Town & Country Fireplaces TC36ST User manual

For reference only. Consult Manual before installation
1 TC36ST.CE 210611-11
for
architects
&
designers
Fireplace and Venting Specications
Model TC36ST Series C
IMPORTANT
This booklet is intended as a basic
specication guide for architects,
designers and builders. Please
refer to the Instruction Manual
supplied with the replace for
detailed information regarding
installation and operation.
Product installation manuals can
also be viewed at:
www.townandcountryreplaces.com
TC36 See-Thru
Series C

2 TC36ST.CE 210611-11
For reference only. Consult Manual before installation
Fireplace Dimensions
Examples of Common Locations
TC36ST.CE Cad Drawing
Available at
www.townandcountryreplaces.com
56 1/4
37 1/2
23 3/4
27 3/16 29 1/8
11 5/8
6 13/16
11 7/8
14 3/16
23 3/4
32 1/8
48
37 1/2
46 5/16
32 1/8
5 15/16

3 TC36ST.CE 210611-11
For reference only. Consult Manual before installation
Mantel Clearance Chart
Minimum Clearances to Combustibles
UNIT MAY BE RECESSED UP TO
6" WITH NON-COMBUSTIBLE
MASONRY TYPE MATERIAL
A 9" D 12"
B 6" E 6 3/4"
C 3" F 1 1/2"
REF. MANTLE CLEARANCE REF. MANTLE EXTENSION
Side standoffs...................... 0 in. (0 mm)
Back standoffs..................... 0 in. (0 mm)
Top standoffs ....................... 0 in. (0 mm)
Bottom of appliance............. 0 in. (0 mm)
Adjacent sidewall................. 2 in. (51 mm)
Ceiling to appliance ........... 24 in. (610 mm)
Mantel to appliance.........................See above
Maximum mantel extension ..........See above
Mantel support..................... 2 in. (51 mm)
Vertical vent pipe ............... 1 3/4" (45mm)
Horizontal vent pipe
(Top, sides and bottom)..... 1 3/4" (45mm)
*
**
MAY USE COMBUSTIBLE
FACING MATERIAL IN THIS AREA
NON-COMBUSTIBLE
FINISH MATERIAL
SEE FIG #7
NON-COMBUSTIBLE ZONE.
DO NOT INSTALL ANY COMBUSTIBLE MATERIAL,
ELECTRICAL WIRING OR GAS PLUMBING IN THIS
AREA.
COMBUSTIBLE FRAMING AND
FINISH WALL ABOVE STANDOFFS STANDOFFS
STEEL FRAMING
FIREPLACE FRONT
TOP OF LINTEL BAR
MANTEL
ADJACENT WALL
OR MANTEL SUPPORT
CEILING

4 TC36ST.CE 210611-11
For reference only. Consult Manual before installation
Minimum Combustible Framing Dimensions
Steel Stud Framing Kit Dimensions
Kit supplied with unit
Non-combustible board (or
other non-combustible
material) must extend 12"
above and 9 3/4" to the sides
of the framing edges.
NON-COMBUSTIBLE
BOARD
All other framing can be done with
conventional lumber
Non-combustible Zone.
Do not install any
combustible material,
electric wiring,
insulation, plastic
vapour barrier or
gas plumbing
within the steel
stud frame.
NOTE: Fireplace should be in its nal location before framing.
Non-combustible
Board Detail
NOTE:
For clarity only one
face of the two-sided
replace is shown
with steel stud framing
kit attached. Both faces
must be framed with
the steel stud framing
kit supplied with the
replace.
7 1/2”
58 5/8”
22 3/8”
3/4”
3/4”
58 5/8”
48”
58 5/8"
57 1/4"
9 3/4"

