Town & Country Fireplaces HELIFIRE 360 User manual

Visit www. townandcountryfireplaces.net for the most up-to-date version of this manual
280116-32 HELIFIRE 360 5055.64-A
WARNING: If the information in these
instructions is not followed exactly, a re or
explosion may result causing property damage,
personal injury or death.
FOR YOUR SAFETY
Installation and service must be performed
by a qualied installer, service agency or the
gas supplier.
WHAT TO DO IF YOU SMELL GAS
• Donottrytolightanyappliance.
• Donottouchanyelectricalswitch.
•Donotuseanyphoneinyourbuilding.
• Immediatelycallyourgassupplierfrom
a neighbour’s phone. Follow the gas
supplier’s instructions.
• Ifyoucannotreachyourgassuppliercall
the re department.
Do not store or use gasoline or other ammable
vapors and liquids in the vicinity of this or any
other appliance.
This appliance may be installed in an aftermarket
permanently located,manufactured home (USA only)
or mobile home, where not prohibited by local codes.
This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is
not convertible for use with other gases, unless a
certied kit is used.
This appliance is suitable for installation in a
bedroom or bed sitting room.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
HELIFIRE 360
INSTALLATION
AND OPERATING
INSTRUCTIONS
MODEL: HELIFIRE 360
HELIFIRE 360 SEE THRU
POWER VENTED / DIRECT VENT
FIRE FEATURE - SERIES: A
NATURAL GAS ONLY

HOT GLASS WILL CAUSE
BURNS.
DO NOT TOUCH GLASS UNTIL
COOLED.
NEVER ALLOW CHILDREN TO
TOUCH GLASS.
!
DANGER
2TCHF.22BODYA_ 151215-32
TCHF.22STBODYA
5055.64-A
Table of Contents
Caution ............................................................................ 3
Safety .............................................................................. 3
Owners Information
Important Note for the
Commonwealth of Massachusetts ................................ 4
Congratulations on your purchase
of a Town & Country Helifire 360 Feature....................... 5
Helifire 360 Specifications ............................................. 5
Fire feature Dimensions ................................................. 6
Installation Requirements .............................................. 7
Door Frame Removal/Installation .................................. 7
Manufactured (Mobile) Homes ...................................... 7
First Fire .......................................................................... 8
Special Operator Note .................................................... 8
Locating the Helifire 360 ................................................ 8
Helifire 360 Orientation ................................................... 9
Installers Information
Framing and Finishing .................................................. 10
When using outdoor ashing .................................. 11
Framing Options ........................................................... 12
Gas Connection ............................................................ 14
Gas Supply ................................................................... 14
Gas Pressure Testing Procedure ................................. 14
Gas Pressure Check ..................................................... 15
Burner and Igniter ........................................................ 15
Accessing / replacing the orice............................. 15
Removing the Burner Control / Valve assembly ..... 16
Electrical Connection ................................................... 18
Helire 360 electrical connection............................ 18
Power vent electrical connection............................ 18
Wall Switch.............................................................. 19
Electrical Diagram ........................................................ 20
Venting Requirements .................................................. 21
Exterior wall opening............................................... 21
Vent Stand-Offs....................................................... 22
Surface Mount Power Vent ..................................... 23
Combustion Air Intake Restrictor............................ 23
Surface Mount Power Vent
(Vertical or horizontal termination). .......................... 24
Flush Mount Power Vent ......................................... 24
Stud Supports......................................................... 25
Venting through combustible ceiling or oor ......... 25
Power venting - exible venting connection ........... 25
Exhuast venting options.......................................... 25
Vent Terminal Minimum Clearances ............................ 26
Power Venting
Clearances.............................................................. 26
Maintenance ................................................................. 27
Glass Panel ............................................................. 27
Periodically.............................................................. 27
Replaceable Parts ........................................................ 28
Lighting Instructions ..................................................... 29
Rating label ................................................................... 30

