TP-Link NC230 User manual

NC230
HD Day/Night Wi-Fi Cloud Camera
NC250
HD Day/Night Cloud Camera, 300Mbps Wi-Fi
1910011378
REV1.0.0

COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a registered trademark of
TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or
registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used to make any
derivative such as translation, transformation, or adaptation without permission from TP-LINK
TECHNOLOGIES CO., LTD. Copyright © 2015 TP-LINK TECHNOLOGIES CO., LTD. All rights
reserved.
http://www.tp-link.com

FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to pro-vide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment. Such modifications could void the user’s authority to operate the
equipment.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This device and its antenna must not be co-located or operating in conjunction with
any other antenna or transmitter.
“To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile
Configurations. The antennas used for this transmitter must be installed to provide a separation
distance of at least 20 cm from all persons and must not be co-located or operating in conjunction
with any other antenna or transmitter.”
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.

RF Exposure Information
This device meets the EU requirements (1999/519/EC) on the limitation of exposure of the general
public to electromagnetic fields by way of health protection.
The device complies with RF specifications when the device used at 20 cm from your body.
National Restrictions
This device is intended for home and office use in all EU countries (and other countries following
the EU directive 1999/5/EC) without any limitation except for the countries mentioned below:
Country Restriction Reason/remark
Belarus Not implemented
Norway Implemented This subsection does not apply for the geographical area
within a radius of 20 km from the centre of Ny-Ålesund on
Svalbard.
Italy Implemented The public use is subject to general authorisation by the
respective service provider.
Russian
Federation
Limited
implementation
1. SRD with FHSS modulation
1.1. Maximum 2.5 mW e.i.r.p.
1.2. Maximum 100 mW e.i.r.p. Permitted for use SRD for
outdoor applications without restriction on installation height
only for purposes of gathering telemetry information for
automated monitoring and resources accounting systems.
Permitted to use SRD for other purposes for outdoor
applications only when the installation height is not exceeding
10 m above the ground surface.
1.3.Maximum 100 mW e.i.r.p. Indoor applications.
2. SRD with DSSS and other than FHSS wideband
modulation
2.1. Maximum mean e.i.r.p. density is 2 mW/MHz. Maximum
100 mW e.i.r.p.
2.2. Maximum mean e.i.r.p. density is 20 mW/MHz. Maximum
100 mW e.i.r.p. It is permitted to use SRD for outdoor
applications only for purposes of gathering telemetry
information for automated monitoring and resources
accounting systems or security systems.
2.3. Maximum mean e.i.r.p. density is 10 mW/MHz. Maximum
100 mW e.i.r.p. Indoor applications.
Ukraine Limited
implementation
e.i.r.p. ≤100 mW with built-in antenna with amplification factor
up to 6 dBi.
ATTENTION: Due to EU law, the country settings must be identical to the country where the
device is operating (important due to non-harmonised frequencies in the EU).
Canadian Compliance Statement
This device complies with Industry Canada license-exempt RSSs. Operation is subject to the
following two conditions:
1）This device may not cause interference, and
2）This device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :

1）l’appareil ne doit pas produire de brouillage;
2）l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, meme si le
brouillage est susceptible d’en compromettre le fonctionnement.
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20
cm de distance entre la source de rayonnement et votre corps.
Industry Canada Statement
CAN ICES-3 (B)/NMB-3(B)
Korea Warning Statements:
당해 무선설비는 운용중 전파혼신 가능성이 있음.
NCC Notice
注意！
依據 低功率電波輻射性電機管理辦法
第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、
加大功率或變更原設計之特性或功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通行；經發現有干擾現象時，應立即
停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業之無線電信。低功率射
頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。
減少電磁波影響，請妥適使用。
BSMI Notice
安全諮詢及注意事項
請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。
清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。
注意防潮，請勿將水或其他液體潑灑到本產品上。
插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。
請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。
請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。

