Town & Country Fireplaces TC42 User manual

TC42 OUTDOOR GAS
FIREPLACE INSTALLATION
AND OPERATING
INSTRUCTIONS
150612-40 TC42.CODE 5056.426OD
MODEL
TC42.OD
SERIES C
MODULAR DIRECT VENT
OUTDOOR FIREPLACE
WARNING: If the information in these
instructions is not followed exactly, a re
or explosion may result causing property
damage, personal injury or death.
WARNING: Solid fuels should not be burned in
this appliance.
This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is
not convertible for use with other gases, unless
a certied kit is used.
WARNING: Improper installation, adjusment, al-
teration,serviceormaintenancecancauseinjury
or property damage. Read the installation, oper-
ating and maintenance instructions thoroughly
before installing or servicing this equipment.
FOR YOUR SAFETY
Do not store or use gasoline or other
ammable vapors and liquids in the vicinity
of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch.
• Do not use any phone in your building.
• Immediately call your gas supplier from
a neighbour’s phone. Follow the gas
supplier’s instructions.
• If you cannot reach your gas supplier call
the re department.
Installation and service must be performed by
a qualied installer, service agency or the gas
supplier.
INSTALLER:
Leave this manual with the appliance.
CONSUMER:
Retain this manual for future reference.
SERIAL #
WARNING: FOR OUTDOOR USE ONLY

Table of Contents
Caution ........................................................................................... 3
Safety ............................................................................................. 3
This Fireplace Is Intended For Outdoor Use Only! .........................5
Propane Conversion .......................................................................6
Fireplace Dimensions ..................................................................... 7
Minimum Clearances To Combustible Material...............................7
Installation Requirements ...............................................................8
Window Frame Removal................................................................. 8
Top Standoffs..................................................................................9
Locating The Fireplace ...................................................................9
Framing And Finishing .................................................................. 10
TC42 Steel Stud Framing Kit ........................................................ 12
Adjustable Lintel ........................................................................... 14
Hearth Extension.......................................................................... 15
Honeywell Control Valve .............................................................. 16
Plumbing and Electrical................................................................ 16
Gas Supply ................................................................................... 17
Gas Pressure Check..................................................................... 17
Venting.......................................................................................... 18
Wall Termination Venting .............................................................. 18
Wall Termination Venting Chart..................................................... 21
Roof Termination Venting Chart.................................................... 22
Vent Terminal Clearance............................................................... 25
Vent Terminal Minimum Clearances ............................................. 25
Vent Pipe Sealant ......................................................................... 26
Vent Restrictor Adjustment ...........................................................27
Firebox Panels Installation............................................................ 28
Light Bulb Replacement ............................................................... 29
Lighting Instructions .....................................................................30
First Fire........................................................................................ 30
Maintenance .................................................................................31
Replacement Parts ....................................................................... 32
Replacement Parts – Honeywell Control System ......................... 33
Wiring Diagram.............................................................................34
Wall Termination Kit ....................................................................35
Roof Termination Kit ...................................................................35
Wall Shield ................................................................................... 35
Ceiling Firestop Thimble ............................................................... 35
Vent Pipe Dimensions .................................................................36
Vent Offset Chart ..........................................................................37
Notes ............................................................................................38
Safety Label Location ...................................................................39
2
TC42.CODE 150612-40