Owners Information
This appliance and its individual shut off valve must be disconnected
from gas supply piping system during any pressure testing of that
system at test pressures in excess of 1/2 psig (3.5 kPa).
This appliance must be isolated from the gas supply piping system by
closing its individual manual shut off valve during any pressure testing of
the gas supply piping system at test pressures equal to or less than 1/2
psig (3.5 kPa).
Note: When lit for the rst time, the appliance will emit a slight odour for
a couple of hours. This is due to the curing of paints, sealants and lubri-
cants used in the manufacturing process. This condition is temporary.
Open doors and windows to ventilate area. Smoke and fumes caused
by the curing process may cause discomfort to some individuals.
Do not use the re feature if any part has been under water. Immediately
call a qualied service technician to inspect the re feature and to
replace any part of the control system and any gas control which has
been under water.
Due to high temperatures, this gas appliance should be located out of trafc and away from furniture and
draperies.
Children and adults should be alerted to the hazards of high surface temperatures and should stay away to
avoid burns or clothing ignition.
Young children should be carefully supervised when they are in the same room as the appliance.
Toddlers, young children, and others may be susceptible to accidental contact burns. A physical barrier is
recommended if there are at-risk individuals in the house. To restrict access to a replace or stove, install
an adjustable safety gate to keep toddlers, young children, and other at-risk individuals out of the room and
away from hot surfaces. Clothing or other ammable material should not be placed on or near the appliance.
Any grill, panel or door removed for servicing the unit must be replaced prior to operating. Failure to do so
may create a hazardous condition.
Installation and repair should be done by a qualied service person. The appliance should be inspected
before use and at least annually by a professional service person. More frequent cleaning may be required
due to excessive lint from carpeting, bedding material, etc. It is imperative that control compartments, burners
and circulating air passageways of the appliance be kept clean.
It is our policy that no responsibility is assumed by the Company or by any of its employees or representatives
for any damages caused by an inoperable, inadequate, or unsafe condition which is the result, either directly
or indirectly, of any improper operation or installation procedures.
This appliance must not be connected to a chimney ue serving a separate solid fuel burning appliance.
We recommend that our gas
hearth products be installed
and serviced by profession-
als who are certied in the
United States by the National
Fireplace Institute® (NFI) as
NFI Gas Specialists
Owners Information
35055.64-A
TCHF.22BODYA_ 280116-32
TCHF.22STBODYA
Caution
Safety

Owners Information
Important Note for the Commonwealth of Massachusetts
From Massachusetts Rules and Regulations 248 CMR 5.08:
(a) For all side wall horizontally vented gas fuelled equipment installed in every dwelling, building or structure used in whole or in part for residential
purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet
above nished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall be satised.
1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fuelled equipment, the
installing plumber or gas tter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is installed on the oor
level where the gas equipment is to be installed, in addition, the installing plumber or gas tter shall observe that a battery operated or hard-wired
carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served by the side wall horizontal
vented gas fuelled equipment. It shall be the responsibility of the property owner to secure the services of qualied licensed professionals for the
installation of hard-wired carbon monoxide detectors.
a. In the event that the side wall horizontally vented gas fuelled equipment is installed in a crawl space or an attic, the hard-wired carbon monoxide
detector with alarm and battery back-up may be installed on the next adjacent oor level.
b. In the event that the requirements of this subdivision cannot be met at the time of completion of installation, the owner shall have a period of thirty
(30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon monoxide
detector with an alarm shall be installed.
2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions shall
comply with NFPA 720 and be ANSI/UL 2034 listed as IAS certied.
3. SIGNAGE. A metal or plastic identication plate shall be permanently mounted to the exterior of the building at a minimum height of eight (8) feet
above grade directly in line with the exhaust vent terminal for the horizontally vented gas fuelled heating appliance or equipment. The sign shall
read, in print size no less than one-half (1/2) inch in size, “GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.
4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fuelled equipment shall not approve the installation unless,
upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5.089(2)
(a) 1 through 4.
(b) EXEMPTIONS. The following equipment is exempt from 248 CMR 5.089(2)(a) 1 through 4.
1. The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54 as adopted by the
Board; and
2. Product Approved side wall horizontal vented gas fuelled equipment installed in a room or structure separate from the dwelling, building or structure
used in whole or in part for residential purposes.
(c) MANUFACTURER REQUIREMENTS – GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product Approved side wall
horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the instructions provided
by the manufacturer for installation of the equipment and the venting system shall include:
1. Detailed instructions for the installation of the venting system design or the venting system components; and
2. A complete parts list for the venting system design or venting system.
(d) MANUFACTURER REQUIREMENTS – GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a Product Approved
side wall horizontally vented gas fuelled equipment does not provide the parts for venting the fuel gases, but identies “special venting systems”, the
following requirements shall be satised by the manufacturer.
1. The referenced “special venting system” instructions shall be included with the appliance or equipment installation instructions; and
2. The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a parts list and detailed
installation instructions.
(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fuelled equipment, all venting instructions, all parts
lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation.
4TCHF.22BODYA_ 280116-32
TCHF.22STBODYA
5055.64-A