Продукт сертифіковано згідно справилами системи УкрСЕПРО на відповідність вимогам
нормативних документів та вимогам, що передбачені чинними законодавчими актами
України.
Safety Information
When product has power button, the power button is one of the way to shut off the product;
when there is no power button, the only way to completely shut off power is to disconnect the
product or the power adapter from the power source.
Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock and
voiding the limited warranty. If you need service, please contact us.
Avoid water and wet locations.
Adapter shall be installed near the equipment and shall be easily accessible.
The plug considered as disconnect device of adapter.
Use only power supplies which are provided by manufacturer and in the original
packing of this product. If you have any questions, please don't hesitate to contact us.
This product can be used in the following countries:
AT BG BY CA CZ DE DK EE
ES FI FR GB GR HU IE IT
LT LV MT NL NO PL PT RO
RU SE SG SK TR UA US
Explanation of the symbols on the product label
Symbol Explanation
DC voltage
RECYCLING
This product bears the selective sorting symbol for Waste electrical and electronic
equipment (WEEE). This means that this product must be handled pursuant to
European directive 2012/19/EU in order to be recycled or dismantled to minimize
its impact on the environment.
User has the choice to give his product to a competent recycling organization or to
the retailer when he buys a new electrical or electronic equipment.

TP-LINK TECHNOLOGIES CO., LTD
DECLARATION OF CONFORMITY
For the following equipment:
Product Description: HD Day/Night Wi-Fi Cloud Camera
Model No.: NC230
Product Description: HD Day/Night Cloud Camera, 300Mbps Wi-Fi
Model No.: NC250
Trademark: TP-LINK
We declare under our own responsibility that the above products satisfy all the technical regulations
applicable to the product within the scope of Council Directives:
Directives 1999/5/EC, Directives 2004/108/EC, Directives 2006/95/EC, Directives 1999/519/EC,
Directives 2011/65/EU
The above product is in conformity with the following standards or other normative documents
EN 300 328 V1.8.1
EN 301 489-1 V1.9.2 & EN 301 489-17 V2.2.1
EN 55022: 2010 + AC: 2011
EN 55024: 2010
EN 60950-1: 2006 + A11: 2009 + A1: 2010 + A12: 2011 +A2: 2013
EN 62311: 2008
The product carries the CE Mark:
Person responsible for making this declaration:
Yang Hongliang
Product Manager of International Business
Date of issue: 2015-12-09
TP-LINK TECHNOLOGIES CO., LTD.
Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park,
Shennan Rd, Nanshan, Shenzhen, China

CONTENTS
Chapter 1About this Guide.................................................................................... 1
1.1Conventions..................................................................................................................1
1.2Overview of This Guide ................................................................................................1
Chapter 2Get to know about your camera ........................................................... 2
2.1Product Overview .........................................................................................................2
2.2Main Features...............................................................................................................2
2.3Panel Appearance ........................................................................................................3
2.3.1Front Panel ........................................................................................................3
2.3.2Rear Panel.........................................................................................................4
Chapter 3Set Up Your Camera .............................................................................. 6
3.1Set up the Camera With the tpCamera APP.................................................................6
3.2Position Your Camera ...................................................................................................7
Chapter 4Configure Your Camera......................................................................... 9
4.1Log in to Your Camera ..................................................................................................9
4.2Live View .................................................................................................................... 11
4.3Basic...........................................................................................................................13
4.3.1Basic > Status ..................................................................................................13
4.3.2Basic > Network...............................................................................................15
4.3.3Basic > Wireless Connection ...........................................................................16
4.3.4Basic > Cloud Setting.......................................................................................18
4.3.5Basic > LED .....................................................................................................19
4.4Advanced....................................................................................................................19
4.4.1Advanced > Status...........................................................................................20
4.4.2Advanced > Network........................................................................................20
4.4.3Advanced > Wireless Connection ....................................................................23
4.4.4Advanced > Wireless Extender........................................................................25
4.4.5Advanced > Cloud Setting ...............................................................................26
4.4.6Advanced > DDNS...........................................................................................26
4.4.7Advanced > Video............................................................................................27
4.4.8Advanced > Motion Detection ..........................................................................28
4.4.9Advanced > Sound Detection ..........................................................................29
4.4.10Advanced > Notification Delivery .....................................................................30
4.4.11Advanced > LED..............................................................................................34
4.5System........................................................................................................................34
4.5.1Account............................................................................................................35
4.5.2Date/Time ........................................................................................................37
4.5.3Management ....................................................................................................39
4.5.4System Log......................................................................................................41
Appendix: Specifications....................................................................................... 42

