TradeQuip 2057T User manual

June-22
Product Code: 2057T
Made in China to TQB Brands Pty Ltd specifications.
Visit us at www.tqbbrands.com.au
Product Code: 2057T
TRANSMISSION
LIFTER
Specifications
•Safe Working Capacity: 1,000kg
•Maximum Height: 725mm
•Minimum Height: 205mm
•Cradle Size: 340x200mm
•Cradle Tilt Forward: 70°
•Cradle Tilt Back: 15°
•Cradle Lateral Adjustment: 90mm
•Chassis: 850(L)x490(W)x305(H)mm
•Nett Weight: 54kg
•Carton 910 x 520 x 260mm
•Gross Weight: 59.5kg
About the TradeQuip brand
The 'TradeQuip' brand of workshop equipment, is designed for use in a demanding workshop
environment by professional users. With proven and trusted “Made for the
Trade” reliability, 'TradeQuip' branded products offer the very best in performance for an
affordable price. All backed by a 1year trade guarantee across 1,000+ distributors Australia

June-22
Product Code: 2057T
Made in China to TQB Brands Pty Ltd specifications
Visit us at www.tqbbrands.com.au
Page 2
IMPORTANT: READ ALL INSTRUCTIONS BEFORE USE
WARNING
The instructions and warnings contained in this manual should be read and understood before using or operating this equipment.
Do not allow anyone to use or operate this equipment until they have read this manual and have developed a thorough
understanding of how this equipment works. Failure to observe any of the instructions contained in the manual could result in
severe personal injury to the user or bystanders, or cause damage to the equipment and property. Keep this manual in a
convenient and safe place for future reference.
Whilst every effort has been made to ensure accuracy of information contained in this manual, the TQB Brands Pty Ltd policy of
continuous improvement determines the right to make modifications without prior warning.
WARNING .................................................................................................................................................................................................................. 2
CONTENT................................................................................................................................................................................................................... 2
STANDARD OPERATING PROCEDURE ........................................................................................................................................................................ 3
ASSEMBLY, OPERATION, PREVENTITIVE MAINTENANCE........................................................................................................................................... 4
PARTS DIAGRAM........................................................................................................................................................................................................ 6
PARTS LIST ................................................................................................................................................................................................................. 7
TROUBLESHOOTING .................................................................................................................................................................................................. 8
WARRANTY................................................................................................................................................................................................................ 9
USE THIS PRODUCT FOR ITS INTENDED PURPOSE ONLY
INTENDED USE
Designed for the removal, installation, and transportation (in the lowered position) of passenger vehicle transmissions that are raised
by an in-ground or above-ground lift
WARNING
CONTENT

June-22
Product Code: 2057T
Made in China to TQB Brands Pty Ltd specifications
Visit us at www.tqbbrands.com.au
Page 3
Safety glasses must be worn when operating this
equipment
Safety footwear must be worn when operating
this equipment
Long loose hair must be contained when operating
this equipment
Close fitting/protective clothing must be worn
when operating this equipment
Rings and jewellery must not be worn when
operating this equipment
PRE-OPERATIONAL SAFETY CHECKS
Save these instructions. For your safety, read, understand, and follow the information provided with and on this 1,000kg
Transmission Lifter before using.
•DO NOT exceed the maximum lifting load capacity of 1000kg.
•Only use this Transmission Lifter on a surface that is stable, level, smooth, dry and capable of sustaining the load. Keep the
surface free from unrelated materials and ensure that there is adequate lighting.
•DO NOT use on tarmac, or any other soft surface as the transmission may sink or topple.
•Vehicle must be properly and adequately supported before commencing work with this Transmission Lifter.
•This Transmission Lifter is used as an aid in the removal and installation of a transmission or a differential, as individual
components. DO NOT use it for any other purpose than it is designed for.
•Always centre the load on the cradle of this Transmission Lifter and be sure the transmission is stable and secure before raising
or lowering.
•DO NOT use the Transmission Lifter to lift or support a heavy load such as a differential with axle or a transmission with bell
housing which is bulky and difficult to balance, and may cause the transmission lifter to tip over and lead to equipment damage
and/or serious personal injury.
•Never move this Transmission Lifter with a load any higher off the ground than necessary and always move it slowly and
carefully.
•Transfer the load immediately to appropriate support device for service or repair.
•DO NOT operate this Transmission Lifter when you are tired or under the influence of alcohol, drugs or any intoxicating
medication.
•DO NOT allow untrained persons to operate this product and DO NOT make any modifications to this product.
•DO NOT tamper with the safety valve.
•DO NOT expose the Transmission Lifter to rain or any other kind of inclement weather.
•When servicing, use only TradeQuip identical replacement parts. Use of any other parts will void the warranty.
•Use the right product for the job. There are certain applications for which this Transmission Lifter was designed. Do not modify
the Transmission Lifter and do not use the Transmission Lifter for a purpose for which it was not intended.
Warning: Vehicle must be properly and adequately supported before commencing work with this Transmission Jack.
INTENDED USE
Designed for the removal, installation and transportation (in the lowered position) of passenger vehicle transmissions that are
raised by an in-ground or above-ground lift.
DO NOT use this machine unless you have been trained and assessed to a competent level in its sate use and operation, and
have been given permission to use this
STANDARD OPERATING PROCEDURE

