Toto REI S TX496SRSN User manual

SPECIFICATIONS
OPERATING CONDITIONS
S060135N
MAINTENANCE
TROUBLESHOOTING
INSTALLATION
"REI S" 3 HOLES BATH & SHOWER SET TX496SRSN
1
23
5
4
6
2. CONNECTING
NUT
Ø35 Hole
Ø32 Hole
Ø40 Hole
Flexible Hose
Packing
Packing
Shower
Holder
Flexible Hose
Shower
Nut
Packing
Packing
Lock Nut
Packing
Body
Lock Nut Wavy
Washer
Connector
Nut
120 120
210
122
255
4°
max.30
Ø50 Ø50 Ø50
G½
121
171
27°
182
c
H
Always wipe chrome plated area with dry soft cloth,
and sometimes wipe it with cloth soaked in mild soap.
Packing
3. BOLT
c
H
C
L
I
CK
Packing
R8
Hose Spring
Stopper
ToCold
Water Supply
ToHot
Water Supply
ATTENTION
Flow Regulator Inside
(Don t remove)
1. NOZZLES
CHECK
POINT
Unsatisfactory spray 1 Clean
Water leaks around the handle 2 Tighten
Handle is loose 3 Tighten
PROBLEM
SOLUTION
1. Water supply pressure : 0.05 ~ 0.75 MPa.
2. Ensure that water supply is clean ( No Sand, Dirt, Etc. )
Shower Holder
Ø40
Hole
Body
Spout
Ø35
Hole
Ø32 Hole
Don t use abrasive cleaning material such as;
detergents containing hydrochloric acids, thinner,
polishing powder, and nylon brush.
Flow Regulator should not be remove because it
could damage the system
As the product model is constantly updated, the
actual product may not look the same as it
shown in the diagram, but the basic installation
principles are the same.
1.
2.
3.

SPESIFIKASI
S060135N
PEMASANGAN
"REI S" 3 HOLES BATH & SHOWER SET TX496SRSN
1
23
5
4
6
2. CONNECTING
NUT
Ø35 Hole
Ø32 Hole
Ø40 Hole
Flexible Hose
Packing
Packing
Shower
Holder
Flexible Hose
Shower
Nut
Packing
Packing
Lock Nut
Packing
Body
Lock Nut Wavy
Washer
Connector
Nut
120 120
210
122
255
4°
max.30
Ø50 Ø50 Ø50
G½
121
171
27°
182
c
H
Packing
c
H
C
L
I
CK
Packing
R8
Hose Spring
Stopper
ToCold
Water Supply
ToHot
Water Supply
Flow Regulator Inside
(Don t remove)
1. NOZZLES
Shower Holder
Ø40
Hole
Body
Spout
Ø35
Hole
Ø32 Hole
KONDISI OPERASI
PEMELIHARAAN
Selalu bersihkan area berlapis krom dengan kain
lembut kering, dan sesekali bersihkan dengan kain
yang direndam dalam sabun yang dicampur air.
PENYELESAIAN MASALAH
PERHATIAN
1. Tekanan sumber air: 0.05 ~ 0.75 MPa.
2. Pastikan kondisi sumber air adalah bersih
(tidak ada pasir, kotoran dan lain lain)
3.
Jangan gunakan bahan pembersih yang bersifat
abrasif seperti deterjen yang mengandung asam
klorida, tinner, bubuk polishing dan sikat nilon.
Flow Regulator tidak boleh dilepas karena dapat
merusak sistem
Karena model produk terus mengalami
pembaharuan, aktual produk mungkin tidak sama
dengan gambar, tapi prinsip dasar pemasangan
adalah sama.
1.
2.
POIN
PERIKSA
Semprotan tidak memuaskan 1 Bersihkan
Air bocor disekitar handle 2 Kencangkan
Handle longgar 3 Kencangkan
MASALAH
SOLUSI
3. BOLT