Toyotomi Zibro LC-135 User manual

LC – 135
GB OPERATING MANUAL ............................. PAGE 2
D GEBRAUCHSANWEISUNG............................PAGE 18
F MANUAL D’UTILISATION ........................... PAGE 36
NL GEBRUIKSAANWIJZING .............................PAGE 54
E INSTRUCCIONES DE USO ............................PAGE 70
I ISTRUZIONI D’USO .................................PAGE 86
DK BRUGERVEJLEDNING ...............................PAGE 102
N BRUKERINSTRUKSEN ...............................PAGE118
S INSTRUKTIONERNA INNAN ANVANDNING..............PAGE 134
FIN KÄYTTÖOHJEET ...................................PAGE 150

Thank you for choosing a “TOYOTOMI” product!
Toyotomi products are used by satisfied customers worldwide. In order to
assure the comfortable and safe use of our products by customers in each
country, our products conform to the safety standards not only in Japan but
also in every country around the world we do business with.
Toyotomi tailors its products to satisfy its customer’s needs by always pursuing
our business philosophy, “sharing joys in daily living”. We will continue to
research, develop and manufacture products that match people’s lifestyle for
efficiency, safety and comfort.
We hope that you’ll enjoy your Toyotomi appliance for years to come!
We invite you to read this instruction manual first, to ensure the maximum
lifetime for this appliance.
Get to know us better…visit us at www.toyotomi.eu for our full line of
products.
1 READ THE DIRECTIONS FOR USE FIRST.
2 IN CASE OF ANY DOUBT, CONTACT YOUR DEALER.
3 BEFORE YOU START READING, CONSULT THE MAIN COMPONENTS LIST ON THE LAST PAGE.
4
2

GENERAL DIRECTIONS FOR USE
Below you will find the main steps to be taken for
using your heater. For more details, please refer to
the MANUAL.
Remove all packaging materials (Fig. A).
Fill the removable tank 쐆(refer to Section B, Fig. D).
Insert the plug into the wall-socket.
Ignite the heater using the key 씈(refer to Section D).
If required, change the temperature using the adjustment keys
(refer to Section E).
Switch off the heater by pressing the key 씈.
1
2
3
4
5
6
s As a fire precaution, the tank must be filled either when the heater has been
switched off or in another room than the room where the heater is installed.
s Always ensure that the tank is closed properly after filling it at a safe distance from
all sources of heat and open flames (see Section B).
s The first time the heater is ignited it will smell like “new” for a short time.
s Store all fuel containers with their original caps and seals in a cool and dark place.
s Fuel ages. Use new fuel at the start of every heating season.
s Only use high quality and water -free pure paraffin in accordance with local
legislation.
s Before changing brands and/or types of fuel make sure that the mobile heater first
completely empties all of the remaining fuel inside the heater.
4
3

WHAT YOU NEED TO KNOW IN ADVANCE
ALWAYS MAKE SURE THAT THERE IS SUFFICIENT VENTILATION
Read this user manual carefully before using the appliance and keep it for future
reference. Install this device only when it complies with local/national legislation,
ordinances and standards. This product is intended to be used as a heater in
residential houses and is only suitable for use in dry locations, in normal household
conditions, indoors in living room, kitchen and garage.
Note: To avoid unexpected shut off, we recommend to put a door or window ajar
when the heater is operating.
Regardless of the model, you must always make sure that the heater is used in
a room large enough to enable the heater to be used safely without extra
ventilation. If the room is smaller than required, you must always open a door or
window slightly (ensuring an opening of approx. 2.5 cm). It is important that every
room where the heater is used has sufficient air intake and efficient air outflow
(both openings must have a minimum cross section of 50 cm2). No modifications
to the safety system are allowed, as that will invalidate the guarantee that the air
probe will work properly. Consult your dealer in case of doubt.
Especially for France: Your heater was designed to operate exclusively on fuel for
liquid fuel-operated mobile heaters in accordance with the Decrees of 18-07-2002
and 25-06-2010. The use of other fuels is forbidden. Ask your dealer or check our
website for the addresses of our retailers. The liquid fuel-operated mobile heater
is intended as an extra heater, and not as a continuous source of heat.
Especially for United Kingdom: Only use Class C1 paraffin fuel in accordance with
BS2869; Part 2, or equivalent.
The user must comply with the following instructions for proper use:
DO NOT
- use the liquid fuel-operated mobile heater in caravans, boats, and vehicle
cabins;
- use the liquid fuel-operated mobile heater in insufficiently ventilated rooms
(consult the table of properties for the minimum dimensions of the room to
be heated), underground rooms and / or at a height of over 1500 metres;
- modify the heater safety features.
The use of this type of heating in public rooms is subject to prior regulatory
permission. Obtain proper information on this in advance.
4
4