NC230 HD Day/Night Wi-Fi Cloud Camera
NC250HD Day/Night Cloud Camera, 300Mbps Wi-Fi
1
Chapter 1 About this Guide
This User Guide contains information for setup and management of the Cloud Camera. Please
read this guide carefully before operation.
1.1 Conventions
In this Guide the following conventions are used:
The camera mentioned in this Guide stands for NC230 and NC250 without any explanation.
This User Guide is shared by NC230 and NC250. NC250 is used for demonstration in this
guide. The difference between them are:
1. Max Frame Rate: 20 fps for NC230; 30 fps for NC250.
2. Wi-Fi Data Rate: 150Mbps for NC230; 300Mbps for NC250.
Bold font indicates a button, a toolbar icon, menu or menu item.
Symbol in this Guide：
Symbol Description
Note: Ignoring this type of note might result in a malfunction or damage to the
device.
1.2 Overview of This Guide
Chapter Introduction
Chapter 1 About This Guide Introduces the guide structure and conventions.
Chapter 2 Get to know about
your camera
Introduces the features, application and appearance of the
camera.
Chapter 3 Set up your camera Introduces how to quickly set up the camera using the
tpCamera app and how to position your camera.
Chapter 4 Managing the
Camera
Introduces how to configure the camera using the built-in web
management page.

NC230 HD Day/Night Wi-Fi Cloud Camera
NC250HD Day/Night Cloud Camera, 300Mbps Wi-Fi
2
Chapter 2 Get to know about your camera
2.1 Product Overview
TP-LINK Cloud Camera is a versatile solution for home and office monitoring to keep an eye on
your home, kids or workplace, whatever you care for most.
TP-LINK Cloud Camera is a cloud-based Wi-Fi video monitoring device with free live streaming
and remote viewing, which makes it easy to stay connected with what you care most wherever you
are. You can view and manage your camera from anywhere over the Internet through the TP-LINK
Cloud website or through the tpCamera app for iOS and Android devices.
Through the camera’s web management page, you can view the status of the camera, and
configure lots of settings of the camera, such as network setting, the cloud setting, the motion
detection, and the notification delivery.
With Night Vision function, TP-LINK Cloud Camera lets you view even in darkness.
With Motion Detection function, TP-LINK Cloud Camera can send you immediate notification by
email or FTP whenever motion or sound is detected automatically, allowing you to remain aware of
whatever is happening on the ground.
With a stable high speed Wi-Fi connection of up to 300Mbps for NC250, and 150Mbps for NC230,
you can enjoy fluid video streaming with ease. In addition, the TP-LINK Cloud Camera can also
expand your Wi-Fi network with its Wi-Fi Extender functionality.
With the sticky pad or screws, you can place your camera anywhere you want, on the table, the
wall, or even on the ceiling.
2.2 Main Features
Night Vision - Automatic night vision functionality supports 24-hour surveillance
Advanced H.264 Video - For amazingly smooth HD video streaming
tpCamera App - Use the free tpCamera app to set up, view and manage the camera remotely
with your iOS and Android devices
TP-LINK Cloud (www.tplinkcloud.com) access for easy viewing and management
Web-based management page for basic and advanced configurations
Easy Setup – Connect and follow the tpCamera app’s instruction to install and operate the
camera within minutes
Motion & Sound Detection - Immediate notification by email or FTP whenever motion or sound
is detected

NC230 HD Day/Night Wi-Fi Cloud Camera
HD Day/Night Cloud Camera, 300Mbps Wi-FiNC250
3
Email or FTP notification triggered by motion detection
Wireless connectivity compliant with WPS button
Instantly eliminates the dead zones and expand your home’s wireless network
Support wireless 802.11b/g/n with speed up to 300Mbps for NC250, and 150Mbps for NC230.
Ethernet port for wired connectivity
UPnP support for network setup & configuration
10x digital zoom for close-up viewing
2.3 Panel Appearance
2.3.1 Front Panel
Light Sensor
Microphone
System LED
Figure 2-1 Front Panel
Light Sensor: The camera has a built-in internal photodetector. It is used to identify day or
Microphone: The camera has a built-in internal microphone. This microphone is hidden in
night.

the pinhole located on the front panel.

