Toyotomi EPH-121 User manual

EPH-121
INSTRUCTION MANUAL
CONTENTS
SHUTDOWN
ROUTINE MAINTENANCE
TROUBLESHOOTING
DEFECT ALARM
OPEN AND CLOSE THE PANELS
SPECIFICATIONS
···················································· 11
·································· 12
········································ 13
··············································· 13
························ 14
············································· 14
SAFETY PRECAUTIONS
NAME OF COMPONENT PARTS
HOW TO ASSEMBLE THE FRAME
OPEN AND CLOSE THE PANELS
OPERATION
TIMER OPERATION
······································ 1
···························· 5
························· 6
·························· 7
······················································· 9
··········································· 10
n
0
EPH-121-T.qxd 11.11.18 10:56 AM ページ b

●Do not put this heater
It causes the breakage
Using the broken powe
●Do not put any metals
heated air outlet open
When they touches the
a fire and an electrical
●Do not use this heater
this heater.
It causes falling and ca
breakage of the leg po
●Do not force to open t
It can result in the dam
will short out and it cau
●Do not move this heat
The product will slip ou
result in an injury.
●Do not let this heater o
It causes a fire and an
●Do not use a wire or a
It causes a breakdown
●If there is a possibility
power cord out of the
Depending on the degr
●Do not use this heater
accumulated.
It will catch fire and ca
●Do not use this heater
accumulated.
It will break a heater an
●Do not put spray cans
carbonated drinks aro
Cans pressure will be g
and a fire.
SAFETY PRECAUTIONS (Please read carefully and follow all instructions.)
¡Items shown here are labeled “ Warning!” and “ Caution!”
Be sure to follow the warnings and cautions as they explain important details regarding safety.
Improper use can cause death or serious personal injury.
Improper use can cause personal injury or physical damage.
¡Be sure to follow the advice in the instruction manual in order to use this unit properly.
WARNING
CAUTION
Caution Must be
performed.
Remove the power plug
from the electric outlet.
Do not
disassemble.
1
WARNING
●No other current than AC 220V/230V is allowed to be used.
When used on anything other than 220V/230V mains, fire or electric shock
may occur.
●Do not allow children, disabled and elderly to use this product wihtout
any attendant.
It can result in a scald injury.
●Remove all dust and dirt from the power plug and insert it completely
into the outlet to ensure proper contact.
Dust and dirt on the plug or incomplete insertion creates the danger of
electrical shock and fire.
●Do not leave this heater on when you leave home.
It causes a fire.
●Do not let this heater running by using an extension cord from the wall
outlet and do not share the outlet with other appliances.
It causes a fire, an electrical shock and a heat generation of the plug.
●Do not damage, break, modify, forcibly bend, yank, twist, or bundle the
power cord.
A fire or electric shock may result if the cord is pinched or modified, or
something heavy is placed on it.
●When an internal wall outlet has two outlets or more, use this outlet for
this heater alone. Check if your wall outlet is for 220V/230V and 7A or
more and do not share the wall outlet with other appliances.
Electrical power capacity of the interior wiring (wiring inside the wall) will
exceed the acceptable range. It causes a fire, an electrical shock and a
heat generation of the plug.
EPH-121-T.qxd 11.11.18 10:56 AM ページ 1

2
WARNING
●Do not put this heater over the power cord.
It causes the breakage of the power cord.
Using the broken power cord causes a fire and an electrical shock.
●Do not put any metals (example: pins or needles) or your finger in the
heated air outlet opening or the air inlet.
When they touches the inside, anomalous heating will occur and it causes
a fire and an electrical shock and it can result in a scald injury.
●Do not use this heater as a step ladder and do not sit on or lean against
this heater.
It causes falling and can result in an injury. And also it can result in
breakage of the leg portion or the damage of this heater.
●Do not force to open this heater wide.
It can result in the damage of this heater and the wires inside the product
will short out and it causes an electrical shock.
●Do not move this heater with the panels left open wide
The product will slip out of your hands and it causes damages and can
result in an injury.
●Do not let this heater off by plugging in or pulling out the power plug.
It causes a fire and an electrical shock.
●Do not use a wire or a copper wire as a cutout switch fuse.
It causes a breakdown and a fire.
●If there is a possibility of lightning strike, turn off the heater and pull the
power cord out of the wall outlet.
Depending on the degree of lightning strike, it causes a breakdown.
●Do not use this heater in the place where flammable gas is produced or
accumulated.
It will catch fire and causes a fire.
●Do not use this heater in the place where corrosive gas is produced or
accumulated.
It will break a heater and cables and may cause a breakdown.
●Do not put spray cans, cartridges for a portable gas stove and
carbonated drinks around or near this heater.
Cans pressure will be getting higher by heat, and it causes an explosion
and a fire.
)
EPH-121-T.qxd 11.11.18 10:56 AM ページ 2

