Toto Standard EcoPower TEL5GSC User manual

TM
TM
INSTALLATION MANUAL AUTOMATIC FAUCET
Thermal mixing valve faucet
Important Safeguards
(For your safety, please follow the instructions below.)
In this Instruction Manual, the following symbols are shown for safe and proper use
of your automatic faucet and in order to alert you to the possibility of personal injury
and damage to your property.
The symbols and their meanings are as follows.
Warning Ignoring these symbols may cause
personal injury and/or property damage.
*Some models may have different components from the ones illustrated below.
Do not place the Automatic Faucet in a high humidity
area such as shower room or sauna.
This may cause damage.
Do not use in
humid area
Warning
Do not strike or kick the Automatic Faucet.
This may cause damage or water leakage.
Never attempt to disassemble, reassemble, repair
or modify the Automatic Faucet , unless you are an
electrician, or qualified service person.
This may cause property damage or personal injury.
Do not
disassemble
Do not strike
Specification
OGU3009E 2006.4
EcoPower type Battery type
Model
number
Standard
Gooseneck
Power supply
-
-
Alkaline type AA batteries
1.5V 2pcs.
Battery life
Item
2 yrs. Life based on 4,000
cycles per month
Detection range
from the sensor
5-1/8"~7-7/8" (130~200 mm)
sensor is self-adjusting
Water supply
pressure
minimum required water pressure:
13 PSI (90 kPa) ( Flowing)
maximum water pressure:125 PSI (862 kPa)
check local building codes for maximum water
pressure allowed
Water supply connection
1/2" NPSM
TEL5GSC TEL3DSC
TEL5GGC TEL3DGC
Helix
TEL5GCCN -
Fordham TEL5GTCN
-
Axiom TEL5GKCN
-
Ambient temperature 32~104oF(0~40oC)
Humidity Max. 90% RH
Flow rate 1.06 gallon per minutes (4 L/min.)
Duration of
water discharge
Discharge quantity Max. 0.25 gallon per cycle (0.95 L/cycle) for
10 seconds type
10 seconds ( TEL5 N -10)
60 seconds (TEL5 N -60)
TM

Before Installing
1. Check the pressure of cold and hot water supply
2. Check the temperature of hot-water supply
3. Piping
4. Others
Make sure the cold water supply pressure is higher or equal to the hot water
supply pressure.
When the water supply pressure is higher than 125PSI (862kPa), be sure to
reduce the pressure within a range of 20 to 80 PSI by using a pressure
reducing valve available in the market.
Optimum working pressure range is from 7PSI to 125PSI (60kPa to 862kPa).
Make sure the water pressure is within this range.
Never use steam as a hot-water supply.
Make sure the temperature range of hot-water supply is within 140 to
185oF(60 to 85oC).
This is not mandatory for the lower limit but is recommended.
The Automatic Faucet does not discharge hot water exceeding 122oF(50oC).
Flush all water lines prior to installation.
Pay special attention so that the sensor surface is not awed or scratched.
Prepare stop valve and exible hose or copper tube.
Do not place other devices using inverter or infrared sensor near the
Automatic Faucet, this may cause malfunction.
There is no problem with the Automatic Faucet if the water remains inside.
Set-up Drawing
Some models may have dierent components as illustrated below.
Battery type
1"
(25mm)
1"
(25mm)
1-2/3"
(42mm)
3-3/4"
(95mm)
1-1/2"
(38mm)
8"(203mm)
6"
(152mm)
6-1/2"
(165mm)
10-1/4"
(260mm)34"
(864mm)
17-1/8"
(436mm)
16-7/8"
(428mm)
HOT
COLD
F.L.
1"
(25mm)
1"
(25mm)
1-2/3"
(42mm)
3-3/4"
(95mm)
1-1/2"
(38mm)
8"(203mm)
6"
(152mm)
6-1/2"
(165mm)
10-1/4"
(260mm)
34"
(864mm)
17-1/8"
(436mm)
16-7/8"
(428mm)
HOT
COLD
F.L.
EcoPowertype

