Toto UMI TX492SUN User manual

4
2
Drill 2 x Ø8
Holes
"UMI" SINGLE LEVER SHOWER COLUMN SET TX492SUN
20
85
47
620
-7
918
Ø65 Ø8
40
WALL
131
949
20°
Ø180 229
150±10
G½
Use Seal Tape
(Not Include)
3
Pipe
Pipe
2. CONNECTING
NUT
4. BOLT
5
Body
Hanger
Holder
Bolt
Hex.
Key
Flow Regulator Inside
(Don t remove)
7
6
Packing
Packing
Flexible Hose
Hand Shower
Body
Packing
Cover
Nut*
Packing
Shower
Head
3. NUT
PROBLEM CHECK
POINT SOLUTION
Water leaks around the nut
Clean
Tighten
1
2
Handle is loose
Unsatisfactory spray
Tighten
3
Water leaks around the handle Tighten
4
Flow Regulator Inside
(Don t remove)
*Tighten the Nut.
1MOUNT CONNECTORS
PARALLEL WITH THE WALL
Screw
1. NOZZLES
Watersupply pressure : 0.05 ~ 0.75 MPa
Ensure that water supply is clean( No Sand,Dirt, Etc.).
1.
2.
Use Seal tape
(Not Include)
SPECIFICATIONS
S060445N R6
INSTALLATION TROUBLESHOOTING
OPERATING CONDITIONS ATTENTION
MAINTENANCE
All Finishes: Clean the finish with mild soapand warm water. Wipe
entire surface completely dry with clean soft cloth. Manycleaners
maycontainchemicals, such as ammonia, chlorine, toilet cleaner etc.
which could adversely affect the finish and are not recommended for
cleaning
150
150±10
Hot
Water
Supply
Cold
Water
Supply
Leg
Sleeve Anchor
Bracket
w/ Oring
Cover
Don t use abrasive cleaners orsolventson faucetsand fittings.
FlowRegulator should not be remove because it could damage
the system
As the product model is constantly updated, the actual product
maynot look the same as it shown in the diagram, but the basic
installation principles are the same.
The hot watersupply side of the faucets is ina condition of high
temperature.Do not allow skin to contact with the hardware
surface directly. Otherwise,
scalding may occur.
1.
2.
3.
4.

4
2
Drill 2 x Ø8
Holes
"UMI" SINGLE LEVER SHOWER COLUMN SET TX492SUN
20
85
47
620
-7
918
Ø65 Ø8
40
WALL
131
949
20°
Ø180 229
150±10
G½
Gunakan Seal tape
(Tidak disertakan)
3
Pipe
Pipe
2. CONNECTING
NUT
4. BOLT
5
Body
Hanger
Holder
Bolt
Hex.
Key
7
6
Packing
Packing
Flexible Hose
Hand Shower
Body
Packing
Cover
Nut*
Packing
Shower
Head
3. NUT
*Kencangkan nut.
1
Screw
1. NOZZLES
Gunakan Seal tape
(Tidak disertakan)
S060445N R6
150
150±10
Hot
Water
Supply
Cold
Water
Supply
Leg
Sleeve Anchor
Bracket
w/ Oring
Cover
SPESIFIKASI
KONDISI OPERASIONAL
1. Tekanan sumber air: 0.05 ~ 0.75 MPa.
2. Pastikan kondisi sumber air adalah bersih
(tidak ada pasir, kotoran dan lain lain)
PEMELIHARAAN
Seluruh lapisan : Bersihkan lapisan akhir dengan sabun lembut
dan air hangat. Lap seluruh permukaan hingga benar-benar
kering dengan kain lembut yang bersih. Kebanyakan bahan
pembersih mungkin mengandung bahan kimia, seperti amonia,
klorin, pembersih toilet, dll. yang dapat mempengaruhi hasil
akhir dan tidak disarankan untuk dibersihkan
PERHATIAN
Jangan gunakan pembersih atau pelarut abrasif pada faucet dan
fitting.
FlowRegulator tidak boleh dilepas karena dapat merusak sistem
Karena model produk terus mengalami pembaharuan, aktual
produk mungkin tidak samadengan gambar, tapi prinsip dasar
pemasangan adalah sama.
Sisi pasokanair panaspada kran faucet berada dalam kondisi
suhu tinggi. Janganbiarkankulit menyentuh permukaanbenda
secara langsung. Kalautidak, bisaterjadi kepanasan.
1.
2.
3.
4.
PEMASANGAN
PEMASANGAN KONEKTOR
SEJAJAR DENGAN DINDING
Flow Regulator
didalam
(Jangan dilepas)
Flow Regulator didalam
(Jangan dilepas)
MASALAH POIN
PERIKSA SOLUSI
Air bocor disekitar nut
Bersihkan
Kencangkan
1
2
Handle longgar
Pacaran tidak memuaskan
Kencangkan
3
Air bocor disekitar handle Kencangkan
4
PENYELESAIAN MASALAH