Toto TLP01701U Installation instructions

TOTO U.S.A., Inc. 1155 Southern Road,
Morrow, Georgia 30260
Tel: [phone] Fax: [phone]
www.totousa.com
0GU4270
Rev A
Warranty Registration and Inquiry
For product warranty registration, TOTO U.S.A. Inc. recommends online warranty registration. Please visit
our web site http://www.totousa.com. If you have questions regarding warranty policy or coverage, please con-
tact TOTO U.S.A. Inc., Customer Service Department, 1155 Southern Road, Morrow, GA 30260
[phone] or [phone] when calling from outside of U.S.A.
Warranty Registration and Inquiry
For product warranty registration, TOTO U.S.A. Inc. recommends online warranty registration. Please visit
our web site http://www.totousa.com. If you have questions regarding warranty policy or coverage, please con-
tact TOTO U.S.A. Inc., Customer Service Department, 1155 Southern Road, Morrow, GA 30260
[phone] or [phone] when calling from outside of U.S.A.
Installation and Owner’s Manual
Manual de instalación y del propietario
Manuel d’installation et d’utilisation
Manual de Instalação e do Proprietário
ZN Autofaucet
ZN Grifo Automático
ZN Robinet Automatique
ZN Torneira Automática
TLP01701U
TLP01702U

2
ENGLISH
THANK YOU FOR CHOOSING TOTO!
The mission of TOTO is to provide the world with healthy, hygienic and more
comfortable lifestyles. We design every product with the balance of form and
function as a guiding principle. Congratulations on your choice.
How to Use.........................................9
Mode Adjustment..............................9
Care and Cleaning............................11
Maintenance......................................12
Troubleshooting................................14
Warranty.............................................15
Rough-In Dimensions........................58
Thanks for Choosing TOTO!...............2
Warnings...............................................2
Before Installation................................3
Included Parts.......................................4
Tools You Will Need.............................4
Specifications........................................4
Installation Procedure..........................5
Testing and Calibration........................8
TABLE OF CONTENTS
PLEASE READ THESE IMPORTANT SAFEGUARDS FOR YOUR PERSONAL
SAFETY AND TO PREVENT DAMAGE TO PRODUCT AND PROPERTY.
⚠To ensure the product installation is completed correctly, please carefully read
this manual entirely before beginning installation.
⚠Comply with all instructions proceeded by the caution symbol (⚠) or notice
label (NOTICE) to avoid potential dangers such as injury or death, electrical
shock, property damage, or invalidation of warranty.
⚠Comply with all local plumbing codes.
⚠ Make sure the water supply is shut off before beginning installation.
⚠Never disassemble, repair or modify the product in any way not described by
this manual. Refer the product to a service engineer, if needed.
⚠Do not block the flow of water at the spout opening during use.
⚠Mount the outlet in a location higher than 100 mm from the floor. Select the
outlet mounting location so that condensation on the water supply pipe and
water splashed during use of the product does not contact the outlet, or
consider using a water-proof outlet.
⚠Do not use supplied water hotter than 185ºF (85ºC). In order to prevent
scalding due to improper operation, set the cold water supply pressure to
higher than the hot water supply pressure or to the same pressure.
⚠Do not reverse hot and cold inlets.
⚠Do not install in the following environments: outdoors, in humid locations such
as saunas, freezing locations, or moving vehicles. If the temperature drops to
freezing, wrap the pipes with insulation.
⚠Avoid placing any objects within the detection range of the infrared sensor.
WARNINGS

