TP-Link TD-8810 User manual

TD-8810
External ADSL2+ Router
Rev: 1.1.2
1910010007

II
COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a registered trademark of
TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or
registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used to make any
derivative such as translation, transformation, or adaptation without permission from TP-LINK
TECHNOLOGIES CO., LTD. Copyright © 2008 TP-LINK TECHNOLOGIES CO., LTD.
All rights reserved.
http://www.tp-link.com

III
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may
cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
EC DECLARATION OF CONFORMITY (EUROPE)
In compliance with the EMC Directive 89/336/EEC, Low Voltage Directive 73/23/EEC, this product
meets the requirements of the following standards:
• EN55022
• EN55024
• EN60950
SAFETY NOTICES
Caution:
Do not use this product near water, for example, in a wet basement or near a swimming pool.

IV
Package Contents
The following items should be found in your package:
¾One TD-8810 External ADSL2+ Router
¾One AC power Adapter for TD-8810 External ADSL2+ Router
¾One Resource CD for TD-8810 External ADSL2+ Router, including:
•This Guide
•Quick installation Guide Program
•Other Helpful Information
¾Quick installation Guide
¾One RJ45 cable
¾Two RJ11 cable
¾One ADSL splitter
)Note:
Make sure that the box contains the above items. If any of the listed items are damaged or
missing, please contact with your distributor.

V
CONTENTS
Chapter 1. Introduction ........................................................................................1
1.1 Product Overview...................................................................................................... 1
1.2 Main Features ........................................................................................................... 1
1.3 Supporting protocol................................................................................................... 1
1.4 Transmit data-rate..................................................................................................... 2
1.5 ATM property ............................................................................................................ 2
1.6 System support ......................................................................................................... 2
1.7 Working environment ................................................................................................ 2
1.8 Conventions .............................................................................................................. 2
Chapter 2. Hardware Installation.........................................................................4
2.1 System requirement.................................................................................................. 4
2.1.1 LED explanation...............................................................................................................4
2.2 Rear-panel ................................................................................................................4
2.3 Hardware installation procedures.............................................................................. 5
Chapter 3. System Configuration........................................................................6
3.1 Computer Configuration............................................................................................ 6
3.2 Login .........................................................................................................................7
3.3 Quick Setup............................................................................................................... 8
3.3.1 PPPoA..............................................................................................................................9
3.3.2 PPPoE............................................................................................................................11
3.3.3 MER................................................................................................................................13
3.3.4 IPoA................................................................................................................................15
3.3.5 Bridging ..........................................................................................................................17
3.4 Change Password................................................................................................... 18
3.5 Web Setup .............................................................................................................. 19
3.5.1 DHCP IP Reservation.....................................................................................................28
3.5.2 DNS................................................................................................................................31
3.6 Software Dial...........................................................................................................34
Chapter 4. Advantage management setup .......................................................35
Appendix A: FAQ....................................................................................................36
Appendix B: Default Config...................................................................................38

TD-8810 External ADSL2+ Router User Guide
1
Chapter 1.Introduction
Thank you for choosing the TD-8810 External ADSL2+ Router.
1.1 Product Overview
With the excellent circuit design and high quality production, we guarantee the ADSL Router’s
high performance, great stability and easy to use.
The TD-8810 uses integrated ADSL transceiver. The AFE supports full-rate ADSL connectivity
conforming to the ITU and ANSI specifications.
In addition to the basic DMT physical layer functions, the ADSL PHY supports dual latency ADSL
framing (fast and interleaved) and the I.432 ATM Physical Layer.
The TD-8810 is a complete plug-and-play solution. With standard Ethernet interface, it can be
directly connected to any 10M/100M Ethernet devices, support Auto-MDIX.
The TD-8810 not only uses html (web mode through Ethernet port) to configure the Router but
also uses external utility software. You can download it from our website (http://www.tp-link.com).
1.2 Main Features
¾High speed and asymmetry data transmit mode, provides safe and exclusive bandwidth
¾Support All ADSL industrial standards
¾Compatible with all mainstream DSLAM (CO)
¾Firmware upgradeable
¾Provide integrated access of internet and route function which face to SOHO user
¾Advanced DMT modulation and demodulation
¾Real-time Configuration and device monitoring
¾Quick response semi-conductive surge protect circuit, provides reliable ESD and
surge-protect function
1.3 Supporting protocol
- G.992.1 (G.dmt) - Annex A/B/C
- G.992.2 (G.lite) - Annex A/B/C
- ANSI T1.413
- G.992.3 (ADSL2) - Annex A/B/C/M and Annex L (RE-DSL) compliant
- G.992.5 (ADSL) Annex A/B/C and Annex L (RE-DSL) compliant
- ADSL dual latency (fast path and interleaved path)