THE RIGHT FUEL
Your heater has been designed for use with high-quality water-free pure paraffin
oil. Only fuels of this kind will ensure clean and proper burning. Lower quality fuel
may result in:
increased possibility of malfunctioning
incomplete burning
reduced heater lifetime
smoke and/or smells
deposits on the grid or mantle
Using the right fuel is therefore essential for safe, efficient, and comfortable use
of your heater.
Damage and/or malfunctions of the heater due to the use of other than high
quality water-free pure paraffin oil is not covered by the warranty.
Always refer to your local dealer for the right fuel for your heater.
MANUAL
AINSTALLING THE HEATER
1Carefully remove your heater from the box and check the contents.
In addition to the heater you also need to have:
a manual fuel pump
 a transportation cap
 these directions for use
Keep the box and the packaging materials (Fig. A) for storage and/or
transportation.
2Open the lid of the removable tank 쐏and remove the piece of cardboard.
3Fill the removable tank as indicated in Section B.
4The floor should be firm and completely level. Reposition the heater, when it
is not level. Do not try to correct the situation by placing books or other
goods under the heater.
A
4
5
This transportation cap
is packed separately in
the box. Only this cap
ensures trouble-free
transportation of the
heater after use.
Store it well!
Only the use of the
correct fuel will ensure
safe, efficient, and
comfortable use of your
heater.

5Insert the plug 쐈into the wall-socket (230 Volts - AC / 50 Hz) and set the
correct time using the adjustment keys 씊(refer to Section C).
6Your heater is now ready for use.
BFILLING FUEL
Fill the removable tank in a suitable place since there can always be some spillage.
Follow the procedure below:
1Make sure that the heater is switched off.
2Open the upper lid and lift the removable tank out of the heater (Fig. B).
Note: Some drops may leak from the tank. Put down the removable tank (cap
pointing upwards, handle on floor (Fig. C) and screw off the fuel cap.
3Fill the removable tank using a fuel pump (refer to fuel pump operation
instructions.) Make sure that it is in a higher position than the removable tank
(Fig. D). Insert the ribbed hose into the opening of the removable tank.
4Check the removable tank fuel gauge while filling the tank (Fig. E). Stop filling
once the gauge indicates that the tank is full. Never overfill the tank,
especially not when the fuel is very cold (fuel expands when it heats up).
5Check whether the fuel cap is straight and tightened properly. Reinstall the
removable tank in the heater (cap down). Close the lid.
CSETTING THE CLOCK
It is only possible to set the correct time and day, when the heater is connected to
the mains and not burning. Use the adjustment keys 씊to set the time and day/set
(weektimer) 씎to set the day.
First press one of the three keys to switch on the function (the 4-digit 쐉will start
blinking). Next, set the hours using the key (쑼hour) and the minutes using the
key (쑿min.) and the day using the key extension day/set 씎.
Press once to increase the value by one step. When you hold down the key, the
value will continue going up, until you release the key again. After approximately
10 seconds the 4-digit will stop blinking and the setting will be locked&Dge,D'.
5 minutes after switching off the heater, the information on the display will
disappear and the heater will automatically switch into the stand-by position.
When the heater has been unplugged for more than 30 minutes (or after a power
failure), the time and the day need to be set again.
4
6
F: When the 4-digit stops
blinking, the setting
has been locked to the
indicated value.
D
C
B
E
empty full
!

