Toto UMI TX496SUN User manual

SPECIFICATIONS
OPERATING CONDITIONS
S060446S
MAINTENANCE
TROUBLESHOOTING
INSTALLATION
"UMI"3 HOLES BATH & SHOWER SET TX496SUN
1
23
5
4
6
Ø35 Hole
Ø32 Hole
Ø40 Hole
Flexible Hose
Packing
Packing
Shower
Holder
Flexible Hose
Shower
Nut
Packing
Packing
Lock Nut
Packing
Body
Lock Nut Wavy
Washer
Connector
Nut
c
H
Always wipe chrome plated area withdry soft cloth,
and sometimes wipe itwithcloth soaked in mild soap.
Packing
3. BOLT
c
H
C
L
I
CK
Packing
Hose Spring
Stopper
ToCold
Water Supply
ToHot
Water
Supply
ATTENTION
Flow Regulator Inside
(Don t remove)
1. Watersupply pressure : 0.05 ~0.75 MPa.
2. Ensure that watersupply is clean ( NoSand, Dirt, Etc. )
Shower Holder
1. NOZZLES
CHECK
POINT
Unsatisfactory spray 1 Clean
Water leaks around the handle 2 Tighten
Handle is loose 3 Tighten
PROBLEM
SOLUTION
R5
120 120
210
115
max.30
G½
7°
Ø50
Ø50
Ø50
2. CONNECTING
NUT
Ø32 Hole
Ø40
Hole
Body
Spout
Ø35
Hole
Don t use abrasive cleaning material suchas; detergentscontaining
hydrochloricacids, thinner, polishing powder, and nylon brush.
FlowRegulator should not be remove because it could damage the
system
As the product model is constantly updated, the actual product may
not look the same as it shownin the diagram, but the basic
installation principlesare the same.
2.
1.
3.

SPESIFIKASI
S060446S
PENYELESAIAN MASALAH
PEMASANGAN
"UMI"3 HOLES BATH & SHOWER SET TX496SUN
1
23
5
4
6
Ø35 Hole
Ø32 Hole
Ø40 Hole
Flexible Hose
Packing
Packing
Shower
Holder
Flexible Hose
Shower
Nut
Packing
Packing
Lock Nut
Packing
Body
Lock Nut Wavy
Washer
Connector
Nut
c
H
Packing
3. BOLT
c
H
C
L
I
CK
Packing
Hose Spring
Stopper
ToCold
Water Supply
ToHot
Water
Supply
Flow Regulator Inside
(Don t remove)
Shower Holder
1. NOZZLES
R5
120 120
210
115
max.30
G½
7°
Ø50
Ø50
Ø50
2. CONNECTING
NUT
Ø32 Hole
Ø40
Hole
Body
Spout
Ø35
Hole
KONDISI OPERASIONAL
PEMELIHARAAN
Selalu bersihkan area yang berlapis dengan kain lembut kering,
dan sesekali bersihkandengan kain yang direndam dalam sabun
yang dicampur air.
PERHATIAN
1. Tekanan sumber air: 0.05 ~ 0.75 MPa.
2. Pastikan kondisi sumberair adalah bersih
(tidak ada pasir, kotoran dan lain lain)
Jangan gunakan bahanpembersih yang bersifat abrasif seperti
deterjen yang mengandung asam klorida, tinner, bubukpolishing
dan sikat nilon.
FlowRegulator tidak boleh dilepas karena dapat merusak sistem
Karena model produk terus mengalami pembaharuan, aktual
produk mungkin tidaksamadengan gambar, tapiprinsip dasar
pemasangan adalah sama.
2.
1.
3.
Pancaran tidak memuaskan 1 Bersihkan
Air bocor disekitar handle 2 Kancangkan
Handle longgar 3 Kancangkan
MASALAH
SOLUSI
POIN
PERIKSA