●Do not use this heater
The product will tip ove
●Do not use this heater
Your pets may break th
●The Panel heater is no
bathroom.
An electric shock or m
●In the early stage of u
compound will be pro
sufficiently.
The odor will be lesser
●Do not put clothes or
front panels of the pro
of (in a radiation direc
It causes a fire and a
between the product a
●Use this heater by ke
described on the right
body and the flamm
side or the other side
wall or the furniture.
When this heater is left
in the microcomputer. A
However when this he
deleted.
Temperature will be au
the mica-heater is swit
is not defect.
Because this heater i
appliance or with the
overheat protection sy
causes and let the pr
activates after removin
bought the product.
3
WARNING
●Do not spray with insecticides.
It causes change in color and crack.
●Do not use this heater near flammable items such as futons, blankets
and curtains.
It causes a fire.
CAUTION
●When unplugging the power plug, grip the plug and not the cord. .
Do not pull the cord or the wire inside the cord will be damaged resulting
in heat or ignition.
●If the Panel Heater is not used for a long time, remove the power plug
from the outlet.
Caked-on dust may cause heat or ignition.
●No damaged power cord, plug, or loose plug connection is allowed to
be used.
An electric shock, short, or inflammation may otherwise be caused.
●Do not use this heater in an empty room where no one is such as glass
houses and animal rooms.
It may cause unexpected accident.
●Only authorized technicians should disassemble, repair, or modify this
product.
It causes a fire, electrical shock or injury.
●Do not touch the heater body and the hot portion such as guarding part
while the heater is running or immediately after being turned off.
It can result in a scald injury.
Especially pay attention to your children.
●Do not use this heater to dry clothes and for other purpose.
(example: for industrial and business purpose)
It causes change in body shape and a fire from over heat.
●Do not install the Panel heater on an unstable floor, shelf or wall.
There is a fear of the Panel heater falling down.
●Do not use this heater on the thick-piled carpet.
It can result in injury from falling and causes change in carpet color and
dent.
EPH-121-T.qxd 11.11.18 10:56 AM ページ 3

4
More
than
30cm
More than 100cm
More than 100cm
More
than
30cm
●Do not use this heater without the frame.
The product will tip over and it can result in an injury.
●Do not use this heater to warm your pets such as dogs and cats.
Your pets may break the body or power cord and it causes a fire.
●The Panel heater is not allowed to be used in such a moist place as a
bathroom.
An electric shock or malfunction may occur.
●In the early stage of use, volatile organic compound and carbonyl
compound will be produced and it will smell. In that case let fresh air in
sufficiently.
The odor will be lesser by continuing to use of this heater.
●Do not put clothes or something foreign materials between
front panels of the product and do not put something in front
of (in a radiation direction) the front panels.
It causes a fire and a breakdown. Keep the isolation distance
between the product and the flammables.
●Use this heater by keeping each distance
described on the right between the product
body and the flammables. However one
side or the other side shall not face to the
wall or the furniture.
CAUTION
When this heater is left plugged in and turned on or off, the previous turn-off information is stored
in the microcomputer. And when this heater is turned on again, it runs with that information stored.
However when this heater is unplugged, the information stored in the microcomputer will be
deleted.
Temperature will be automatically controlled so the cricking sound will be made every time when
the mica-heater is switched on or off. It is the sound to switch on or off inside the controller and it
is not defect.
Because this heater is used in the room where get hot easily or affected by other heating
appliance or with the opening for the ventilation blocked, if inside the body is overheated, the
overheat protection system will work and stop all operations. In that case, remove the overheat
causes and let the product cool first, then run it again. If the overheat protection system still
activates after removing the causes and all operations are stopped, contact the shop where you
bought the product.
INFORMATION
EPH-121-T.qxd 11.11.18 10:56 AM ページ 4