Owners Information
55055.64-A
TCHF.22BODYA_ 280116-32
TCHF.22STBODYA
Specifications
• 22,000 BTU/hr input (xed input).
• Natural gas only.
• 24VAC honeywell direct ignition valve system.
• Power vented only. Either ush mounted power vent
(TCVT.PVFMA) or Surface mounted power vent (TCVT.
PVSMA) must be used. Vent extension kit (TCVT.PVEXTA)
contains 2 lengths of 25 foot exible venting pipe plus
adaptors. All of the above items are sold separately.
• 4” co-linear ex venting (1/4” clearance required).
• Multi exhaust position venting adaptors (1 position intake, 3
position exhaust).
• Helire 360 unit is all 304 stainless steel construction.
• Zero clearance unit (no non-combustible board required).
• One sided and two sided (see through) units available.
• Units t within a 2” x 6” stud wall.
• Two sided unit has outdoor ashing option.
Helifire 360 multi orientational helical flame fire feature.
Helifire 360 Specifications
Your zero-clearance Helire 360 re feature has been professionally installed by:
Dealer name: _____________________________________________
Phone Number: ___________________________________________
If you discover any problems with your Helire 360 re feature contact your dealer immediately to have the
unit repaired.
Caution: Do not attempt to repair the Helire 360 re feature because you may cause injury to yourself or oth-
ers, and risk causing damage to the unit.
Before operating your Helire 360 re feature carefully read this manual and pay close attention to all Safety
Warnings. The manual contains important information on the unit’s safe operation and maintenance.
Congratulations on your purchase
of a Town & Country Helifire 360 Feature
Figure 1: Helire 360.

Owners Information
6TCHF.22BODYA_ 280116-32
TCHF.22STBODYA
5055.64-A
Fire feature Dimensions
14 1/2”
90”
5 1/2”
60 1/8” 62 1/4”
Top down view
Front view Side view
5 1/2”
60 1/8” 62 1/4”
Side view
8 7/8”
8”
Top down view
8”
8 7/8”
One sided version Two sided version
Figure 2: Helire 360 dimensions.

