TRAK RACER TRX-BLK User manual

1
Published 2023‑10‑10
TRX
Assembly Guide
TRX-BLK & TRX-ALP
IMPORTANT: As there are different versions of each rig depending on your
region, please ensure that you are using the correct instruction set. The
part number below should match the part number labeled on your box

3 Symbol Legend
4 Part list
7 Assembly Notes
8 TRX Assembly Instructions
16 Wheel Mounting Options
17 Wheel Mount OPTION 1: Universal Mount
24 Wheel Mount OPTION 2: Direct Drive Mount
31 Wheel Mount OPTION 3: Fanatec DD1 / DD2
33 Wheel Mount OPTION 2: Fanatec CSL DD
39 OPTIONAL: TRX-SEAT
42 OPTIONAL: TRX Shifter Mount
44 OPTIONAL: TRX Monitor Stand
50 OPTIONAL: Vesa Mount Extension Arms
52 OPTIONAL: Locking Wheels
2
TABLE OF CONTENTS

3
Two people needed
Tighten hardware
Leave hardware loose for adjustment
Make Adjustment
Break tab off Corner bracket CB1
Safety glasses needed
Attention / Priority
Reserve for following step
Mirrored Components (Same on both sides)
IMPORTANT: As there are different versions of each rig depending on your
region, please ensure that you are using the correct instruction set. The
part number below should match the part number labeled on your box
IMPORTANT: Due to the nature of cut aluminium prole, some metal
shavings may still be present after our extensive QA cleaning process. We
recommend that boxes and packaging is opened on a hard oor.
NOTE: Some screws and washers are pre-installed and will need to be
loosened and reattached according to the instructions.

4
*NOTE: Extra hardware may be included as spare parts
TRX PARTS LIST
TRX-WLB x1
Wheel Tilt (Left)
TRX-WRB x1
Wheel Tilt (Right)
TRX-LB x1
Frame Front (Left)
TRX-RB x1
Frame Front (Right)
TRX-TVSP x1
Monitor Stand Strut
TRX-SWP x1
Wheel Mount Part 2
M6x10mm SF-M6-10 x2
M8x16mm
SH-M8-16 x4
M8x16mm
SB-M8-16 x4
WF-M8 x10
NF-M8 x4
NC-M6 x6
RC-M5 x2
WL-M8 x10
M6x10mm SB-M6-10 x8
M8x30mm
SH-M8-30 x4
SB-M8-30 x2
M8x30mm
BOX #: TRX-BLK-PART1
tooltip
INCLUDED TOOLS
5mm Hex Key
4mm Hex Key
6mm Hex Key
13mm-15mm Spanner
NOTE: Some screws and washers come pre-installed. These will be part of the parts
list and will need to be removed and reattached according to the instructions.
SL-M8-16 x2
M8x35mm
SB-M8-35 x2
M8x40mm
SB-M8-40 x2

5
TRX PARTS LIST
TRX-TB x1
Pedal Assembly
TRX-WLAP x1
Wheel Mount Part 2 (Right)
TRX-WRAP x1
Wheel Mount Part 2 (Left)
TRX-SPL x1
Seat Bracket (Left)
TRX-SPR x1
Seat Bracket (Right)
TRX-SLIDER x2
Seat / Pedal Slider
TRX-SWRL x1
Frame Front (Right)
TRX-BA x1
Frame Rear
TRX-LH x2
Frame Collar
TRX-KNOB12 2
12mm Knob Screw
TRX-KNOB14 x4
14mm Knob Screw
TRX-KNOB19 x2
19mm Knob Screw
19
BOX #: TRX-BLK-PART2 BOX #: TRX-BLK-PART3
*NOTE: Extra hardware may be included as spare parts
TRX-KNOB24 x2
24mm Knob Screw
2424
TRX-BUSH5 x4
Bushing, 5mm
NOTE: Some screws and washers come pre-installed and will need to be removed
and reattached according to the instructions.
TRX-BUSH10 x4
Bushing, 10mm
TRX-BUSH15 x4
Bushing, 15mm

6
1
NOTE
PEDAL MOUNT
INSIDE
TOP SIDE
FRONT SIDE
OUTSIDE
MONITOR BRACE
BACK SIDE
SHIFTER
SEAT PLATFORM
tooltip
SHIFTER MOUNT
MONITOR STAND STRUT
a
a
a
x
x
x
INSTALLATAION ORDER FOR SCREWS & WASHERS HOW TO MEASURE SCREWS
①SCREW ②LOCK WASHER
(IF APPLICABLE)
③WASHER
FLAT SCREW
HEX SCREW
BUTTON SCREW

tooltip
tooltip
tooltip
TRX-BA x1
7
1NOTE: Some screws and washers come pre-installed and will need to be loosened
and reattached according to the instructions.
Slightly loosen the
two knob screws
located at the back
of the seat platform
Turn the T-handle at the rear in
either direction until the locking
pins unseat from their holes and lift
the top plate to the top “G” position
Once the locking pins
are re-seated into the
top holes with a “click”,
tighten the knob screws
to lock the platform
a
b
c