TD-8810 External ADSL2+ Router User Guide
2
- I.432 ATM physical layer compliant
- Supports RFC2364 (PPPoA)
- Supports RFC2516 (PPPoE)
- Supports RFC1483 (EoA) (Bridged *and Router)
- Supports RFC1577 (IPoA)
)Note:
“*” needs the third-party software.
1.4 Transmit data-rate
¾Max download data-rate: 24Mbps
¾Max upload data-rate: 3.5Mbps
¾Max line length: 6Km
1.5 ATM property
¾AAL0, AAL5, OAM, RM, and raw cell types supported
¾Direct hardware support for 4 Receive VCs, with additional RX VCs and TX VCs supported in
software
¾Full 24-bit Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI)
1.6 System support
¾Support PVC
¾Support NAT、DHCP and so on
¾Support IEEE 802.3、IEEE 802.3u
¾Support 10Base-T/100BASE-TX full-duplex or half duplex Ethernet
¾Support Auto-MDIX
1.7 Working environment
¾Operating temperature: 0 ~40℃℃
¾Storage temperature: -40 ~70℃℃
¾Humidity: 10%~90% (non-condensing)
1.8 Conventions
The Router or TD-8810, or device mentioned in this User guide stands for TD-8810 External

TD-8810 External ADSL2+ Router User Guide
3
ADSL2+ Router without any explanations.
Parameters provided in the pictures are just references for setting up the product, which may
differ from the actual situation.
You can set the parameters according to your demand.

TD-8810 External ADSL2+ Router User Guide
4
Chapter 2.Hardware Installation
The TD-8810 maintains three separate interfaces, one Ethernet, one ADSL and one power
adapter interface.
The Router should not be located where it will be exposed to moisture or excessive heat.
Place the Router in a location where it can be safely connected to the various devices as well as
to a power source.
2.1 System requirement
Confirm your computer has been installed with networking interface card (NIC) before connecting
ADSL Router to your computer, with operating system supporting the TCP/IP protocol.
2.1.1 LED explanation
The front panel of ADSL Router includes one power indicator (RED) and seven function indicators
(GREEN), as explained in chart below:
Name Status Indication
On Power OK
PWR Off Power fail
Quick flash The LINE port is connecting to the ISP’s network
On The LINE port has connected to ISP’s network
ADSL
Off The LINE port has no connection
On There is mistake when ADSL transmitting or receiving data
ALARM Off ADSL normal
On There is data transmitting or receiving on LINE port
ACT Off No data transmitting or receiving on LINE port
On LAN port normal
Off Connection on LAN port abnormal
LAN
Flash Data transmitting or receiving on LAN port
2.2 Rear-panel
¾ON/OFF: Turn on/off the ADSL Router’s power.
¾Power (9V~0.8A input): Please use the provided power adaptor, otherwise may cause
damage to the ADSL Router.
¾RESET (reset default): First press the reset button of Router, then turn on the Router’s
power for at least three seconds. It will resume the default manufacturer’s setup.

