HEAD WORK
TX416SC
"CURIO" Cross Handle Combination Shower Set 3. BOLT
65±5
120±5
150±10
G½
Ø72.5
TX416SCL
"CURIO" Lever Handle Combination Shower Set
TX416SCS
"CURIO" Simple Cross Handle Combination Shower Set
Flow Regulator Inside
(Don t remove)
1. NOZZLES
OPTIONAL HANDLE
Packing
Hand Shower
Packing Flexible
Hose
3
CHECK
POINT
1
Unsatisfactory spray Clean
PROBLEM SOLUTION
2
Handle is loose Tighten
Tighten
Water leaks around the handle
Cover
Packing
Body
1. Water supply pressure : 0.05 ~ 0.75 MPa.
2. Ensure that water supply is clean ( No Sand, Dirt, Etc.).
1
2
SPECIFICATIONS
R5
INSTALLATION TROUBLESHOOTING
OPERATING CONDITIONS ATTENTION
3*Tigthen the nut by wrench.
Nut *
MAINTENANCE
MOUNTCONNECTORS PARALLEL WITH THE WALL
Hot
Water
Supply Cold
Water
Supply
Leg
150
150±10
Use Seal tape
(Not Include)
All Finishes : Clean the finish with mild soap and warm water.
Wipe entire surface completely dry with clean soft cloth. Many
cleaners may contain chemicals, such as ammonia, chlorine,
toilet cleaner etc. which could adversely affect the finish and
are not recommended for cleaning
Don t use abrasive cleaners or solvents on faucets and
fittings.
Flow Regulator should not be remove because it could
damage the system
As the product model is constantly updated, the actual
product may not look the same as it shown in the
diagram, but the basic installation principles are the same.
The hot water supply side of the faucets is in a condition
of high temperature. Do not allow skin to contact with the
hardware surface directly. Otherwise,
scalding may occur.
1.
2.
3.
4.
S06071S
32

"CURIO" COMBINATION SHOWER SET TX416SC
2. CERAMIC
HEAD WORK
TX416SC
"CURIO" Cross Handle Combination Shower Set
3. BOLT
65±5
120±5
150±10
G½
Ø72.5
TX416SCL
"CURIO" Lever Handle Combination Shower Set
TX416SCS
"CURIO" Simple Cross Handle Combination Shower Set
1. NOZZLES
OPSIONAL HANDLE
Packing
Hand Shower
Packing Flexible
Hose
Cover
Packing
Body
2
R5
3
Nut *
S06071S
32
Flow Regulator didalam
(Jangan dilepas)
1
SPESIFIKASI PEMASANGAN PENYELESAIAN MASALAH
KONDISI OPERASIONAL PERHATIAN
*Kencangkan nut dengan wrench.
PEMELIHARAAN
PEMASANGAN KONEKTOR SEJAJAR DENGAN
DINDING
1. Tekanan sumber air: 0.05 ~ 0.75 MPa.
2. Pastikan kondisi sumber air adalah bersih
(tidak ada pasir, kotoran dan lain lain)
Sumber
Air Panas Sumber
Air Dingin
Leg Gunakan Seal
Tape (Tidak
disertakan)
150
150±10
Seluruh lapisan : Bersihkan lapisan akhir dengan sabun lembut
dan air hangat. Lap seluruh permukaan hingga benar-benar
kering dengan kain lembut yang bersih. Kebanyakan bahan
pembersih mungkin mengandung bahan kimia, seperti amonia,
klorin, pembersih toilet, dll. yang dapat mempengaruhi hasil
akhir dan tidak disarankan untuk membersihkan
Jangan gunakan pembersih atau pelarut abrasif pada
faucet dan fitting.
Flow Regulator tidak boleh dilepas karena dapat merusak
sistem
Karena model produk terus mengalami pembaharuan,
aktual produk mungkin tidak sama dengan gambar, tapi
prinsip dasar pemasangan adalah sama.
Sisi pasokan air panas pada kran faucet berada dalam
kondisi suhu tinggi. Jangan biarkan kulit menyentuh
permukaan benda secara langsung. Kalau tidak, bisa
terjadi kepanasan.
1.
2.
3.
4.
Kencangkan
3
POIN
PERIKSA
1
Pancaran tidak memuaskan Bersihkan
MASALAH SOLUSI
2
Handle longgar Kencangkan
Air bocor disekitar handle