TRADIM 3107X Series User manual

INSTRUCTION MANUAL FLOOR DIMMER 31070-SERIES
This floor dimmer is only suitable for low-voltage halogen lamps
(12V 35-150W). The 230V-12V transformer is integrated into this floor
dimmer (no external transformer required). Use only indoors.
INSTALLATION:
• Always switch off the power before installation!
• Unscrew the housing and remove the top side.
• Strip the power wires and connect them following the drawing.
• Put back the top side and make sure the wires are securely
clamped underneath the tension relief.
• Tighten the screws on the bottom.
31070-SERIES
The manufacturer is not liable for damage caused by the incorrect use or
incorrect installation of the dimmer.
The warranty period is 2 years from the
date of purchase, to be proven to the retailer by means of your purchase receipt.
Keep this manual in a safe place in case it is needed for (re)installation!
TRADIM Aalsbergen 15, 6942 SE Didam, The Netherlands www.tradim.nl
Version 2.0 ENG (25/01/19)
INSTRUCTION MANUAL FLOOR DIMMER 31070-SERIES
This floor dimmer is only suitable for low-voltage halogen lamps
(12V 35-150W). The 230V-12V transformer is integrated into this floor
dimmer (no external transformer required). Use only indoors.
INSTALLATION:
• Always switch off the power before installation!
• Unscrew the housing and remove the top side.
• Strip the power wires and connect them following the drawing.
• Put back the top side and make sure the wires are securely
clamped underneath the tension relief.
• Tighten the screws on the bottom.
31070-SERIES
The manufacturer is not liable for damage caused by the incorrect use or
incorrect installation of the dimmer.
The warranty period is 2 years from the
date of purchase, to be proven to the retailer by means of your purchase receipt.
Keep this manual in a safe place in case it is needed for (re)installation!
TRADIM Aalsbergen 15, 6942 SE Didam, The Netherlands www.tradim.nl
Version 2.0 ENG (25/01/19)
INSTRUCTION MANUAL FLOOR DIMMER 31070-SERIES
This floor dimmer is only suitable for low-voltage halogen lamps
(12V 35-150W). The 230V-12V transformer is integrated into this floor
dimmer (no external transformer required). Use only indoors.
INSTALLATION:
• Always switch off the power before installation!
• Unscrew the housing and remove the top side.
• Strip the power wires and connect them following the drawing.
• Put back the top side and make sure the wires are securely
clamped underneath the tension relief.
• Tighten the screws on the bottom.
31070-SERIES
The manufacturer is not liable for damage caused by the incorrect use or
incorrect installation of the dimmer.
The warranty period is 2 years from the
date of purchase, to be proven to the retailer by means of your purchase receipt.
Keep this manual in a safe place in case it is needed for (re)installation!
TRADIM Aalsbergen 15, 6942 SE Didam, The Netherlands www.tradim.nl
Version 2.0 ENG (25/01/19)
De fabrikant en/of leverancier is niet aansprakelijk voor schade veroorzaakt door verkeerd gebruik of
onjuiste installatie van de dimmer. De garantietermijn is 2 jaar vanaf de aankoopdatum, aan te tonen
door de dealer op uw aankoopbon. Version NL 3.0 (07/10/21). Bewaar deze handleiding goed voor (her)installatie!
TRADIM – Aalsbergen 9, 6942SE – Didam (NL) – www.tradim.nl
3107X-SERIES
GEBRUIKSAANWIJZING VLOERDIMMER 3107X-SERIE
INSTALLATIE:
• Schakel voor het installeren altijd eerst de stroom uit!
• Schroef de behuizing open neem de bovenzijde af
• Strip de voedingsdraden en sluit ze aan volgens de tekening
• Plaats de bovenzijde terug en zorg dat de mantel van de kabel
goed vastgeklemd zitten onder de trekontlasting
• Draai de schroeven aan de onderzijde vast

INSTRUCTION MANUAL FLOOR DIMMER 31070-SERIES
This floor dimmer is only suitable for low-voltage halogen lamps
(12V 35-150W). The 230V-12V transformer is integrated into this floor
dimmer (no external transformer required). Use only indoors.
INSTALLATION:
• Always switch off the power before installation!
• Unscrew the housing and remove the top side.
• Strip the power wires and connect them following the drawing.
• Put back the top side and make sure the wires are securely
clamped underneath the tension relief.
• Tighten the screws on the bottom.
31070-SERIES
The manufacturer is not liable for damage caused by the incorrect use or
incorrect installation of the dimmer.
The warranty period is 2 years from the
date of purchase, to be proven to the retailer by means of your purchase receipt.
Keep this manual in a safe place in case it is needed for (re)installation!
TRADIM Aalsbergen 9, 6942 SE Didam, The Netherlands www.tradim.nl
Version 2.0 ENG (25/01/19)
INSTRUCTION MANUAL FLOOR DIMMER 31070-SERIES
This floor dimmer is only suitable for low-voltage halogen lamps
(12V 35-150W). The 230V-12V transformer is integrated into this floor
dimmer (no external transformer required). Use only indoors.
INSTALLATION:
• Always switch off the power before installation!
• Unscrew the housing and remove the top side.
• Strip the power wires and connect them following the drawing.
• Put back the top side and make sure the wires are securely
clamped underneath the tension relief.
• Tighten the screws on the bottom.
31070-SERIES
The manufacturer is not liable for damage caused by the incorrect use or
incorrect installation of the dimmer.
The warranty period is 2 years from the
date of purchase, to be proven to the retailer by means of your purchase receipt.
Keep this manual in a safe place in case it is needed for (re)installation!
TRADIM Aalsbergen 9, 6942 SE Didam, The Netherlands www.tradim.nl
Version 2.0 ENG (25/01/19)
The manufacturer and/or supplier is not liable for damage caused by misuse or improper installation
of the dimmer. The warranty period is 2 years from the date of purchase, to be demonstrated
by the dealership on your purchase receipt. Version EN 3.0 (07/10/21). Keep this manual safe for (re)installation!
TRADIM – Aalsbergen 9, 6942SE – Didam (NL) – www.tradim.nl
3107X-SERIES
INSTRUCTION MANUAL FLOOR DIMMER 3107X-SERIES
INSTALLATION:
• Always switch off the power before installation!
• Unscrew the housing and remove the top side.
• Strip the power wires and connect them following the drawing.
• Put back the top side and make sure the sheath of the cable
are securely clamped underneath the tension relief.
• Tighten the screws on the bottom.