FOR YOUR SAFETY - Do not install or operate your Town & Country replace without
rst reading and understanding this manual. Any installation or operational deviation from
the following instructions voids the Town & Country FireplacesTM Warranty and may prove
hazardous.
This appliance and its individual shut off valve must be disconnected from gas supply piping
system during any pressure testing of that system at test pressures in excess of 1/2 psig
(3.5 kPa).
This appliance must be isolated from the gas supply piping system by closing its individual
manual shut off valve during any pressure testing of the gas supply piping system at test
pressures equal to or less than 1/2 psig (3.5 kPa).
Note: When lit for the rst time, the appliance will emit a slight odour for a couple of hours.
This is due to the curing of paints, sealants and lubricants used in the manufacturing process.
This condition is temporary. Open doors and windows to ventilate area. Smoke and fumes
caused by the curing process may cause discomfort to some individuals.
Do not use the replace if any part has been under water. Immediately call a qualied service
technician to inspect the replace and to replace any part of the control system and any gas
control which has been under water.
Due to high temperatures, this gas appliance should be located out of traffic and away from
furniture and draperies.
Children and adults should be alerted to the hazards of high surface temperatures and
should stay away to avoid burns or clothing ignition.
Young children should be carefully supervised when they are in the same room as the
appliance.
Clothing or other ammable material should not be placed on or near the appliance.
Any grill, panel or door removed for servicing the unit must be replaced prior to operating.
Failure to do so may create a hazardous condition.
Installation and repair should be done by a qualied service person. The appliance should
be inspected before use and at least annually by a professional service person. More
frequent cleaning may be required due to excessive lint from carpeting, bedding material,
etc.. It is imperative that control compartments, burners and circulating air passageways
of the appliance be kept clean.
It is our policy that no responsibility is assumed by the Company or by any of its employees
or representatives for any damages caused by an inoperable, inadequate, or unsafe
condition which is the result, either directly or indirectly, of any improper operation or
installation procedures.
This appliance must not be connected to a chimney ue serving a separate solid fuel
burning appliance.
3
TC42.CODE 150612-40
Caution
Safety
We recommend that our gas hearth
products be installed and serviced
by professionals who are certied
in the United States by the National
Fireplace Institute®(NFI) as NFI Gas
Specialists
DANGER: If you smell gas:
1. Shut off gas to the
appliance
2. Extinguishanyopen ame.
3. If odor continues, keep
away from the appliance and
immediately call your gas
supplier or re department.
WARNING: Do not store or
use gasoline or other am-
mable vapors and liquids in
thevicinity ofthisor anyother
appliance.
DANGER: CARBON
MONOXIDE HAZARD
This appliance can produce
carbon monoxide which has
no odor.
Using it in an enclosed space
can kill you.
Never use this appliance in
an enclosed space such as
a camper, tent, car or home.

From Massachusetts Rules and Regulations 248 CMR 5.08:
(a) For all side wall horizontally vented gas fuelled equipment installed in every dwelling, building or structure used in whole or in part for residential
purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet above
nished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall be satised.
1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fuelled equipment, the
installing plumber or gas tter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is installed on the oor level
where the gas equipment is to be installed, in addition, the installing plumber or gas tter shall observe that a battery operated or hard-wired carbon
monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served by the side wall horizontal vented gas
fuelled equipment. It shall be the responsibility of the property owner to secure the services of qualied licensed professionals for the installation of
hard-wired carbon monoxide detectors.
a. In the event that the side wall horizontally vented gas fuelled equipment is installed in a crawl space or an attic, the hard-wired carbon monoxide
detector with alarm and battery back-up may be installed on the next adjacent oor level.
b. In the event that the requirements of this subdivision cannot be met at the time of completion of installation, the owner shall have a period of thirty
(30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon monoxide detec-
tor with an alarm shall be installed.
2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions shall
comply with NFPA 720 and be ANSI/UL 2034 listed as IAS certied.
3. SIGNAGE. A metal or plastic identication plate shall be permanently mounted to the exterior of the building at a minimum height of eight (8) feet
above grade directly in line with the exhaust vent terminal for the horizontally vented gas fuelled heating appliance or equipment. The sign shall read, in
print size no less than one-half (1/2) inch in size, “GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.
4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fuelled equipment shall not approve the installation unless,
upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5.089(2)(a) 1
through 4.
(b) EXEMPTIONS. The following equipment is exempt from 248 CMR 5.089(2)(a) 1 through 4.
1. The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54 as adopted by the
Board; and
2. Product Approved side wall horizontal vented gas fuelled equipment installed in a room or structure separate from the dwelling, building or struc-
ture used in whole or in part for residential purposes.
(c) MANUFACTURER REQUIREMENTS – GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product Approved side
wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the instructions provided by
the manufacturer for installation of the equipment and the venting system shall include:
1. Detailed instructions for the installation of the venting system design or the venting system components; and
2. A complete parts list for the venting system design or venting system.
(d) MANUFACTURER REQUIREMENTS – GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a Product Approved
side wall horizontally vented gas fuelled equipment does not provide the parts for venting the fuel gases, but identies “special venting systems”, the fol-
lowing requirements shall be satised by the manufacturer.
1. The referenced “special venting system” instructions shall be included with the appliance or equipment installation instructions; and
2. The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a parts list and detailed
installation instructions.
(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fuelled equipment, all venting instructions, all parts
lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation.
Important Note for the Commonwealth of Massachusetts:
4
TC42.CODE 150612-40