5 TC36ST.CE 210611-11
For reference only. Consult Manual before installation
Town and Country C Series replaces include our award
winning Maestro controls.
They include an elegant, programmable remote control
with a count-down timer, weekday/weekend on/off timer,
manual control and thermostat mode (where permitted),
and an easy to read LCD display.
They also come with a small, wall-mounted control which
permits on/off operation, ame modulation and houses
the battery back-up system for operation during power
outages.
Maestro controls use an on-demand electronic ignition
system, a green alternative to standing pilots, which can
cut your annual fuel consumption up to 74%.
Maestro Control System
Up to 50 Feet
WINDOW
FRAME
HEARTH
EXTENSION
WINDOW
TRACK
SUB-FLOOR
Side Facing Clearances
Caution: While a hearth extension is not required and
combustible ooring materials may be brought directly up to
the replace, many materials (such as wood ooring) may
not tolerate the radiant heat from this replace, resulting in
discoloration, shrinking and cracking. For this reason, we
suggest a non-combustible hearth that is no more than 1”
above the bottom of the replace. If thicker, replace must
be raised accordingly.
Caution: Hearth extensions thicker than 1” will interfere with
the window frame when opening.
NON COMBUSTIBLE
FINISH MATERIAL
FRAMING
EDGES
GLASS
FRAME
Hearth Extension
Caution: This replace may be recessed up to a maxi-
mum depth of 6". This recess must be constructed from
non combustible material.The space between the outside
framing edge and the rebox must be completely free of
any obstructions or debris and the window, with trim t-
ted, must be able to move freely. No building material is
permitted to protrude past the framing edges attached to
the replace under ANY circumstance.

6 TC36ST.CE 210611-11
For reference only. Consult Manual before installation
Direct Vent
Wall Installation
Direct Vent
Roof Installation
14 1/2"
FRAMED
OPENING
24" VENT
PIPE
ELBOW
12" VENT PIPE
WALL SHIELD THIMBLE
HORIZONTAL
TERMINAL
* Minimum height from the oor to center of the opening with
a maximum horizontal run of 32 1/2" from the center of the ue
outlet to the outside face of the outer wall.The height will need
to be increased with longer horizontal pipe.

7 TC36ST.CE 210611-11
For reference only. Consult Manual before installation
Wall Termination Venting Charts
TCVT Wall Vent
Cad Drawing
Available at
www.townandcountryreplaces.com
NOTE: The vent must not exceed a total
length of 68 feet. Any combination of rise
and run may be used but must be constrained
to the boundaries of this chart. A total of 3
90° elbows or combination of other elbows
equalling 90° can be used without reducing
horizontal run. For each additional 90° elbow,
or an equal combination of elbows, reduce
horizontal vent run by 2 feet. Ensure vent
pipe is properly supported.
** All dimensions are approximate.
Both rise and run may vary with different combinations of pipe.
12" Pipe
length
minimum
A
Minimum rise
B
Pipe length
C
Maximum run
D
Pipe length Max.
61" 1-12" 32 1/2" 1-24"
67" 1-18" 75 3/4" 1-48" 1-12"
73" 1-24" 9' 3 3/4" 2-48"
77 1/4" 1-12" 1-18" 13' 2" 3-48"
83 1/4" 1-24" 1-12" 17' 1/4" 4-48"
89 1/4" 1-24" 1-18" 18' 10 1/2" 1-48" 1-24"
97" 1-48" 20' 10 1/2" 5-48"
For other rise/run combinations see chart below
**

8 TC36ST.CE 210611-11
For reference only. Consult Manual before installation
Roof Termination Venting Charts
TCVT Roof Vent Cad Drawing
Available at
www.townandcountryreplaces.com
** All dimensions are approximate. Both rise and run may vary with different
combinations of pipe.
12" Pipe
length
minimum
**
A
Minimum rise
B
Pipe length
C
Maximum run
D
Pipe length Max.
61" 1-12" 41" 1-24"
67" 1-18" 75 1/4" 1-48" 1-12"
73" 1-24" 9' 3 3/4" 2-48"
77 1/4" 1-12" 1-18" 13' 2 1/2" 3-48"
83 1/4" 1-24" 1-12" 16' 113/4" 4-48"
89 1/4" 1-24" 1-18" 18' 10" 1-48" 1-24"
97" 1-48" 20' 10" 5-48"
For other rise/run combinations see chart below
NOTE: The vent must not exceed a total length of 68
feet. Any combination of rise and run may be used
but must be constrained to the boundaries of this
chart. A total of four 90° elbows, or combination
of other elbows equalling 90°, can be used without
reducing horizontal run. For each additional 90°
elbow, or an equal combination of elbows, reduce
horizontal vent run by 2 feet. Ensure vent pipe is
properly supported.