NC230 HD Day/Night Wi-Fi Cloud Camera
HD Day/Night Cloud Camera, 300Mbps Wi-FiNC250
4
System LED:
Status Indication
Flashing Red The camera starts booting up.
Solid Red The camera has boot up, but is not connected to any network.
Flashing Green The camera is in firmware upgrade procedure.
Solid Green The camera is connected to a network or is transferring data.
2.3.2 Rear Panel
Figure 2-2 Rear Panel
WPS LED:
Status Indication
The camera starts booting up.
Flashing Green The camera is connecting to a network by WPS function. This
process will last in the first 2 minutes.
The camera has boot up.
Off The camera failed to be added to a network by WPS function.
Solid Green The camera has been successfully added to a network by WPS
function. This process will last in the first 2 minutes.
ETHERNET Port
WPS LED
Power Jack
Heat Emission Holes
WPS/RESET
Button

NC230 HD Day/Night Wi-Fi Cloud Camera
NC250HD Day/Night Cloud Camera, 300Mbps Wi-Fi
5
ETHERNET Port: The ETHERNET port is used to connect the camera to a network via RJ45
cable.
Power Jack: The power jack is where you connect the AC adapter to the camera.
WPS/RESET Button: This button is used for both WPS and RESET function. To use the WPS
function, press it for 1 second. To use the RESET function, press and hold for more than 5
seconds.
Used as WPS button:
If your wireless router supports WPS (Wi-Fi Protected Setup), you can connect the
camera to your Wi-Fi network using WPS. Press the WPS or QSS button on your router.
Within 2 minutes, press the WPS/RESET button on the camera for about 2 seconds,
then the LED above this button will start flashing quickly. When this LED becomes solid
on, the WPS is successful.
Used as RESET button:
With the camera powered on, press and hold the WPS/RESET button (more than 5
seconds) until the System LED turns off. Then release the button and wait the camera to
reset to its factory default settings.
Heat Emission Holes: These holes are used for heat dissipation.

NC230 HD Day/Night Wi-Fi Cloud Camera
HD Day/Night Cloud Camera, 300Mbps Wi-FiNC250
6
Chapter 3 Set Up Your Camera
3.1 Set up the Camera with the tpCamera APP
You can install your camera in minutes with the free tpCamera app. If your router has a WPS
button, you can complete the setup wirelessly using WPS function. Please follow the steps below
to set up your camera.
Step 1. Connect the camera to the network your smartphone is on.
Before you start the setup process, get your smartphone and make sure that it is connected to
your home network. To use the tpCamera app, your smartphone’s operating system should meet
these requirements: Android 3.0 or higher; iOS 7.0 or higher.
Steps for connecting your camera to the router are:
1) Power on the camera using the provided power supply unit as shown.
2) Connect a smartphone to the router as shown.
3) Connect the camera to the router via wired or wireless connection, and then wait till the
camera’s system LED become solid green.
Wired: Connect the camera to the router’s LAN port via an Ethernet cable.
Wireless: If your wireless router supports WPS, you can connect the camera to your Wi-Fi
network using WPS. Press the WPS or QSS button on your router. Within 2 minutes, press
the WPS/RESET button on the back of the camera for about 2 seconds, then the LED above
this button will start flashing quickly. When this LED becomes solid on, the WPS is successful
and the camera is connected to the router wirelessly.
SmartphoneCameraOutlet
W
ireless Router
LAN WAN
Internet
ETHERNET9V 0.6A

NC230 HD Day/Night Wi-Fi Cloud Camera
HD Day/Night Cloud Camera, 300Mbps Wi-FiNC250
7
Step 2. Download and install the tpCamera app.
You can download the free tpCamera app from the App Store or Google play. You can also scan
the QR code below to download the tpCamera app.
OR
Step 3. Add the camera to your TP-LINK Cloud account.
Launch the tpCamera app, log into your TP-LINK Cloud account or create one if you do not have
an account. Then follow the app instructions to add your new camera to your account.
When you reach the My Cam page, you have successfully added your camera and can start to
use your camera.
3.2 Position Your Camera
Before positioning your camera, please keep these safety guidelines in mind:
Keep your camera out of reach of children and pets.
Use your camera only indoors, and keep it out of direct sunlight. Make sure its operating
temperature is in the range of 0-40°C (32-104°F).
Pick a location which is close enough to a wall outlet.
Use only the power adapter that comes with this camera in the package.
You can place your camera to your desired location. Just unplug and replug it without having to go
through the app’s setup again, and then you can use it in a wired or wireless way as you’ve set in
the app’s setup process. If you use the camera wirelessly, please place the camera within the
coverage of your wireless network. You can place the camera in various ways:
Place it on a flat surface.
Stick it with the included adhesive.
Mount it as shown below.
Detailed instructions on mounting your camera to a wall or ceiling are shown as follows. Before
you start to mount the camera, prepare two screws which meet the following requirements.