- The replace must be located inside of a weatherproof
enclosure.
- Flashingmustbeinstalled aroundthereplaceopening
in accordance with local building codes in order to
prevent moisture from entering the enclosure.
- A drip pan (not supplied with the unit) must be installed
under the replace and be provided with a means of
draining.
- Care must be taken to select materials and building
practices which will protect the enclosure and replace
from exposure to moisture.
This Fireplace Is Intended For Outdoor Use Only!
5
TC42.CODE 150612-40

Propane Conversion
Note: This fireplace comes with a
preinstalled Honeywell pilot. When
installing the burner assembly, remove
the pilot that came attached to the burner
and discard.
DO NOT USE ANY OTHER PILOT WITH
YOUR OUTDOOR UNIT OTHER THAN
THE HONEYWELL PILOT THAT CAME
INSTALLED IN THE FIREPLACE.
1. Remove the compression tting from the
bottom of the orice housing and gently tap
the pilot in your hand.The natural gas orice
should fall out. Fig. #1
2. Insert the propane orice that came
in your instruction pack as shown into the
orice housing and reattach the pilot to the
compression titng and pilot tube.
Fig. #2 & 3
3. Using the valve conversion kit that came
in the instruction pack, convert the valve to
propane following the instructions provided
with the kit. Fig. #4
Fig. #1
Fig. #2
Fig. #3
Fig. #4
ORIFICE
HOUSING COMPRESSION
FITTING
ORIFICE
COMPRESSION
FITTING
ORIFICE
VALVE
CONVERSION
KIT
ORIFICE
HOUSING
6
TC42.CODE 150612-40

52 3/8
29 7/16
43 13/16
27 3/16
53 15/16
38 3/16
11 11/16
43 13/16
Variable
42
1/4
Variable
**
24"
*
38 1/8"
4"
* MANTEL CLEARANCE
A 9”
B 6”
C 3”
** MANTEL DEPTH
D 12”
E 6 3/4”
F 1 1/2”
MANTEL CLEARANCE
CHART
Minimum Clearances:
Side standoffs....................................................... 0 in. (0 mm)
Back standoffs ...................................................... 0 in. (0 mm)
Top standoffs ........................................................ 0 in. (0 mm)
Bottom of appliance.............................................. 0 in. (0 mm)
Adjacent side wall................................................. 4 in. (102 mm)
Ceiling to appliance ............................................24 in. (610 mm)
*Mantel to appliance .................. ..........See Figure #2
**Maximum Mantel extension .. ..........See Figure #2
Mantel support...................................................... 4 in. (102 mm)
Vertical vent pipe ..........................................1 3/4" in. (45 mm)
Horizontal Vent pipe (Top, sides and bottom) 1 3/4" in. (45 mm)
Fig. #5
Fig. #6
Fig. #7
MAY USE COMBUSTIBLE
FACING MATERIAL IN THIS AREA
NON-COMBUSTIBLE
FINISH MATERIAL
SEE FIG #8
NON-COMBUSTIBLE ZONE.
DO NOT INSTALL ANY COMBUSTIBLE MATERI-
AL, ELECTRICAL WIRING OR GAS PLUMBING IN
THIS AREA.
COMBUSTIBLE FRAMING AND
FINISH WALL ABOVE STANDOFFS
STANDOFFS
STEEL FRAMING
FIREPLACE FRONT
TOP OF LINTEL BAR
A
BC
D
E
F
24”
38 3/16”
4”
MANTEL
ADJACENT WALL
OR MANTEL
SUPPORT
CEILING
UNIT MAY BE RECESSED UP TO 6” WITH
NON-COMBUSTIBLE MASONRY TYPE MATERIAL
7
TC42.CODE 150612-40
Fireplace Dimensions
Minimum Clearances To Combustible Material