D IGNITING THE HEATER
When used for the first time, a new heater may give out a smell for a short while.
You should therefore provide extra ventilation.
Always ignite the heater with the button
씈 . Never use matches or a cigarette
lighter. Just press the button
씈 to ignite the heater.
The button will start blinking, indicating that the ignition procedure has started.
This will take a short while. Once the heater is burning, the button
씈 will
remain lit (red). The information display
쐉 will show two numbers (Fig. G). The
actual room temperature is indicated below ROOM, while the temperature setting
is indicated below SET. The latter can be changed with the adjustment keys (refer
to Section E).
Prior to igniting the heater, always check for sufficient fuel in the removable tank.
ESETTING THE REQUIRED TEMPERATURE
The temperature setting can only be adjusted, when the heater is burning. Use
the adjustment keys 씊to adjust the temperature. First press either of the two
keys to switch on the function (the °C mark and 4-digit 쐉will start blinking). Next,
adjust the temperature using the key (쑿min.) to set the temperature to a higher
setting and the key (쑼hour) to lower the temperature. Press once to increase the
value one step. After approximately 10 seconds the °C mark and 4-digit will stop
blinking and the setting will be locked (Fig. F).
The available temperature settings range from 6°C minimum to 28°C maximum.
When the heater has been unplugged for more than 10 minutes (or after a power
failure), the temperature will reset to the factory setting of 20°C.
FSWITCHING OFF THE HEATER
There are two ways to switch off the heater.
1Press the button 씈. The information display will show the CLOCK signal.
Within approximately one minute the flame will have extinguished.
2Press the TIMER key 씋, when you want to switch off the heater and ignite it
again with the timer the next time. This not only switches off the heater, but
it also activates the timer function.
GTHE INFORMATION DISPLAY
The information display 쐉 not only serves as an indicator of the (set) time and
temperature (Sections C, E, and F), it also indicates any malfunctioning of the
heater. The code on the information display tells you what is the matter:
CODE INFORMATION WHAT TO DO
e - 0 Temperature within the heater too high. Cool-down and re-ignite.
f - 0 Power interrupted. Re-ignite the heater.
e - 1 Faulty thermostat. Contact your dealer.
f - 1 Faulty burner thermistor. Contact your dealer.
e - 2 Starting problems. Contact your dealer.
e - 5 Tipping-over protection. Re-ignite the heater.
e - 6 Poor burning. Contact your dealer.
e - 7 Room temperature If necessary,
above 32°C. re-ignite the heater. 4
7
G: The required
temperature on the
left, the measured
temperature on the right.
In case of any
malfunctioning the
information display
will tell you what is the
matter.

e - 8 Defective booster. Contact your dealer.
e - 9 Air filter dirty; or Clean filter
Fuel pump dirty. Contact your dealer.
The heater has been in operation
continuously for a period of 69 hours
and has turned itself off automatically. Switch the heater back on.
-- : --
+
Out of fuel. Refill removable tank.
-- : -- + Too little ventilation. Ventilate better.
Always contact your dealer for any malfunctioning not listed above.
AUTOMATIC DEACTIVATION
This heater is fitted with a safety system that ensures that it switches off
automatically after 69 hours continuous operation. The following will then appear
in the display: . If desired, you can switch the heater on again by pressing
the button 씈(see Section D).
AUTOMATIC CLEANING MODE
When the heater has been burning continuously for two hours at its highest
setting, the burner will automatically start an autoclean procedure. The display
will show the autocleaning code cl:05 running back to cl:01. The procedure takes 5
minutes, during which the heater will burn at its lowest setting, while the burner
autocleans. When the burner is clean again, the heater will automatically switch
back to the highest setting again.
HCHILDPROOF LOCK
The childproof lock can be used to prevent children accidentally changing the
heater settings. When the heater is burning and the childproof lock is on, the
heater can only be switched off. Other functions are blocked then. If the heater
has already been switched off, the childproof lock also prevents accidental ignition
of the heater. Activate the childproof lock by pressing the appropriate key
씉
and holding it down for more than 3 seconds. The KEY-LOCK indicator ( ) will
appear on the information display (Fig. H), indicating that the childproof lock has
been activated. Switch off the childproof lock by pressing the key
씉 and holding it
down for more than 3 seconds once again.
4
8
H: When the mark
appears, the childproof
lock has been activated.