June-22
Product Code: 2057T
Made in China to TQB Brands Pty Ltd specifications
Visit us at www.tqbbrands.com.au
Page 4
1. FEATURES
This TradeQuip "Made for the Trade” 1,000kg Hydraulic Low Profile Transmission Lifter is perfect for transmission installation
and removal. Features smooth, manually operated hydraulic lifting and lowering and a 360° rotating handle for better load
positioning. The universal mounting cradle provides a wide forward, backward and side to side tilt range. This Transmission
Lifter makes transmission removal and replacement easy and safe. Featuring four quality swivel castors for mobility, this
tough Transmission Lifter is also formed and welded with extra strong steel plates for ultimate durability.
2. BEFORE USE
Prior to each use conduct a visual inspection by checking for abnormal conditions, such as cracked joints and damaged,
loose, or missing parts.
Purge the hydraulic system to eliminate any air in the system.
Bleeding Instructions:
1. Remove the Filler Bung and if required, refill with *32 Grade Hydraulic until the oil is
approximately 6mm below the filler hole then replace the Filler Bung.
Oil
2. Leaving the Pump Handle in the lowered position, open the release knob one eighth
turn anticlockwise.
3. With one foot on the front axle assembly, slowly raise the lift arm by hand to three
quarter height and release, the lift arm will slowly fall back to lowered position.
4. Remove the oil filler bung from the top of the hydraulic ram and turn the release
valve anticlockwise to open.
5. Replace the filler bung and pump the handle up and down quickly several times to
bleed air from the pump system.
6. Recheck the hydraulic oil level and refill to 6mm below the fill port if required before
replacing the filler bung.
7. If necessary, repeat the process steps 2 to 6
At this point both the Pump and Lift Ram should be free of air and the Jack ready for operation
If the pump still feels spongy or load is slow to raise, seek the services of a qualified Hydraulic repairer.
Filler
Bung/
Breather
ASSEMBLY, OPERATION, PREVENTITIVE MAINTENANCE