Owners Information
The Helire 360 installation and venting must conform to the current CAN/CGA-B149 installation code (in
Canada) or the current National Fuel Gs Code, ANSI Z223.1 (in the USA), and approved per local codes.
Only qualied (licensed or trained) personnel should install this product.
In the state of Massachusetts, only a licensed Plumber and Gas Fitter may install this product.
In some jurisdictions, the Helire 360 may be installed in Manufactured Homes after the “rst sale”. Consult
local codes for approval. The Heater must be fastened in place.
Install in accordance with the current standard Mobile Homes, CAN/CSA Z240 MH (in CANADA), and the
Manufacturer’s Home Construction and Safety Standard, Title 24 CFR, Part 3280 or the current Standard
for Fire Safety Criteria for Manufactured Home Installations, Sites and Communities ANSI/NFPA 501A (in the
USA).
Warning: Turn off the Helire 360, and allow ample time for the unit to cool before proceeding.
Caution: The tempered glass is very fragile, and should be handled with care.
The Helire 360 door comes with a silicone seal and metal frame pre-assembled for easy mounting.
To replace a damaged door:
1. Remove the decorative trim from its magnetic holder.
2. Remove all 18 bolts from the door frame using the provided 5/32 Allen key. Be aware that the last bolt to
come out will allow the door frame to fall and keeping control of the door frame is crucial at this point.
3. Remove broken glass (if any) from the inside of the Helire 360.
4. Carefully position the replacement door frame against the Helire 360 and align the bolt holes.
5. Insert one bolt and then a second bolt on the opposite side of the frame in order to stabilize the frame.
Tighten them only nger tight at this point.
6. Insert the remaining bolts into the door frame. Tighten them only nger tight at this point.
7. Using the provided 5/32 Allen key (do not use a power driver), tighten the bolts so that the door frame
silicone seal is slightly compressed against the Helire 360 (about 1 1/2 turns past nger tight). Visually
inspect the door frame upon completion.
8. Return the decorative trim to its place on the Helire 360.
75055.64-A
TCHF.22BODYA_ 280116-32
TCHF.22STBODYA
Installation Requirements
Manufactured (Mobile) Homes
Door Frame Removal/Installation

Owners Information
NOTE: Fire feature may
take up to 30 seconds
to ignite each time the
“ON” button has been
selected
When lit for the rst time, the re feature may emit a slight odor for a couple of hours. This is due to the curing
of paints, sealants and lubricants used in the manufacturing process. This condition is temporary. Open
doors and windows to ventilate area. Odors caused by the curing process may cause discomfort to some
individuals. It is normal for replaces fabricated of steel to give off some expansion and/or contraction noises
during the start up or cool down cycle. Similar noises are heard from your furnace, heat exchanger or cook
stove oven.
In planning for
the installation of
the Helire 360,
it is necessary to
determine where the
unit is to be installed,
location of vent
system and where gas
supply piping may be
plumbed.
Various types of instal-
lations are possible,
such as, a penisula
wall, island, and
between two interior
walls.
8TCHF.22BODYA_ 280116-32
TCHF.22STBODYA
5055.64-A
First Fire
INSULATION
Special Operator Note
Locating the Helifire 360
Figure 3: Locating the Helire 360.

Owners Information
The Helire 360 is unique in that it can
be oriented in any position but must be
mounted so that the glass door is in a
vertical plane. The exception being that
the Helire 360 cannot be installed at in
a oor or ceiling. The following should
be considered before deciding on a nal
position.
• Flame length may vary by up to 30% due
to vent length and orientation.
• Vent exhaust pipe and air intake pipe
routing.
• Power vent terminal location.
Figure 4: Orientation options.
95055.64-A
TCHF.22BODYA_ 280116-32
TCHF.22STBODYA
Helifire 360 Orientation

Vent stand-offs are used to maintain a 1/4 inch space between combustible surfaces and the exhaust
portion of the exible venting material. The exible venting material may come into direct contact with non-
combustible material such as rockwool or cement board. See “Vent Stand-Offs” on page 22 for details.
Vent Stand-offs
Stud Supports
Installers Information Framing and Finishing
Note: The Helifire 360 should be in place and venting installed before framing in or building an
enclosure around the unit.
Because of the relatively low temperatures radiating from the Helire 360, clearances from combustible
framing and facing materials are not such an issue as it would be if a traditional replace were being installed.
For this reason, combustible materials can be installed up to and ush with the decorative trim. Only a total
thickness of 1/2 inch facing material may be used. If preferred, 1/2 inch drywall can be used when using the
ashing option (Figure 10).
NOTE:
The chase must be properly sealed at the ceiling level or
between floors in a multilevel installation. This is for fire-
stop purposes. See local building codes.
The finishing material must not interfere with glass frame access.
Stud supports for 2x6 studs are used to guide the exible venting from the re feature venting collar to the
power venting exhaust. See “Stud Supports” on page 25 for details
Installers Information
10 TCHF.22BODYA_ 280116-32
TCHF.22STBODYA
5055.64-A