3
ENGLISH
WARNINGS
⚠Always close the water shutoff valve before cleaning the filter and wait for the
filter on the hot water side to cool down.
⚠Do not clean the product with cleaning agents other than diluted neutral
detergent.
⚠ Handle the product with care. Do not subject the product to strong forces,
drops, or impacts.
⚠Only connect the controller to a GFCI protected outlet that is connected to a
surge protector rated no more than 15A. Do not use damaged or loose outlet.
⚠Do not use this product with any power supply other than specified (AC 100-
240 VAC, 50/60 Hz). The voltage supply must be separately switchable.
⚠Do not damage, modify (cut or extend), bend forcibly, twist, pull, pinch, roll up,
heat or put heavy objects on the power cord or power plug.
⚠Always unplug by holding the plug by the base. When inserting, push it in all
the way to the base. Do not wet the power plug or electrical parts or insert or
pull power plug with wet hands. Always make sure the power plug is clean of
dust or dirt. Avoid operation during thunderstorms.
⚠Make sure the power cord does not come in contact with the hot water supply
pipe.
⚠Unplug the product if it will not be used for a long period of time.
⚠Perform regular maintenance. Do not leave abnormalities, such as rattling
parts, unaddressed. At least annually, check around pipes for water leakage,
replace worn check valves, and turn the temperature control handle of the
thermal mixing valve to prevent buildup or sticking.
BEFORE INSTALLATION
Check the cold and hot water supply pressure.
The working pressure range is 15 psi - 80psi (100 kPa - 551 kPa).
Make sure to set the cold water supply pressure to higher than the hot water
supply pressure, or to the same pressure.
When the water supply pressure is higher than 80 psi (551kPa), be sure to
reduce the pressure within a range of 20 to 80 psi by using a pressure-reducing
valve (sold separately).
Check the temperature of the hot and cold water supplies.
The recommended temperature range:
HOT supply: 120ºF-180ºF (49ºC-82ºC)
COLD supply: 39ºF-80ºF (4ºC-27ºC)
Flush all water lines prior to installation .
Turn off the water supply at the supply stop.
Make sure to not damage the sensor surface during installation.
Do not place other devices that use an inverter or infrared sensor near the faucet.

4
ENGLISH
Spout assembly
Screws (8) Key
Controller Mounting brackets (2)
Check to make sure you have the following parts indicated below:
INCLUDED PARTS
TOOLS YOU WILL NEED
Drill
Phillips
Screwdriver Pencil Level Tape
Measure
SPECIFICATIONS
A F
HG
I
B
C
D
J
E
Power supply AC 100~240 V
Power Cord Length 29-1/2” (750mm)
Sensor Detection Range 5-1/8’”~ 7-7/8” (130~200mm)
Sensor is self-adjusting.
Water Supply Pressure Minimum required: 15 psi (138 kPa) (Flowing)
Maximum allowed: 80 psi (551 kPa)
Water Supply Connection 1/2-14 NSPM
Inlet Temperature range HOT: 120~180°F (49~82°C)*
COLD: 39~80°F (4~27°C)
Ambient Temperature 32~104°F (0~40°C)
Humidity Max. 90% RH
Flow Rate Maximum 1.1 gallon/min (4.2 L/min)
*Check your local plumbing codes.

5
ENGLISH
NOTE:
Before installing the faucet, be sure to
thoroughly flush the supply pipes of
dirt and debris. Then, shut off the water
supply at the stop valves. See the rough-
in dimension page to determine the
correct location for the controller.
1. Mount the inlet brackets on the wall
(ill. 1). Use wall anchors if necessary
(not provided). Brackets MUST be
mounted 3-¾” (95mm) apart (center
to center) to connect correctly to the
controller. Make sure there are no
obstructions to the inlet brackets.
IMPORTANT!
Be sure to mount each water inlet
bracket in the correct upright direction
as shown (ill. 1). Otherwise, the strainer
on the water inlet bracket will be
inaccessible for cleaning.
INSTALLATION PROCEDURE
F
G
H
I
H
I
J
J
I
95mm
2. Remove the controller cover (ill. 2).
3. Connect the controller to the water inlet brackets (ill. 3) Connect the
flexible hoses to the bracket inlets.
ill. 1
ill. 2
ill. 3
I