1. Keep the heater
unit down on the
cloth. (Fig. 1)
2. Assemble the fra
the frame suppor
(Fig. 2)
3. Fix the frame and
nut tightly. (Fig. 3
4 Turn the heate
down and asse
frame to the l
Wing nut the sam
the above. (Fig. 1
Do n
asse
5. Set up the heater
CAUTION
HOW TO AS
Power plug
5
NAME OF COMPONENT PARTS
(Back side)
Frame (2 pcs.) Wing nut (4 pcs.) Frame support (4 pcs.)
Appearance
Accessories
Operation panel
Surface temperature
sensor
(Built in the unit)
Heated
air outlet
Guard
Front panel
High limit switch
Operation panel
Tip over switch
(Built in the unit)
Power lamp
Operation switch
(ON/OFF)
Panel operation
lamp
Temperature lamp
Timer lamp
Temperature
select switch
OFF timer switch
ON timer switch
ON timer lamp
Panel select switch
Power supply cord
Frame
Rear panel
Air inlet
(Front side)
Leg
OFF timer lamp
Room temperature sensor
(Built in the unit)
EPH-121-T.qxd 11.11.18 10:56 AM ページ 5

6
1. Keep the heater closed position and lay the
unit down on the stable table spread the soft
cloth. (Fig. 1)
2. Assemble the frames to the legs and attach
the frame supports on right and left side.
(Fig. 2)
3. Fix the frame and frame support with Wing
nut tightly. (Fig. 3)
4 Turn the heater upside
down and assemble the
frame to the legs with
Wing nut the same way as
the above. (Fig. 1-3)
Do not insert the plug in electrical outlet before completing
assembling.
5. Set up the heater carefully and be sure that the frames are fixed firmly.
Frame
Frame
support
(Fig. 2)
(Fig. 3)
(Fig. 1)
Wing nut
Soft cloth
CAUTION
HOW TO ASSEMBLE THE FRAME
)
p
ch
EPH-121-T.qxd 11.11.18 10:56 AM ページ 6

NOTE
Room tempe
room tempe
NOTE
Set tempera
1Insert the plug in electr
2Press the Operation sw
Power lamp, Panel ope
lit.
3Press the Temperature
temperature setting.
The heater will be tu
temperature reaches se
The heater will be tu
temperature exceeds t
the room temperature
0.5˚C, the heater will b
desired temperature.
When the heater is turn
Panel select switch can
4Press the Panel select s
Panel operation lamp w
repeatedly.
[R]: Right panel is opera
[L]: Left panel is operat
[LR]: Both left and right
5Press the Operation sw
Power lamp, Panel ope
off.
6Be sure that Power lam
the heater.
[high] ⇒[mid. H] ⇒
OPERATION
7
INFORMATION
This product is built to be run with the range from closed position (0 degree) to opened position (155
degrees). Hold both ends of the panels securely as described above, and open or close slowly.
Closed condition Opened condition
Closed condition Opened condition
Parallel
155˚ More than 155˚
Parallel
Do not open the panel forcibly to avoid the damage of the heater or
breaking of wire.
WARNING
Lift the front sides of the product a little (approx. 5cm), and open the
panel with the hinge segment centered, so you can open the panels
smoothly.
Do not open and close the panels during operation
and be careful not to touch the heated part such as
surface of the panel and heated air outlet.
CAUTION
OPEN AND CLOSE THE PANELS
EPH-121-T.qxd 11.11.18 10:56 AM ページ 7