June-22
Product Code: 2057T
Made in China to TQB Brands Pty Ltd specifications
Visit us at www.tqbbrands.com.au
Page 5
3. OPERATION
Warning:
Vehicle must be properly and adequately supported before commencing work with this transmission lifter.
Removing a Transmission
1. Before each use check the hydraulic oil level and fill to 6mm below the fill port.
2. Once the vehicle is raised and secured on Jack Stands, clear the area underneath the vehicle.
3. Disconnect one end of the chain and allow it to hang free.
4. Move the Transmission Lifter underneath the transmission.
5. Close the release valve.
6. Pump the handle to raise the transmission lifter.
7. Stop just below the transmission and align the saddle to the transmission with the tilt knobs.
8. Continue raising the saddle up to the transmission to determine where you will need to adjust the supports. All four
supports need to grip and make contact with the transmission.
9. After determining where they need to be set, loosen the threaded bolts on each support, and adjust it to the proper
setting for the transmission. Tighten the bolts.
10. Raise the unit again to make contact with the transmission, making sure all of the supports are in firm contact.
11. Wrap the chain securely around the transmission, and hook the chain to the bracket on the other side of the saddle.
12. Once it is securely fastened, release the bolts holding the transmission in place.
13. Make sure the area is clear of people and tools, and check the transmission is securely held in place.
14. Slowly open the release valve to lower the Transmission Lifter.
15. Move the Transmission Lifter from under the vehicle and perform the necessary maintenance.
Re-installing a Transmission
1. Move the Transmission Lifter so that the transmission is lined up properly with its connection points.
2. Close the release valve.
3. Pump the handle to gradually raise the Transmission Lifter, whilst guiding the transmission into place.
4. Secure the transmission into place using its hardware.
5. Ensure the transmission is securely installed.
6. Disconnect one end of the chain and allow it to hang free.
7. Clear the area near the Transmission Lifter, and slowly open the release valve to lower the lifter.
8. Move the Transmission Lifter clear of the vehicle.
4. STORAGE
This Transmission Lifter should always be stored with the lift arm fully lowered in a dry location on a level surface.
5. MAINTENANCE
Replace or repair damaged parts. Use recommended TradeQuip parts only. Non- authorised parts may be dangerous and
will invalidate the warranty. Periodic maintenance is essential for the efficient operation of Manual Transmission lifts. Lack
of lubrication can cause severe wear and or premature failure.
Changing the Hydraulic Oil
1. Change the hydraulic jack oil at least once a year.
2. Fully lower the Transmission Lifter, remove the oil fill plug on the side of the hydraulic ram.
3. Tip the Transmission Lifter to allow the old hydraulic oil to drain out of the housing completely, dispose of the old
hydraulic oil in accordance with local regulations.
4. With the Transmission Lifter upright, completely fill the hydraulic ram with a high quality hydraulic oil (not included)
until the oil just begins to run out of the oil fill hole.
5. Open the release valve and pump the handle to bleed air from the system by following the Bleed Instructions on Page4
6. Reinstall the oil filler plug.
7. Clean with a clean cloth using a mild detergent.
8. Always store the transmission lifter in a safe, dry location.

June-22
Product Code: 2057T
Made in China to TQB Brands Pty Ltd specifications
Visit us at www.tqbbrands.com.au
Page 6
Lubrication Instructions
1. All lower lift arm pivots and pins in all linkages should be lubricated with a Light Bearing Grease or 30/40W Machine Oil
to ensure long life and prevent premature wear.
2. Wheels and Castor axles and bearing races should be lubricated with a Light Bearing Grease or 30/40W Machine Oil to
ensure long life and prevent premature wear.
3. Cradle Pins, Pivots and Threaded Adjustor Rods [marked X] should be lubricated with a Light Bearing Grease or 30/40W
Machine Oil to ensure long life and prevent premature wear.
4. Pivoting Pump Handle Type Mechanisms should be lubricated with a light bearing grease or 30W/40W Machine Oil.
6. SERVICE & REPAIR
Any Transmission Lifter found damaged in any way, or found to be worn or operates abnormally should be removed from
service until repaired by an authorised service agent. Owners and / or operators should be aware that repair of this product
may require specialised equipment and knowledge. Only authorised parts, labels and decals shall be used on this equipment.
Annual inspection of the transmission lifter is recommended and can be made by an authorised repair facility to ensure that
your equipment is in optimum condition and that the equipment has the correct decals and safety labels specified by the
manufacturer.
Part
Description
Qty
1
Working Table
1
2
Adjusting Handle
1
3
Adjusting Handle
1
Part
Description
Qty
4
Connect Rod
1
5
Upper Frame
1
6
Main Frame
Part
Description
Qty
7
Pump
1
8
Castor Wheel
4
9
Towing Hook
1
PARTS DIAGRAM