Installers Information
14 1/2”
A
DETAIL A
SCALE 1 : 2
NAILING FLANGE
2x6 FRAME
The sides and top of the re
feature are framed in up to the
studs using conventional lumber.
Consult local building codes for
specic requirements.
Chase Insulation: When installing
the Helire 360 against a non-
insulated exterior wall or chase, it
is permissible to insulate any gap
between the Helire 360 and the
adjacent studs to same degree
as other exterior walls. Spray
insulation may be used right up to
the sides of the Helire 360 except
over the venting. If insulating
around venting, non-combustible
rockwool insulation must be used.
Cover the insulation and plastic
vapour barrier with a solid surface,
such as dry wall (sheet rock).
Consult local building codes.
8'0"
TCVT.814038A - 2x
TCVT.814038A
FLEX VENTING
FLEX VENTING
INTAKE EXHAUST
2 X 6 STUD
If insulating this area,
non-combustible
rockwool must be used.
Min.
8.5”
When installing the Helire 360
outdoors, the outdoor ashing
must be used. 7/16” sheathing
must be used under the
ashing(Figure 10).
When using outdoor flashing
Figure 5: Helire 360 Framing.
Figure 6: Example of 8 foot
ceiling installation.
11 5055.64-A
TCHF.22BODYA_ 280116-32
TCHF.22STBODYA

Installers Information
Framing Options
12 TCHF.22BODYA_ 280116-32
TCHF.22STBODYA
5055.64-A
Exhaust Intake
If insulating this area,
non-combustible rockwool
must be used.
Min.
8.5”
9’
Exhaust
Intake
If insulating this area,
non-combustible rockwool
must be used.
9’
Exhaust
Intake
If insulating this area,
non-combustible rockwool
must be used.
Figure 7: Horizontal framing option with vent through oor.
The Helire 360 may be framed
in either horizontally or vertically.
“Helire 360 Orientation” on page
9 for special note.
Figure 8: Through oor 9 foot ceiling framing option with
ame traveling downward.
Figure 9: Through oor 9 foot ceiling framing option with
ame traveling upward.
Exhaust vent pipe requires a
minimum 1/4 inch clearance to
combustible materials.
NOTE: There must be a mini-
mum space of 8 1/2 inches
between studs to be able to
accomdate the 90 degree
elbow at the intake (Figure 7).

Installers Information
10 3/8"
1 1/2"
2"
1/4" 1 1/4"
1/2" Maximum 14 1/2"
1/4" Strapping
Insulation
Outdoor ashing
House wrap
Tape
7/16" Maximum
Combustible or
non-combustible
facing material
Exterior
side
Interior
side
16 3/8”
10 3/8”
63 3/4”
3”
3”
1 1/2”
Front
3” 3”
69 3/4”
Figure 10: Outdoor flashing.
Figure 11: Helire 360 cross section view.
13 5055.64-A
TCHF.22BODYA_ 280116-32
TCHF.22STBODYA