The Town & Country Fireplace installation and venting must conform to the current
CAN/CGA-B149 installation code (in Canada) or the current National Fuel Gas Code,
ANSI Z223.1 (in the USA), and approved per local codes. Only qualied (licensed or
trained) personnel should install this product.
In the state of Massachusetts, only a licensed Plumber and Gas Fitter may install
this product.
Warning: Turn off the replace, and allow ample time for the unit to cool before
proceeding.
Caution: The ceramic glass is very fragile, and should be handled with care.
The window frame is held in place by two spring-loaded latches that are operated by a
one-piece latch handle.
1. Remove the stainless steel trim (one piece).
2. Using a screwdriver or other similar object, push against the notch in the top of the
latch and grab the bottom of the latch handle as it protrudes. Lift handle until latch hook
disengages. Repeat for other side while holding glass so it does not tip out.
3. Tilt the top of the window frame out to clear the top edge of the unit. Grasp the sides of
the frame and lift up and out to disengage from its bottom track.
4. Place the window frame in a safe place to avoid damage.
5. Re-assemble in reverse order. Latch handle should snap into place and be ush with
window frame when engaged correctly.
STAINLESS STEEL
LATCH HANDLE
TIP:
To ensure glass is properly latched, grasp the top left and
right sides of the glass frame, under moderate pressure it
should pull forward and return to original position evenly on
both sides.
STAINLESS STEEL
DOOR FRAME
Fig. #8
Fig. #9
8
TC42.CODE 150612-40
Installation Requirements
Window Frame Removal

The top standoffs are shipped loose inside
the replace and must be installed on top of
the replace as shown in Fig #10. Do this
once the replace is on site and in position.
In planning the installation for the replace, it is necessary to determine where the unit is to
be installed, location of vent system and where gas supply piping may be plumbed.Various
installations are possible, such as, into an existing wall, a corner, a built-in wall or a wall
projection (Fig #11). Due to high temperatures, do not locate this replace in areas of high
traffic or near furniture or draperies.
The minimum clearances from the replace to combustible surfaces must be adhered
to and are shown in Fig #6 and Fig #7.
Fig. #10 TOP STANDOFFS
EXAMPLES OF COMMON LOCATIONS
SEE FIG #11 FOR DIMENSIONS
Fig. #11
9
TC42.CODE 150612-40
Locating The Fireplace
Top Standoffs