8
2
tooltip
Remove the seat
platform assembly by
removing the 4 screws
and set everything aside
tooltip
TRX-BA x1

tooltip
tooltip
tooltip
9
3
a
b
c
NOTE: Some screws and washers come pre-installed
and will need to be removed and reattached according
to the instructions.
TRX-SLIDER x1
M8x16mm
SH-M8-16 x4 WL-M8 x4
Fit tabs into holes of one
side of the handlebar, then
squeeze handlebar and
repeat for opposite side

tooltip
NOTE: Some screws and washers come pre-installed and will need to be loosened
and reattached according to the instructions.
tooltip
10
4
Reattach the
seat platform to
the seat slider
M8x16mm
SH-M8-16 x4 WF-M8 x4
5NOTE: If the locking seat platform locking mechanism
are loose, tighten the eyelets on both sides by holding
the centre turnbuckle and tighten accordingly.
DO NOT OVERTIGHTEN
HOLD
HERE

tooltip
11
Slightly loosen the two set
screws pre-installed in TRX-LH
and slide over TRX-RB.
Keep screws loose until STEP 18
a
b
6
TRX-LH x1
Remove pre-installed
SB-M8-15 screws
TRX-RB x1
NOTE: Some screws and washers come pre-installed and will need to be loosened
and reattached according to the instructions.

tooltip
NOTE: Some screws and washers come pre-installed and will need to be loosened
and reattached according to the instructions.
tooltip
12
7
M8x15mm
SB-M8-15 x6
TRX-RB x1
a
b
Reinstall and keep screws
slightly loose until STEP 17
WC-M8 x6

Remove pre-installed
SB-M8-15 screws
13
8
TRX-LB x1 TRX-LH x1
tooltip
Slightly loosen the two set
screws pre-installed in TRX-LH
and slide over TRX-RB.
Keep screws loose until STEP 18
a
b
NOTE: Some screws and washers come pre-installed and will need to be loosened
and reattached according to the instructions.

14
9
tooltip
tooltip
M8x15mm
SB-M8-15 x6
a
b
TRX-LB x1
Reinstall and keep screws
slightly loose until STEP 17
WC-M8 x6
NOTE: Some screws and washers come pre-installed and will need to be loosened
and reattached according to the instructions.

tooltip
NOTE: Some screws and washers come pre-installed and will need to be loosened
and reattached according to the instructions.
tooltip
tooltip
15
M8x16mm
SH-M8-16 x12
a
c
b
TRX-TB x1
Keep screws slightly
loose until STEP 19
10
Remove pre-installed
SH-M8-16 screws (x12)
& WF-M8 (12)
Re-install SH-M8-16
& WF-M8
WF-M8 x12

tooltip
16
NOTE
WM-WM6 (TR80-NWM6)
Wheel Mounting Plate (Over-sized)
Option 1:
Page 17
WM-DD (TR80-NWMDD)
Wheel Mounting, Direct Drive
Option 2:
Page 24
Please skip to the pages corresponding to the wheelbase mounting method you have chosen for your TRX rig
For all other wheel mounting methods, please contact customer support.
FANATEC CSL DD
Side Mount
Option 4:
Page 23
FANATEC PODIUM DD1 / DD2
Side Mount
Option 3:
Page 23

17
Published 2023‑10‑10
OPTION 1:
Universal Wheel Mount
TR-80-NWM6
*NOTE: Extra hardware may be included as spare parts
Part # Image Description QTY Check
WM-NWM6 Wheel Mount, Universal Oversize 1
WM6-TILT-L NWM6 Tilt (Left) 1
WM6-TILT-R NWM6 Tilt (Right) 1
TRX-KNOB8 8mm Knob Screw 2
TRX-KNOB12 12mm Knob Screw 2
SB-M8-20 Screw (Button), M8 x 20mm 2
WL-M8 Washer (Lock), M8 2
SF-M6-16 Screw (Flat), M6 x 16mm 8
RC-M5 Retainer Clip, M5 2
8

tooltip
tooltip
18
11 NOTE: Some screws and washers come pre-installed. These will be part of the parts
list and will need to be removed and reattached according to the instructions.
WM6-TILT-L x1 WM6-TILT-R x1
a
b
NOTE: Due to the slider blocks
being made of aluminum, be
cautious to not cross-thread
when tightening screws
M6x16mm
SF-M6-16 x8

tooltip
19
12
RC-M5 x2 TRX-WLAP x1
tooltip
X2
a
b
X2
Press RC-M5 into
groove of TRX-KNOB12
after threading in.
TRX-SWP x1 TRX-KNOB12 x2

tooltip
20
13 NOTE: TR-SWRL is an assembly rod used to maintain alignment of your wheel mount.
It will not add rigidity. This part can be removed if it impedes with your wheel base.
tooltip
a
b
Press RC-M5 into
groove of TRX-KNOB12
after threading in.
X2
X2
TRX-KNOB12 x2 TRX-SWP x1 TRX-WRAP x1 RC-M5 x2