8
Power lamp
Operation
(ON/OFF)
switch
Panel operation
lamp
Panel select
switch
Temperature
amp
Timer
lamp
Temperature
select switch
OFF timer switch
ON timer switch
OFF timer lamp
ON timer lamp
NOTE
Room temperature display may not indicate the true
room temperature depending on the usage environment.
NOTE
Set temperature: [ high ] = approximately 30˚C
[ mid.H ] = approximately 26˚C
[ mid.L ] = approximately 22˚C
[ low ] = approximately 18˚C
1Insert the plug in electrical outlet.
2Press the Operation switch.
Power lamp, Panel operation lamp and Temperature lamp will be
lit.
3Press the Temperature select switch to choose your desired
temperature setting.
The heater will be turned on and off automatically when the
temperature reaches set temperature.
The heater will be turned off automatically when the Room
temperature exceeds the selected setting by approx. 1.5˚C. When
the room temperature drops the selected setting by approx.
0.5˚C, the heater will be turned on automatically to maintain the
desired temperature.
When the heater is turned off, Panel operation lamp will go off and
Panel select switch cannot be used.
4Press the Panel select switch to select the panel operation.
Panel operation lamp will be changed
repeatedly.
[R]: Right panel is operated when opened position.
[L]: Left panel is operated when opened position.
[LR]: Both left and right panels are operated
5Press the Operation switch to turn the unit off.
Power lamp, Panel operation lamp and Temperature lamp will go
off.
6Be sure that Power lamp goes off before unplugging after using
the heater.
[high] ⇒[mid. H] ⇒[mid. L] ⇒[low]
[R] ⇒[L] ⇒[LR]
3
4
25
OPERATION
5
EPH-121-T.qxd 11.11.18 10:56 AM ページ 8

The ON timer
switch even if i
If you wish to
switch until ON
Your heater ca
Temperature se
NOTE
You can set the ON timer
pressing the ON timer swi
During operation
1Press the ON timer swi
Your heater will stop t
condition for ON timer
ON timer lamp will be
2Press the ON timer sw
is blinking.
Timer lamp will be lit
repeatedly.
ON timer lamp will be
ON timer function is se
3Power lamp, ON time
heater will turn on at th
During operation
1Press the ON timer swi
ON timer lamp will be b
2Press the ON timer sw
is blinking.
Timer lamp will be lit
repeatedly.
ON timer lamp will be
ON timer function is se
3Power lamp, ON time
heater will turn on at th
1Press the Operation sw
Operation lamp, Panel op
2Be sure that the Power
3Pull out the Power plug
The ON timer
switch even if
If you wish to
switch until ON
Your heater can
Temperature se
NOTE
ON TIMER
SHUTDOWN
9
[1(h)] ⇒[2(h)] ⇒[4(h)] ⇒[8(h)]
[cancel]
EPH-121 is equipped ON and OFF timer function, but
could not be set ON and OFF timer at the same time.
The latest set timer (ON or OFF) will be given preference.
NOTE
The OFF timer can be changed by pressing OFF timer
switch even if it is set completely.
If you wish to cancel the OFF timer, press the OFF timer
switch until OFF timer lamp goes off.
NOTE
NOTE
The OFF timer can be changed by pressing OFF timer
switch even if it is set completely.
If you wish to cancel the OFF timer, press the OFF timer
switch until OFF timer lamp goes off.
Power lamp
Operation
(ON/OFF)
switch
Panel operation
lamp
Panel select
switch
Temperature
amp
Timer
lamp
Temperature
select switch
OFF timer switch
ON timer switch
You can set the OFF timer to turn off automatically at the set time by
pressing the OFF timer switch during operation and shutdown.
During operation
1Press the OFF timer switch during operation.
OFF timer lamp will be blinking for a few seconds.
2Press the OFF timer switch to select the timer when OFF timer
lamp is blinking.
Timer lamp will be lit
repeatedly.
OFF timer lamp will be lit after blinking for a few seconds and the
OFF timer function is set completely.
3The heater will shut down the operation at the set time. All lamps
will go off.
During shutdown
1Press the OFF timer switch during shutdown.
Your heater will be turned on and start the heating operation.
OFF timer lamp will be blinking for a few seconds.
2Press the OFF timer switch to select the time when OFF timer
lamp is blinking.
Timer lamp will be lit
repeatedly.
OFF timer lamp will be lit after blinking for a few seconds and the
OFF timer function is set completely.
3The heater will shut down the operation at the set time. All lamps
will go off.
[1(h)] ⇒[2(h)] ⇒[4(h)] ⇒[8(h)]
[cancel]
12
OFF TIMER
TIMER OPERATION
EPH-121-T.qxd 11.11.18 10:56 AM ページ 9