ರ
ರ
Note: The replace should be in place
and venting installed before framing in or
building an enclosure around the unit.
The Town & Country replace must be
framed in as described below or totally en-
closed with non-combustible material, such
as facing brick.
Determine the total thickness of facing
material to be used. A thickness of 3/4" will
allow the nishing surface to be ush with
the front of the unit. If preferred, additional
masonry type non-combustible material can
be installed above and to the sides up to 6
inches proud of the appliance.
The nishing material must not interfere
with glass frame access.
A Steel Stud Framing Kit is supplied with the
replace and must be used unless the
replace is totally enclosed with
non-combustible material.Assemble the fram-
ing kit as per the instructions on pages 12 &
13 of this manual. Attach the steel frame to
the replace once the replace is in its nal
position.Secure the steel frame to the framing
brackets on each side of the unit.Ensure that
the studs are set back far enough to allow for
thickness of nishing surface.
The sides, back and top of the replace can
be framed in up to the steel studs and the
replace standoffs using conventional
lumber. Consult local building codes for
specic requirements.
Due to high temperatures, non-combustible
backer board, such as cement board or its
equivalent, must be used to sheet in the front
of the replace, extending 12" above and 5
1/2" to the side of the framing edge bars.(Fig
#9) Standard sheet rock (dry wall) may be
used beyond this.
If the backer board is not to be nished with
other non-combustible material such as tiles,
it is recommended that the instructions in
Fig.#14 be followed closely.
Fabricate and install appropriate ashing to
local building code.
Note: Installing unit without ashing
installed will void the warranty
Note: Provide proper drainage to divert
water underneath the unit
Chase Insulation: When installing this
replace against a non-insulated exterior wall
or chase, it is recommended that the outer
walls be insulated to same degree as other
exterior walls. Do not place replace directly
against the insulation. Cover the insulation
and plastic vapour barrier with a solid surface,
such as dry wall (sheet rock). Consult local
codes. Do not insulate or use plastic vapour
barrier within the framing kit.
CAUTION: SEE FIGURE #14 BEFORE
PROCEEDING.
IT IS HIGHLY RECOMEND-
ED THAT A FULL HEADER
BE INSTALLED ABOVE THE
METAL FRAMING KIT
ALL OTHER FRAMING CAN
BE DONE WITH
CONVENTIONAL LUMBER
Fig. #12
NON-COMBUSTIBLE ZONE. DO NOT INSTALL ANY
COMBUSTIBLE MATERIAL, ELECTRICAL WIRING, INSU-
LATION, PLASTIC VAPOR BARRIER OR GAS PLUMBING
WITHIN THE STEEL STUD FRAMING
STEEL STUD FRAMING KIT DIMENSIONS
(Supplied with replace)
10
TC42.CODE 150612-40
Framing And Finishing

12”
5 1/2”
54"
56 1/4"
62"
21 1/4"
30"
3/4"
56 1/4"
87 11/16"
62"
Fig. #14
CALCIUM SILICATE
BOARD
MAXIMUM FACING DEPTH
IF FINISHINGTHEWALLABOVETHE
UNIT WITH PAINT, THE FRAMING
KIT SHIPPED WITH THE UNIT
SHOULD BE DISCARDED.
IT IS RECOMMENDEDTO USE FULL
SHEETS OF CALCIUM SILICATE
BOARD OR ITS EQUIVALENT AND
FULL LENGTH METAL STUDS TO
FINISH AND FRAME AROUND THE
UNIT.
FOLLOW THE MANUFACTURERS
MOUNTING AND FINISHING IN-
STRUCTIONS CLOSELY.
NON-COMBUSTIBLE BOARD DETAIL
Fig. #13
Fig. #15
Fig. #16
NON-COMBUSTIBLE MATERIALS
MUST EXTEND 12" ABOVE AND 5
1/2" TO THE SIDES OF THE FRAM-
ING EDGES.
MINIMUM COMBUSTIBLE
FRAMING DIMENSIONS
NOTE: FIREPLACE SHOULD BE IN ITS FINAL LOCATION BEFORE FRAMING.
NON-COMBUSTIBLE RECESSED
INSTALLATION DETAIL
STEEL STUDS
NON-COMBUSTIBLE
MATERIAL
26 1/8"
56 1/4"
12 5/8"
3/4"
Including Sheetrock
NON-COMBUSTIBLE
BOARD
NON-COMBUSTIBLE
BOARD
11
TC42.CODE 150612-40