H
C
H
C
Installation
*Some models may have dierent component as illustrated below. Optional Accessories (Not included)
Adjustable wrench, phillips and at head screwdrivers
Battery typeEcoPowertype
Control box Water inlet bracket Plate
4" Plate (TN71V100R) 8" Plate (71244T8CC)
Nut
Lock
washer
Washer
4" Plate
Packing
8" Plate
Base
plate
Packing
Washer
Wing nut
Tie bolt
Packing
O-ring
Installation
manual Instruction
manual
Alkaline AA
Battery(×2)
Battery case
Others
Screw
(φ3 mm×10)
Allen wrench
Size:1/16"(2mm)
Battery type
*Spout , Flexible tube and Open-close tool are included.
Gooseneck Helix FordhamAxiomStandard
Spout Flexible tube
Open-close tool
Others
※Flexible tube is installed
through spout connecting
hose.
Required Tools
Water inlet bracket (×2)
Self tapping screw (×8)
(φ4.5 mm×38)
EcoPowertype

H
C
Installation Procedure STEP 1 －STEP 3-A
5Mount the spout
9Fasten the spout with tool
Not included
1Water supply
pipe
8Attach the connector
to the controller
3Mount the two water inlet
brackets on the wall
4Connect the controller
to the water inlet brackets
2Remove the controller cover
10
Attach the controller cover
6Cut the spout
connecting hose
if necessary
7Connect the spout
connecting hose
to the controller
STEP 1Water supply pipe
Before installing the faucet, be sure to thoroughly ush away any foreign matter
such as dirt and sand trapped in the water supply pipe.
STEP 2Remove the controller cover
①Loosen the two screws on the front
cover.
②Remove the controller cover
to the direction as shown in the gure.
controller cover
screws
Pull
STEP 3-A Mount the two water inlet brackets on the wall
①Mount the water inlet brackets on the
wall and temporarily tighten the screws.
The distance between the water inlet
brackets shall be 3-3/4"( 95mm ).
The controller and the two brackets
should be temporarily connected rst
in order to ax.
To be continued on the back
Be sure to mount each water
inlet bracket in the correct
direction.
Otherwise, the strainer on the
water inlet bracket will be
in accessible for cleaning.
Caution
Wall anchors
(not included)
Water inlet
bracket
Self tapping
screw
COLD IN
OUT
HOT IN
OUT
3-3/4"
(95mm)
Note: It is required to keep a distance
of 3-3/4" between the two water
inlet brackets.
This distance is xed because
the controller attaches to these
brackets.
②Make sure that the controller can be
attached to the water inlet brackets.
③Tighten the water inlet brackets with
the eight self tapping screws.
Note: Anchors for the wall may be needed.

STEP 3-B －STEP 6
STEP 3-B Mount the two water inlet brackets on the wall
Note: Remove all protective covers.
④Connect the hot/cold water supply lines to the water inlet brackets.
Flexible hose Copper tube
Note: Make sure hot goes on the left side.
Flexible hose
Copper tube
Nut
Nut
Packing
Friction ring
Cone washer
not included
not included
STEP 4Connect the controller to the water inlet brackets
Note: Remove all protective covers.
After placing packing, attach the
controller to the water inlet brackets,
and then ax them with the nuts as
shown in the gure.
※Packing is located on the water
inlet bracket.
Packing
Water inlet bracket
Nut
Controller
STEP 5Mount the spout
①Remove the exible tube from the
spout connecting hose.
②Mount the cover plate (optional).
③Place the spout into the wash
basin hole.
④Hand-tighten the washer with the
hexagonal nut.
Caution
Spout
Washer
Hexagonal nut
Wash basin
Cord
Spout connecting
hose
Plate (optional)
STEP 6Cut the spout connecting hose if necessary
①Cut the spout connecting hose to
the appropriate length.
※If the spout connecting hose is
too long, cut it to proper length.
Do not cut the hose more than
4 inches.
Be sure to cut the hose carefully
with a cutter, so the surface
is square.
②Insert the spout connecting hose
into the exible tube.
Clean the hose
end after cutting. Spout connecting
hose
Spout connecting
hose
Flexible tube
Cutting length:
4 inches or less
90゜
Pay special attention to avoid
entangling the spout connecting
hose and cord with each other.