Servicing of the Helire 360 can be performed from the side of the unit by removing the access panel from the unit.
Caution: The gas line should be installed by a qualied service person in accordance with all building codes. This
section is intended as a guide for qualied technicians installing this unit. Consult local and/or national building codes
before proceeding.
• GassupplylineconnectionislocatedontherearoftheHelire360.Gasconnectionacceptsa1/2”NPTtting.
Correct gas line diameter must be used to assure proper operation and pressure.
• TheHelire360inputpressureratingisshowninthetableonpage
“Helire 360 gas requirements.” on page 15.
NOTE: A sediment trap, as per national fuel gas code, must be installed in the gas supply line no more than 6 feet from
the gas control valve to minimize the possibility of any loose scale or dirt within the gas supply line from entering the
control valve.
Installers Information
Note: Verify gas pressures with the Helire 360 lit. Inlet pressure can be tested elsewhere before the Helire 360. The
instructions below are intended to test the manifold gas pressure. Manifold gas pressure must be tested with the Helire
360 “ON”.
1. Begin with the ON/OFF wall switch turned to the off position. Turn off the gas supply from inside the Helire 360. To
do this, the gas assembly needs to be pulled out of the Helire 360 body before being able to access the gas shut off
valve. The gas assembly is moved in toward the re box section of the body. An attached exible hose allows the
gas assembly to remain connected to the gas supply. Refer to instructions in Removing the Burner Control / Valve
assembly on page 16.
2. Locate the inlet and manifold test points on the Gas valve (Figure 13). After locating manifold test port, loosen and
remove the screw within the port using a 3/16 Allen wrench.
3. Attach a pressure gauge to the test port using an extension test tting. Attach a exible host to the barbed end of the
tting. Attach the other end of the exible hose to the gas pressure gauge.
4. Since the glass door has had to be removed for this test, the vacuum switch will need to be bypassed. Remove the
two purple wires from the vacuum switch.
5. Turn the Helire 360 gas valve to the ON position. Then, turn on the Helire 360 at the wall switch. Then, connect
the two purple wires to each other thereby by-passing the vacuum switch, and wait while the pre-purge procedure
nishes (about 10 seconds). This will be followed by ignition and lighting of the Helire 360. At this time, the manifold
pressure can be read from the pressure gauge display.
6. After testing is complete, turn off the gas supply, turn off the Helire 360 at the wall switch, and remove the pressure
gauges. Re-tighten the screws in the test ports using Thread Sealant. Re-attach the two purple wires to the vacuum
switch.
Gas Pressure Testing Procedure
Gas Connection
Gas Supply
GAS
CONNECTION
GAS ON/OFF
VALVE
INLET
TEST
PORT
MANIFOLD
TEST PORT
GAS
CONNECTION
Figure 12: Gas on-off valve. Figure 13: Gas valve assy.
14 TCHF.22BODYA_ 280116-32
TCHF.22STBODYA
5055.64-A

Gas Pressure Check
Gas pressure requirements
Input Pressure Natural Gas
Minimum 5.0”WC
Maximum 13.9” WC
Manifold Pressure
High 3.5”WC
Gas Output P.4.1
NG 2.2 mm 22,000 btu/hr 16.8%
Helifire360
Burner and Igniter
Compression ring
Figure 14: Helire 360 gas requirements.
Figure 15: Removing spark
igniter collar.
Figure 16: Spark igniter with its
ignition wire and ground wire.
Figure 17: Outer burner tube
fully seated.
Figure 18: Outer burner tube not
fully seated.
Installers Information
Note: To test the gas pressure, turn off the gas supply before removing the plug from the supply
pressure test port or manifold pressure test port. Verify gas pressures with the Helifire 360 lit.
The burner/igniter assembly consists of four main components: the valve tting, the 2.20 mm orice, the
outer burner tube with its sintered bronze insert and the spark igniter collar. The valve tting and the orice
both have compression rings which keep the orice and spark igniter collar in place while in an upside-down
position.
Accessing / replacing the orifice
1. Remove the spark igniter collar by pulling upward on the outside disk a
short distance (Figure 15) and disconnect the ignition wire from the igniter
(Figure 16). There will be some resistance because of the compression
ring holding the collar in place.
2. Remove the outer burner tube with its sintered bronze insert by gently
pulling it off of the orice and its compression ring.
3. Use a 1/2 inch socket wrench to remove the orice.
15 5055.64-A
TCHF.22BODYA_ 280116-32
TCHF.22STBODYA