2
4
5
6
Each Kit Contains: Item Part # Description Qty.
1 5049.9912 SCREW, TEKS Pkg
#8 x 1/2” 40
2 9093.03 STUD, SIDES,
53 3/4”L 2
3 9093.1 STUD, OUTER
SIDES, 53 3/4”L 2
4 9935.000 STUD, CENTER,
14 15/16”L 2
5 9094 STUD, HEADER,
56 1/8”L 1
6 9934.000 STUD, PLATE,
47 15/16”L 1
7 9945.000 BASE PLATE ,
6 1/2”L 2
8 5049.993 SCREW, DRYWALL, Pkg
1 1/4” 30
1. Top Frame Assembly
• Lay out side studs (2) and center studs
(4) on a large at surface. (Fig #17)
• Using the screws provided (1), attach the
header stud (5) and the plate stud (6) to
the center studs (4).
TC42.ODFRKIT
Fig. #17
1
2
3
4
5
6
7
8
12
TC42.CODE 150612-40
TC42 Steel Stud Framing Kit

3
7
5
Framing
Brackets
5
7Access holes to
mounting screws
2. Attach Side Studs (Legs)
• Attach the outer side studs (3) to the top
of the header stud (5). (Fig #18)
• Fasten the outer side studs (3) at the
bottom using the base plates (7).
3. Attach the Assembled Frame to
the Unit
• Align the assembled frame to the unit
framing brackets. (Fig #19) Attach
at the fastening points through the
access holes in the outer side studs
(3).
4. Secure to Existing Framing
• Secure the frame assembly to existing
framing through the stud header (5) and
the stud plates (7).
5. Install Non-combustible Board on
Top and Sides
Fig. #18
Fig. #19
Fig. #20
13
TC42.CODE 150612-40

Adjustable Lintel
Fig. #21
Fig. #22
Fig. #23
1. The adjustable lintel assembly has two
orientations for desired nishing. A anged
edge and a hemmed edge.The lintel comes
factory installed with the ange edge out. If
the desired edge is different from the factory
setting, use the following steps to change
it(Fig.#21).
2. Remove the window trim by lifting and
pulling to disengage from the window frame
(Fig.#22).
3. Remove the lintel. Rotate the assembly
to have the desired edge away from the
replace(Fig .#23).
4. The lintel assembly has a maximum range
of adjustability of 1”to accommodate varying
facing material thicknesses. The maximum
depth is 6” (Fig.#25).
5. The lintel assembly can then be adjusted
to align ush with your facing material by
sliding in or out approximately 1”.
6. Tighten the lintel attachment screws posi-
tioned at the top and bottom on each side
of the lintel assembly (Fig.#23).
7. Re-attach the window trim.
HEMMED EDGE
FLANGED EDGE
TRIM
LINTEL
ATTACHMENT
SCREW
14
TC42.CODE 150612-40

1/4"
1"
MAX
WINDOW
FRAME
HEARTH
EXTENSION WINDOW
TRACK
SUB-
FLOOR
Caution: While a hearth extension is not required and combustible ooring materi-
als may be brought directly up to the replace, many materials (such as wood oor-
ing) may not tolerate the radiant heat from this replace, resulting in discoloration,
shrinking and cracking. For this reason, we suggest a non-combustible hearth that
is no more than 1” above the bottom of the replace. If thicker, replaced must be
raised accordingly.
Caution: Hearth extensions thicker than 1” will interfere with the window frame.
SIDE FACING
CLEARANCES
ROCK FACE
AREA
MINIMUM
6”
43 7/8”
This replace may be recessed up to a
maximum depth of 6”. This recess must
be constructed from non combustible
material. The space between the
outside lintels and the rebox must be
completely free of any debris and the
window with trim tted must be able
to move freely. No building material
is permitted to protrude past the lintel
bars attached to the replace under
ANY circumstance.
37 3/4”
MINIMUM
Fig. #24
Fig. #25
15
TC42.CODE 150612-40
Hearth Extension