NC230
NC250
HD Day/Night Wi-Fi Cloud Camera
HD Day/Night Cloud Camera, 300Mbps Wi-Fi
8
1. Unscrew the camera head.
2. Remove the base cover.
3. Use two screws (not included) to secure
the base.
4. Put the base cover and camera head back
on.
After relocating your camera, face it towards the area you’d like to view, and then plug the power
adapter into a power outlet.
Now that you’ve finished positioning your camera, use the tpCamera app to check that your
camera can see what you want to keep an eye on. Adjust its position if you need to.

NC230 HD Day/Night Wi-Fi Cloud Camera
HD Day/Night Cloud Camera, 300Mbps Wi-FiNC250
9
Chapter 4 Configure Your Camera
You can use the tpCamera app and TP-LINK Cloud (www.tp-linkcloud.com) to view and manage
your camera remotely. To configure the camera’s settings, such as the network settings, cloud
settings, notification delivery, you should use the camera’s built-in web management page in your
local network.
4.1 Log in to Your Camera
1. Connect a computer to the router that your camera is connected to. You can use an Ethernet
cable or connect it to the router’s Wi-Fi network.
2. Find the management IP address of the camera from the web management page of the
router. Here we use the web management page of TP-LINK Archer D20 for demonstration.
3. On a computer that connects to the same router as the camera does, open a web browser,
type in the camera’s IP address in the address field, and press Enter. Here we use
http://192.168.0.106 for demonstration.
4. Enter the default username and password (admin/admin). Click Login.

NC230 HD Day/Night Wi-Fi Cloud Camera
HD Day/Night Cloud Camera, 300Mbps Wi-FiNC250
10
Note:
For the administrator, the default password is “admin”. We recommend that you change it in the
Account menu. (Go to “System > Account”)
If you log in to the camera as an administrator, you can perform all the settings provided by the
camera.
If you log in to the camera as a common user, you can only view the Live View. After logging as
administrator, you can add up to five user accounts in the Account menu. (Go to “System >
Account”)
5. Click Download to download and install the required plugin.
Note:
If the installed plugin doesn't work, set your browser security settings to allow plugins. Here we
take the settings for IE browser as an example. Go to "Tools > Internet Options > Security".
Click "Internet > Custom Level", find the item "Download signed ActiveX controls" and check
Prompt. Click "Local Intranet > Custom Level", find the item "Download signed ActiveX
controls" and check Prompt.
6. After the plugin is successfully installed, refresh the webpage to display the monitor video.

NC230 HD Day/Night Wi-Fi Cloud Camera
HD Day/Night Cloud Camera, 300Mbps Wi-FiNC250
11
4.2 Live View
The Live View screen shows you the live video feed from your camera. On this screen, you can
capture a picture, record a video and so on.

NC230 HD Day/Night Wi-Fi Cloud Camera
HD Day/Night Cloud Camera, 300Mbps Wi-FiNC250
12
Symbols Meaning Note
Click to capture a still
image shot by the
camera.
The image file will be saved to your local
computer. You can select a save path and rename
the image file.
Click to record the
current video.
The video file will be saved to your local computer.
You can select a save path and rename the video
file.
The icon will turn yellow once the save
path is selected. If you want to stop recording, just
click .
Click to vertically flip the
current image.
Click to horizontally flip
the current image.
If the camera is installed upside down, Flip Image
and Mirror should both be checked.
Click to choose a camera
working mode.
You can set the camera working mode to Auto
(), Day ( ), or Night ( ).
Drag the slider to adjust
the size of the current
image.
The maximum zoom ratio is 10 times.
Mute off. You can hear
the current sound by the
camera.
Click and it will become .
Mute on. The current
sound by the camera is
turned off.
Click and it will become .
Drag the slider to adjust
the sound volume.
You can adjust the sound volume only with mute
off .
Click to enlarge the
current image to full
screen display.
Press ESC key to return to the original screen
display.
Brightness: Drag the slider to adjust the brightness level of
camera. Large value will brighten the current displayed screen.