June-22
Product Code: 2057T
Made in China to TQB Brands Pty Ltd specifications
Visit us at www.tqbbrands.com.au
Page 7
Parts #
Description
Qty
Parts #
Description
Qty
1
Release Valve Lever
1
21
Pump Washer M25x9x1.2
1
2
O Ring
2
22
Oil Seal Screw M10x1x15
2
3
Steel Ball M7
1
23
O Ring M8.5x2.65
2
4
Lock Screw
1
24
Oil Seal Screw M10x1x15
1
5
Steel Ball M12
1
25
Flat Washer M15x8.5x2
1
6
Spring
1
26
Pressure Adjusting Screw M10x1
1
7
Steel Ball M9.5
1
27
Pressure Adjusting Spring M7.5x2x16.5
1
8
Steel Ball M7
1
28
Ball Head
1
9
Oil Seal Screw
1
29
Steel Ball M4
1
10
Rubber Flat Washer
1
30
Screw M16x20
1
11
Pressure Adjusting Screw
1
31
Steel Ball M12
1
12
Spring
1
32
High Pressure Spring M0.6x9.5x22
1
13
Round Pin M8x32
1
33
Steel Ball M9.5
1
14
Rod M 28.5x65
1
34
Steel Ball M6
1
15
Pump Core M14x82
1
35
Oil Return Valve
1
16
O Ring M9.5x2.65
1
36
O ring M7.8x1.9
1
17
Polyurethane M8x14x6
1
37
Base
1
18
Pump Body m27x14x68
1
38
Cotter Pin M4x40
1
19
1
39
1
20
1
PARTS LIST

June-22
Product Code: 2057T
Made in China to TQB Brands Pty Ltd specifications
Visit us at www.tqbbrands.com.au
Page 8
Problem
Symptom
Cause
Conclusion
Solution
Jack will not lift
using manual
pump
Manual pump has no
resistance, lift arm will
not raise
Release handle valve
pin obstructed
Load weight exceeds
lift capacity &
overload actuated
Valve seat/check ball
failure
Higher capacity jack
required
Relief valve needs reset
Re-adjust release handle
position
Select higher capacity Jack
Contact qualified
technician for repairs
Manual pump has
resistance, lift ram
raises and falls with up
and down pump strokes
Main check ball fails to
seal
Obstruction in main
check valve
Bleed pump and ram as
per owners manual
instructions
Jack will not
hold load
Load cannot be
sustained, lift ram drops
under load
Release valve closed
but failure to raise lift
arm
Valve check ball off
centre not contacting
valve seat correctly
Contact qualified
technician for repairs
Damaged main seal
external leak at lift ram
Replace main ram seals Contact qualified
technician for repairs
Pump handle rises Main check valve
obstructed
Replace main check
valve ball and reseat
valve seat
Contact qualified
technician for repairs
Poor lift
performance
Pump has no resistance,
lift ram will not raise to
full stroke
Low oil level
Air trapped in system
due to cavitation
caused by air pressure
build up in reservoir
Fill fluid to correct level
Lift ram raised for
extended period causing
air ingress to hydraulic
system
Fill fluid to correct level
then bleed system
With ram fully retracted,
open the breather to let
pressurised air escape
then bleed system
Contact qualified
technician for repairs
TROUBLESHOOTING

June-22
Product Code: 2057T
Made in China to TQB Brands Pty Ltd specifications
Visit us at www.tqbbrands.com.au
Page 9
TradeQuip products have been carefully tested and inspected before shipment and are guaranteed to be free from defective
materials and workmanship for a period of 12 months from the date of purchase except where tools are hired out when the
guarantee period is ninety days from the date of purchase.
Should the machine develop any fault, please return the complete tool to your nearest authorised warranty repair agent or contact
TQB Brands Pty Ltd Warranty team – [e-mail].
If upon inspection it is found that the fault occurring is due to defective materials or workmanship, repairs will be carried out free
of charge. This guarantee does not apply to normal wear and tear, nor does it cover any damage caused by misuse, careless or
unsafe handling, alterations, accident, or repairs attempted or made by any personnel other than the authorised TQB Brands Pty
Ltd repair agent.
This guarantee applies in lieu of any other guarantee expressed or implied and variations of its terms are not authorised.
Your TQB Brands Pty Ltd guarantee is not effective unless you can produce upon request a dated receipt or invoice to verify your
proof of purchase within the 12 month period.
Consumer Guarantee
Our goods come with a guarantee that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement
or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have
the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
All images and illustrations shown are for reference purposes only. All information, specifications and illustrations in this manual
are based on the latest information available at the time of publication and are subject to change without notice. The
information in this manual is periodically revised to ensure the latest information is included. Download the latest version of this
manual and other related technical documentation from www.tqbbrands.com.au.
WARRANTY