ITHE CORRECT USE OF ‘SAVE’
The ‘SAVE’ function allows you to limit the temperature. When this function is
activated, the heater will automatically switch off, when the room temperature
exceeds the set temperature by 3°C. Subsequently, when the room temperature
has dropped again to the set temperature, the heater will automatically switch on
again.
Activate the ‘SAVE’ setting by pressing the appropriate 씌key. will display on
the information display (Fig. I). Switch off the function by pressing the SAVE key
once again.
Without the ‘SAVE’ setting your heater will maintain the set temperature by
approximation as well, by adjusting its heating capacity. ‘SAVE’ is an economy
setting, which you can use when, for instance, you are not present in the room or
to keep it frost-free.
JTHE ‘FUEL’ INDICATOR
When the FUEL indicator appears, it means that there is only fuel left for 10
more minutes. The count-down of the remaining heating time can be seen in the
information display 쐉(Fig. J). Now you have two options:
You remove the fuel tank and refill it outside the living room (section B) or
You push the button extension 씎. By pushing this button, the remaining
heating time will extend to 90 minutes.
The heater will automatically switch back to its lowest position. In the display
the number 90 will appear, which will decline to 10. At the arrival of 10,
you will hear an alarm signal every two minutes, warning you to refill the
removable tank. If you do not react, the heater will extinguish by itself. The
heater will also sound a warning signal, when it switches off. The fuel
indicator will blink, while four lines (--:--) are blinking in the information
display. You can stop this by pressing the button 씈once more.
Once the heater has used up all its fuel and extinguished, it will take some time,
after the refill, before the heater is completely ready for use again.
KTHE ‘VENT’ INDICATOR
When the VENT indicator starts blinking, this is a sign that the room is not vented suf-
ficiently (Fig. K). The heater will switch off automatically. If the indicator continues
blinking after extra ventilation, please contact your dealer.
4
9
I: When the SAVE
function is activated, the
heater will automatically
switch on or off in
order to remain within
a specified temperature
range.
J: When the FUEL
indicator has appeard,
the information display
will show the number of
minutes of fuel left in
the tank.
K: A blinking VENT
indicator light is a sign
that you need extra
ventilation.
!

LMAINTENANCE
Switch off the heater and let it cool down, before you start any maintenance
work. Also disconnect the plug from the mains. Your heater needs hardly any
maintenance. It is, however, important that you clean the air filter 쐊and the
vent filter 쐎with a vacuum cleaner and the grid 쐇with a damp cloth, both on a
weekly basis. Remove the air filter cap occasionally (Fig. L) and clean it with soapy
water. Prior to reinstallation, make sure that the air filter cap has fully dried.
Regularly inspect the fuel filter as well:
1Remove the removable tank 쐆from the heater and remove the fuel filter
(Fig. M). Some drops may leak from the filter; keep a cloth at hand.
2Remove the dirt by tapping the fuel filter upside-down against a hard surface.
(Never clean it with water!)
3Reinstall the fuel filter into the heater.
We recommend that you remove dust and stains in time with a damp cloth,
because otherwise these may cause stains that are hard to remove.
Do not remove any heater components yourself. Always contact your dealer
for repairs. When the power cord is damaged, it may only be replaced by an
authorised fitter. Use a new cord of the type H05 VV-F.
MSTORAGE (END OF THE HEATING SEASON)
At the end of the heating season, you must store the heater in a dust-free place,
if possible in its original packaging. Unused fuel cannot be used in the next
heating season. We therefore recommend that you burn up all fuel. If there is
still some fuel left, do not throw it away, but dispose of it in accordance with the
local regulations for the disposal of domestic chemical waste. Always start the
new heating season with fresh fuel. When you start re-using the heater follow the
instructions again (starting from section A and as specified).
NTRANSPORTATION
Take the following measures to avoid fuel leakage during the transportation of
the heater:
1Let the heater cool down.
2Remove the removable tank 쐆from the heater and remove the fuel filter
(refer to Section L, Fig. M). Some drops may leak from the filter; keep a cloth
at hand. Store the fuel filter and the removable tank outside the heater.
3Place the transportation cap into the position of the fuel filter (Fig. N).
Press it tight. The transportation cap will, as much as possible, prevent oil
leakage from the heater during transport.
4Always move the heater in an upright position.
5Make the fixed tank empty with a fuel pump before transportation or in case
of wrong or dirty fuel. First remove the fuel filter and then insert the fuel
pump into the empty fixed tank. Follow the same procedure if the fuel tank
contains water.
4
10
Fuel filter
M
transportation
cap
N
L
!