The gas control system is located on the right hand side of the rebox behind an access panel
and the decorative rebox panel (if installed). The replace is operated via a wall switch.
The wall control is connected to the replace by a 14-2 AWG wire, not supplied with the
replace.
Installation
1. Place the replace in the desired location.
2. Remove the window from the replace.
3. Remove access panel from right hand side of the rebox (Fig #26)
4. Remove the cover from the electrical box Fig. #27.
5. Run two 110 V. AC switched electrical supplies to the control box and connect to the
terminal block installed inside the control box(Fig #28). The replace operates on 24V
AC supplied by a transformer rated at 110 volts, 60Hz. See wiring diagram on page #31
for correct connections on terminal block.
6. Connect the gas supply to the valve (Fig #29)
ELECTRICAL BOX
COVER
GAS INLET
Fig. #29
Fig. #28
Fig. #27
TERMINAL BLOCK,
ELECTRICAL CONNECTIONS
ACCESS PANEL
Fig. #26
16
TC42.CODE 150612-40
Honeywell Control Valve
Plumbing and Electrical

SUPPLY
PRESSURE
MANIFOLD
PRESSURE
Caution: The gas line should be installed by a qualied service person in accordance with
all building codes. This section is intended as a guide for qualied technicians installing this
appliance. Consult local and / or national building codes before proceeding.
• Gas supply line access holes are located at the top and left sides of the Control Box.
Gas valve inlet accepts a 1/2" N.P.T. tting. Correct gas line diameter must be used to
assure proper operation and pressure.
• The replace has an input rate of 61,000 BTU/HR on both Natural Gas and Propane.
• NOTE: A sediment trap, as per national fuel gas code, must be installed in the
gas supply line no more than 6 feet from the gas control valve to minimize the
possibility of any loose scale or dirt within the gas supply line from entering the
control valve.
• DO NOT HARD PIPE GAS LINE TO VALVE. A method of disconnecting the valve
from the gas line such as a union or are tting must be provided to allow for repair or
replacement of the gas valve.
• It is essential that a union or anged connection be installed just upstream of the
valve and inside the control compartment to allow for repair or replacement of the
gas valve.
Check local codes for additional requirements.
1. Connect the gas supply to the valve (Fig. #29)
2. Turn on the gas supply and check that all connections are tight and leak free.
WARNING:The access panel including gasket must be
reinstalled after conversion/ installation or servicing
has been completed. Failure to do so will cause
overheating and premature failure of the control system.
Correct gas pressure requirement:
Natural Gas Propane
Min. Pressure 5.0" WC 12.5" WC
(For purpose of input adjustment)
Max. Pressure 13.9" WC 13.9" WC
Manifold Pressure
Maximum 3.8" WC 11" WC
Minimum 2.1" WC 5.5" WC
Note:To test the gas pressure, turn off the gas supply before removing the plug from
the supply pressure test port or manifold pressure test port.
Verify gas pressures with the replace lit and on the highest setting.
Please refer to the Burner Installation Manual for gas pressure testing procedure.
Fig. #30
17
TC42.CODE 150612-40
Gas Supply
Gas Pressure Check

Wall opening:
Determine the exact position of the replace so that the vent pipe is centered (if possible)
between two building framing members. Consult your local building codes prior to proceed-
ing. The vent kit will accommodate up to a maximum wall thickness of 12 inches.
1. Having determined the position of the replace, cut and frame a 14 1/2 inch opening
centred at a minimum height of 74 1/4 inches above the oor. The opening may be
round or square. Height of the opening will vary with each installation. As the horizontal
vent run increases, so does the minimum vertical rise (see Fig. #35).
IMPORTANT: When locating the opening, it should be noted that vent terminal
clearances must be maintained. See "Vent Terminal Clearances" section for proper
clearances.
A minimum 2 foot length of pipe is required off the top of the replace for any wall termina-
tion. With this minimum vertical rise in combination with a 90° elbow, a maximum horizontal
run of 18 inches is permitted (see Fig. #32 and 33). For longer horizontal runs greater than
18 inches, increase vertical rise appropriately.
The rise and run must be constrained to the boundaries of the chart shown in Fig. #32. The
horizontal run of vent must have a 1/4" rise for every 1 ft. of run towards the termination.
Before installing venting for this unit, the installer should read these instructions to ensure
that the proper vent conguration has been selected.
Use only Town and Country Termination kits:
TCVT.WTA - Wall Termination Kit
TCVT.RTA - Roof Termination Kit
Vent system components approved for use with the Town and Country Fireplace are shown
in Fig. #33.
Various combinations of vertical and horizontal runs may be used. Refer to Fig. #35 and
#36 for details. For optimum performance and ame appearance, keep the vent length
to a minimum and limit the number of elbows. Connections between each vent system
component must be tightly joined, secured with sheet metal screws and sealed with high
temperature self adhesive tape. A horizontal run of vent should have a 1/4" rise for every 1
ft. of run towards the termination.
CAUTION: UNDER NO CONDITION SHOULD COMBUSTIBLE MATERIAL BE CLOSER
THAN 1 3/4 INCHES FROM THE TOP AND 1 3/4 INCHES FROM THE SIDES OF A
HORIZONTAL SECTION AND 1 3/4 INCHES FROM THE VERTICAL SECTIONS OF THE
VENT PIPE.
18
TC42.CODE 150612-40
Venting
Wall Termination Venting