6
ENGLISH
4. Fasten the spout (ill. 4).
5. Cut the hoses if
necessary (ill. 5). Make
sure the cuts are square.
6. Connect the hose (ill. 6).
INSTALLATION PROCEDURE
A
B
C
ill. 4
90
A
D
ill. 5
H
D
ill. 6

7
ENGLISH
7. Insert the sensor
connectors (white x 2)
until it stops with a ‘click’
(ill. 7).
It’s no problem to insert it
in either right or left one.
Insert the (white, orange)
connectors of the LED
Unit until it stops with a
‘click’.
8. Attach the controller
cover
(ill. 8).
9. Insert the power plug
(ill. 9).
INSTALLATION PROCEDURE
7
E
H
ill. 7
F
G
H
ill. 8
ill. 9

8
ENGLISH
Turn on the water supply
Turn on the water supply at the stop valves and inspect all the
connections for any leaks (Ill. 10).
Flow rate adjustment
If flowrate adjustment is necessary because the wash basin is too small or
the water pressure is too high, turn the stop valve(s) clockwise to limit the
flow. Confirmation of wash basin specifications is highly recommended
before installation of the Automatic Faucet.
Temperature adjustment
The water temperature has been factory set at 100°F (38°C, Max: 42°C ±
3°C). Depending on the supply water pressure and other local conditions,
the water temperature may not be kept as specified. In such a case,
adjust the temperature by turning the temperature control handle (Ill. 11).
NOTE: If turning the temperature control handle changes the
temperature opposite of the direction indicated, make sure the hot water
supply is connected to the left inlet bracket.
Adjusting maximum outlet temperature
1. Shut the water off at the stop valves.
2. To decrease temperature:
Remove screw and pull handle slowly to remove. turn handle counter-
clockwise one notch and reinstall onto cartridge.
To increase temperature:
Remove screw and pull handle slowly to remove. turn handle clockwise
one notch and reinstall onto cartridge.
3. Secure handle with screw.
4. Open shut off valve.
5. Check water temperature.
**Repeat steps 1-5 if necessary.
TESTING AND CALIBRATION
Open
Close
Stop Valve
Hot
Cold
Temperature
Control
Handle
Ill. 11
Temperature Control
Handle
HOT
COLD
Open
Close
Stop valve
Ill. 10
Screw

9
ENGLISH
HOW TO USE
MODE ADJUSTMENT
Your new faucet has different
operation modes that are easy
for you to adjust by using the DIP
switches of the controller.
Water comes out when
you hold out your hand.
Hold hand over side sensor.
Temperature of the water will correspond to
the LED color on the spout. RED for HOT,
BLUE for COLD.
Placing hand next to sensor when the water
is not discharging will change the color on
the LED.
Switching between HOT and COLD water.
Starting and stopping the flow of water.
LED
(RED/HOT, BLUE/COLD)
Side Sensor
Water stops when you
withdraw your hand.
DIP switch operation

10
ENGLISH
MODE ADJUSTMENT
Hold your hand on the side sensor to switch water
temperature from HOT to COLD and COLD to HOT.
Continuous water spouting mode
Water comes out when you trigger the sensor by holding out your hands.
After 3 seconds of use, the water will remain on for a duration of 1 minute.
To stop the water, trigger the sensor a second time.
Cold water priority mode
After one (1) minute of inactivity, faucet resets to “Cold Water Setting”.
.
Equipment protection wash
When the product is not used for 24 hrs, water will come out automatically
for 5 seconds to protect the lifespan of the automatic faucet.
Cleaning mode
This mode prevents the water from coming out while you clean the lavatory.
Activate by holding your hand over the sensor for 10 seconds the LED indicator
on the spout will turn off for 5 seconds, keep your hand on the sensor while it is off.
Afterwards, no water will come out for 1 min. Afterwards, triggering the sensor
will cause water to come out as usual.
Normal mode
2
3sec 60sec
10-15sec 60sec
Mode ajustment
GB
Ajustement du mode
FR
Modo de ajuste
ES
Ajuste do modo
PT
Continuous water spouting mode
Cleaning mode
-6-