Installers Information
Removing the Burner Control / Valve assembly
1. Remove burner / igniter assy as described
on page 12.
2. Remove the burner cover plate.
3. Remove two 5/32 inch Allen screws.
Figure 19: Spark igniter not fully seated
over compression ring.
Figure 20: Spark igniter fully seated
over compression ring.
Figure 21: Removing burner cover
plate.
Figure 22: Releasing gas valve assy
from main body.
Figure 23: Disonnecting 24VDC to
gas valve assy.
Figure 24: Gas ow on-off valve. Figure 25: Removing gas line.
4. Disconnect 24VDC molex connector to
the gas valve assy.
5. Turn gas ow valve off.
6. Disconnect the gas line to the gas valve
assy.
16 TCHF.22BODYA_ 280116-32
TCHF.22STBODYA
5055.64-A

Installers Information
CONTROL MODULE
MOLEX CONNECTOR
INLET GAS TEST POINT MANIFOLD GAS TEST
POINT
VENTING ADJUSTMENT
MAIN UNIT SWITCH
VACUUM SWITCH
GAS CONNECTION
TRANSFORMER
Figure 26: Removing gas valve assy. Figure 27: Gas valve assy.
Figure 28: Gas valve assy detail.
17 5055.64-A
TCHF.22BODYA_ 280116-32
TCHF.22STBODYA

LINE
NEUTRAL
GND
WHT GND
WHT
BK - BLACK
BRN - BROWN
GND - GROUND
GRY - GREY
WHT - WHITE
WHT
BK
GRY BK
BRN
BRN
BRN
BRN
GND
BK
Figure 29: Wiring instructions.
Installers Information
Electrical Connection
The Helire 360 requires
unswitched electrical power
supply. The re feature including
its power vent are rated at 115
Volts, 60 Hz, 2.48 amps.
• Connect electrical power
supply to the black and white
wires inside the electrical
connections compartment as
shown in Fig.
• Connect the ground wire
to the green wire inside the
compartment (Figure 29).
• Connect the Town and Country
On/Off wall switch (supplied) to
the two brown wires.
Helifire 360 electrical connection
Power vent electrical
connection
• Connect the black wire from
the power vent to the grey wire
inside the electrical connection
compartment.
• Connect the white wire from
the power vent to the white
wire inside the compartment.
• Connect the ground wire
to the green wire inside the
compartment.
18 TCHF.22BODYA_ 280116-32
TCHF.22STBODYA
5055.64-A

Wall Switch
Figure 30: Helire 360 wall switch.
Figure 31: Power vent grounding point
detail.
Figure 32: Power vent wiring.
Installers Information
The Helire 360 is controlled by a
standard wall switch which should be
installed by an electrician.
While the wall switch is included with
the Helire 360, the wiring for the wall
switch is not included .
In Canada, a thermostat can be
used for installations in a bed
room or a bed sitting room.
19 5055.64-A
TCHF.22BODYA_ 280116-32
TCHF.22STBODYA

Installers Information Electrical Diagram
POWER
VENT
NEUTRAL
LINE
24 VAC
TRANSFORMER
11 SPARK / SENSE
10 SENSE (NOT USED)
9 APS (VACUUM SWITCH)
8 (ON / OFF SWITCH) T-STAT
7 ALARM (NOT USED)
6 MV
5 120 VAC (LINE)
4 (POWER VENT) BLOWER
3 24 VAC
2 GND (BURNER)
1 GND (MV / 24 VAC)
MODULE
SENSE ELECTRODE
WHITE
GAS
VALVE
GND
VACUUM
SWITCH
115 VAC
60 Hz
Single phase
ON / OFF WALL SWITCH
(SUPPLIED)
BROWN
BROWN
BROWN
BLACK
BLUE
GREEN
ORANGE
GREEN
GREEN
GREEN
WHITE BLACK
BROWN
GREY
WHITE
BLACK
GREEN
BLACK
BLACK
PURPLE PURPLE
Figure 33: Helire 360 wiring diagram.
20 TCHF.22BODYA_ 280116-32
TCHF.22STBODYA
5055.64-A