WALL THIMBLE AND VENT MUST NOT PROTRUDE BEYOND SIDING
Fig. #31
Wall thimble:
Where a vent pipe passes through a combustible wall, a wall thimble/shield must be used
to retain insulation and maintain proper clearances. The wall thimble may be cut to length
for various wall thicknesses up to 12" thick.
Measure the wall thickness including the siding. Trim the shield to match the wall thickness.
Position the wall thimble from inside through the 14-1/2" opening. Properly adjusted, the
thimble should be ush with the outer wall surface.
TRIM TO LENGTH
Fig. #32
Vent System Components Town & Country
12" Pipe Length .................................................... TCVT.811X12
18" Pipe Length .................................................... TCVT.811X18
24" Pipe Length .................................................... TCVT.811X24
48" Pipe Length .................................................... TCVT.811X48
12" Adjustable Pipe Length................................... TCVT.811X12ADJ
45° Elbow ............................................................. TCVT.811XLB45
90° Elbow ............................................................. TCVT.811XLB90
Wall/Offset Support .............................................. TCVT.811XOS
Wall Termination Kit .............................................. TCVT.WTA
Roof Termination Kit ............................................. TCVT.RTA
Wall Shield/Ceiling Firestop .................................. TCVT.THIMA
Roof Flashing, Adjustable ..................................... TCVT.811FLADJ
Roof Flashing, Flat ............................................... TCVT.811FLFLT
Roof Flashing, Steep ............................................ TCVT.811FLSTP
or any ashing that ts 11" pipe
Fig. #33
19
TC42.CODE 150612-40

Vent pipe:
Install vent pipe through the wall thimble and attach to ue outlet collar on top of the replace.
Secure all joints with screws and seal with approved "High Temp." self-adhesive aluminum
tape provided.
Adjust the replace position so that the vent pipe does not protrude beyond the outer
wall.The vent connector on the termination will accomodate walls up to 12" thick.
Wall vent terminal:
1) Engage the terminal with the vent pipe and slide terminal into place. Ensure that both
inner and outer pipes are fully engaged and then attach the terminal to the outside wall.
The vent terminal must not be recessed into the exterior wall or siding.
2) Caulk in place to prevent any moisture entering the building.
NOTE: MINIMUM CLEARANCES TO THE VENT TERMINAL MUST BE MAINTAINED
(see page #25 Fig. #40 & #42).
Fig. #34
HORIZONTAL
TERMINAL
TCVT.WTA
14 1/2" FRAMED
OPENING
WALL SHIELD THIMBLE
TCVT.THIMA
ELBOW
TCVT.811XLB90
24"
VENT PIPE
TCVT.811X24
12" VENT PIPE
TCVT.811X12
* Minimum height from the oor to center of the
opening with a maximum horizontal run of 18"
from the center of the ue outlet to the outside
face of the outer wall.The height will need to be
increased if a longer horizontal pipe is required.
*74 1/4"
20
TC42.CODE 150612-40