9 TC36ST.CE 210611-11
For reference only. Consult Manual before installation
M
K
I
A
V
G
G
H
A
J
V
G
A
B
C
A
V
V
A
V
B
F
B
L
V
E
V
V
V
D
A= *12 inches (30 cm) min. Clearances above grade, veranda, porch, deck, or balcony
B= *12 inches (30 cm) min. Clearance to window or door that may be opened
C= 12 inches (30 cm) min. Clearance to permanently closed window recommended to prevent condensation on window
D= 30 inches (76 cm) min. Vertical clearance to ventilated soffit located above the terminal within a horizontal distance of 2 feet (60 cm) from the
edge of the terminal
E= 30 inches (76 cm) min. Clearance to unventilated soffit
F= 6 inches (15 cm) min. Clearance to outside corner
G= 6 inches (15 cm) min. Clearance to inside corner
H= 3 feet (90 cm) min. *Not to be installed above a meter/regulator assembly within 3 feet (90 cm) horizontally from the center-line of the
regulator
I= *6 feet (1.8 m) min. Clearance to service regulator vent outlet
J= *12 inches (30 cm) min. Clearance to non-mechanical air supply inlet to building or the combustion air inlet to any other appliance
K= *6 feet (1.8 m) min. Clearance to a mechanical air supply inlet
L= *7 feet (2.1 m) min. ^ Clearance above paved side-walk or a paved driveway located on public property
M= **30 inches (76 cm) min Clearance under veranda, porch, deck, or balcony
^ a vent shall not terminate directly above a side-walk or paved driveway which is located between two single family dwellings and serves both dwellings*
** only permitted if veranda, porch, deck, or balcony is fully open on a minimum of 2 sides beneath the oor*
* as specied in CAN/CSA B149 Installation Codes, Note: local Codes or Regulation may require different clearances
* for U.S.A. Installations follow the current National Fuel Gas Code, NFPA54 /ANSI #Z21.50.b
AIR SUPPLY INLET
VENT TERMINAL GAS METER
FIXED
CLOSED
FIXED
CLOSED
OPEN-
ABLE
OPEN-
ABLE
AREA WHERE TERMINAL
IS NOT PERMITTED
Vent Terminal Minimum Clearances
36"
See Fig. #40b
48"
ADJACENT
24"
(91.5 cm)
(61 cm)
(122 cm)
STRUCTURES
OR FENCE
Minimum clearances to the vent terminal must be maintained as
shown (See illustration to right & below). Measure clearances to the
nearest edge of termination hood. (See pitch table below).
NOTE: Vent terminal must not be recessed
NOTE: LOCAL CODES OR REGULATIONS MAY REQUIRE
DIFFERENT CLEARANCES.
Roof Pitch Table (minimum)
ft m
Flat to 6/12 1.00 0.30
Over 6/12 to 7/12 1.25 0.38
Over 7/12 to 8/12 1.50 0.46
Over 8/12 to 9/12 2.00 0.61
Over 9/12 to 10/12 2.50 0.76
Over 10/12 to 11/12 3.25 0.99
Over 11/12 to 12/12 4.00 1.22
VENT TERMINAL MINIMUM CLEARANCES
TO ADJACENT STRUCTURES
Vent Terminal Clearance
See Roof Pitch Table

10 TC36ST.CE 210611-11
Optional Power Vent
Power Vent Terminals
Cad Drawings available at www.townandcountryreplaces.com
Reach almost any room or commercial setting.
Optional Power Venting allows runs up to 110’ from
an outside wall or roof surface. Vent horizontally or
vertically with up to six 90-degree elbows, including
runs up to 3’ below the replace.
The premium Power Vent fan runs quietly outside,
at the exterior terminal.
Direct Vent Terminals
Cad Drawings available at www.townandcountryreplaces.com
Wall Termination Roof Termination Flush Mount
Horizontal Termination
Standard Venting Standard Venting Stainless Steel Standard Venting
Roof Termination Wall Termination Termination for Condo Installation

Printed in Canada
For personal service pertaining to specic projects, contact:
Town & Country Architect Resource Planner
architects@pacicenergy.net
Web: www.townandcountryreplaces.com
Phone: [phone]
Toll Free: 1-877-715-2664
2975 Allenby Road, Duncan, BC Canada V9L 6V8