TD-8810 External ADSL2+ Router User Guide
5
¾LAN: Connect with your computer’s NIC.
¾LINE (WAN): Connect to the MODEM Port of Splitter or Connect with the telephone line.
2.3 Hardware installation procedures
The procedure to install the Router can be described in general terms in the following steps:
Step 1: Connecting the MODEM port of Splitter with the TD-8810 ADSL Router LINE port by
telephone line. While you need to use a telephone, please attach telephone line into the phone of
Splitter.
Step 2: Connect category 5 cable with RJ45 jacks to the ADSL Router’s LAN port and your
computer’s NIC.
Step 3: Plug one end of the AC Power Adapter into the Power jack on the Ethernet ADSL2+
Router and the other end to a standard electrical outlet.
Step 4: Check the line connection to see if everything is ready. Power up finally.
Figure 2-1

TD-8810 External ADSL2+ Router User Guide
6
Chapter 3.System Configuration
3.1 Computer Configuration
1. Connect the cable according to Chapter 2, turn on the power.
2. Change the IP address of your PC（Figure 3-1）: Open TCP/IP Properties of the LAN card in
your PC, enter the IP address as 192.168.1.*.
)Note:
(* is any value between 2 to 254, Net mask is 255.255.255.0, Gateway is 192.168.1.1, DNS
address is the value provided by ISP).
Figure 3-1
)Note:
Users of Windows 98 can open TCP/IP Properties according to the following: Right-click (Mouse)
Network Neighbor -> Choose Properties -> Double-click TCP/IP.
Users of Windows 2000/NT/XP can do the following: Right-click Network Neighbor -> Choose
Properties -> Right-click Local Connection -> Choose Properties -> Double-click Internet
Protocol (TCP/IP).

TD-8810 External ADSL2+ Router User Guide
7
)Note:
The words in fact may be different with this guide.
Remarks: you can check whether your configuration is successful through PING command. Enter
Ping 192.168.1.1
If the screen looks like the following, you have been successful.
Figure 3-2
If the screen looks like the following, the connection has failed. Please try again.
Figure 3-3
3.2 Login
Startup Internet Explorer, and enter 192.168.1.1;then enter default user name(admin) 、
password(admin), When ADSL connection is OK, you will see the Figure 3-2.

TD-8810 External ADSL2+ Router User Guide
8
Figure 3-4
3.3 Quick Setup
1) Figure 4 is the main page of the Router.
Figure 3-5
2) Please select Quick Setup. Enter the VPI and VCI values provided by your Internet Service
Provider and click Next.

TD-8810 External ADSL2+ Router User Guide
9
Figure 3-6
3) Select the relevant Connection Type and Encapsulation mode as the settings provided by
your Internet Service Provider and click Next.
3.3.1 PPPoA
a) Select PPP over ATM (PPPoA) Connection Type, and click Next.
Figure 3-7
b) Enter the Username and Password provided by your Internet Service Provider and click
Next.

TD-8810 External ADSL2+ Router User Guide
10
Figure 3-8
c) Turn on the selected functions according to your demands. Clicking the next button to
enter the next step.
Figure 3-9
d) Click Save/Reboot.

TD-8810 External ADSL2+ Router User Guide
11
Figure 3-10
3.3.2 PPPoE
a) Select PPP over Ethernet (PPPoE) Connection Type, and click Next.
Figure 3-11
b) Enter the Username and Password provided by your Internet Service Provider and click
Next.

TD-8810 External ADSL2+ Router User Guide
12
Figure 3-12
c) Click Save/Reboot.
Figure 3-13

TD-8810 External ADSL2+ Router User Guide
13
Note：
The Router will restart when you complete the configuration, so you have to wait for a while until it
restarts successfully.
3.3.3 MER
a) Select MAC Encapsulation Routing (MER) Connection Type, and click Next.
b) Enter the parameter and the way which is provided by your ISP, then click Next.

TD-8810 External ADSL2+ Router User Guide
14
Figure 3-14
c) Turn on the selected functions according to your needs. Click Next.
Figure 3-15
d) Click Save/Reboot.

TD-8810 External ADSL2+ Router User Guide
15
Figure 3-16
3.3.4 IPoA
a) Select IP over ATM (IPoA) Connection Type, and click Next.
Figure 3-17