Trane 4MYW5-A User guide

,QVWDOOHU¶V0DQXDO
$SULO 2010 06691$(1
16~18 SEER Inverter Unit
4
4MYW5-A
4MXW5-A
4TYK5-A
4TXK5-A
+]

Warnings and Cautions
© 20 rane All rights reserved
Warnings and Cautions. Notice that warnings and cautions appear at appropriate intervals
throughout this manual. Warnings are provided to alert installing contractors to potential
hazards that could result in personal injury or death, while cautions are designed to alert
personnel to conditions that could result in equipment damage.
Your personal safety and the proper operation of this machine depend upon the strict
observance of these precautions.
Trane has always recommended installing Trane approved matched indoor and outdoor
systems.
The benefits of installing approved matched systems are maximum efficiency, optimum
performance and best overall system reliability.
WARNING
This equipment is to be serviced by professionally trained personnel ONLY. Under NO
circumstances should an unqualified person service it. This equipment contains
refrigerant under PRESSURE and operates at HIGH VOLTAGE. Improperly installed,
adjusted or altered equipment by an unqualified person poses safety hazards
including FIRE, ELECTROCUTION, or EXPLOSION, which could result in death or
serious injury.
WARNING
Electrocution and Fire Hazards with Improperly Installed and Grounded
Field Wiring!
Improperly installed and grounded field wiring poses FIRE & ELECTROCUTION
hazards. To avoid these hazards, you MUST follow requirements for field wiring
installation and grounding as described in the National Electrical Codes (NEC) and
your local/state electrical codes. All field wiring MUST be performed by qualified
personnel.
Failure to follow these requirements could result in death or serious injury.
Attention:Warnings and Cautions appear at appropriate sections throughout this
literature. Read these carefully.
WARNING:Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION:Indicates a potentially hazardous situation which, if not avoided, could
result in minor or moderate injury. It may also be used to alert against unsafe practices.
NOTICE:Indicates a situation that could result in equipment or property-damage only
accidents.
10 T MS-SVN22A-EN

Preface
3
WARNING
R410A Refrigerant under Higher Pressure than R22!
The units described in this manual use R410A refrigerant which operates at 50 to 70%
higher pressures than R-22. Use only R-410A approved service equipment. Refrigerant
cylinders are painted with "pink" color to indicate the type of refrigerant and may
contain a "dip" tube to allow for charging of liquid refrigerant into the system. For
specific handling concerns with R-410A, please contact your local Trane representative.
Failure to use R-410A approved service equipment could result in standard equipment
exploding under R-410A higher pressure which could result in death or serious injury.
NOTICE
Use PVE Oil with R-410A Mini-Split Units!
All R-410A mini-splits use a PVE oil (Polyvinyl Ether Oil) that readily absorbs moisture
from the atmosphere. To limit this “hygroscopic” action, the system should remain
sealed whenever possible. If a system has been open to the atmosphere for more than
4 hours, the compressor oil must be replaced. Never break a vacuum with air and
always change the driers when opening the system for component replacement. For
specific handling concerns with PVE oil, contact your local Trane representative.
USE ONLY THE FACTORY RECOMMENDED - DAFNE HERMETIC OIL FV50S - for
servicing these units.
Important!
Environmental Concerns
Scientific research has shown that certain man-made chemicals can affect the earth’s naturally
occurring stratospheric ozone layer when released to the atmosphere. In particular, several of
the identified chemicals that may affect the ozone layer are refrigerants that contain Chlorine,
Fluorine and Carbon (CFCs) and those containing Hydrogen, Chlorine, Fluorine and Carbon
(HCFCs). Not all refrigerants containing these compounds have the same potential impact to the
environment. Trane advocates the responsible handling of all refrigerants—including industry
replacements for CFCs such as HCFCs and HFCs.
Responsible Refrigerant Practices
Trane believes that responsible refrigerant practices are important to the environment, our
customers, and the air conditioning industry. All technicians who handle refrigerants must be
certified. The Federal Clean Air Act (Section 608) sets forth the requirements for handling,
reclaiming, recovering and recycling of certain refrigerants and the equipment that is used in
these service procedures. In addition, some states or municipalities may have additional
requirements that must also be adhered to for responsible management of refrigerants. Know
the applicable laws and follow them.
MS-SVN22A-EN


*HQHUDO,QIRUPDWLRQ  
$FFHVVRULHV  
7\SLFDO,QVWDOODWLRQ  
,QVWDOODWLRQORFDWLRQ  
,QGRRU8QLW  
2XWGRRUXQLW  
,QVWDOODWLRQ  
,QGRRU8QLW,QVWDOODWLRQ  
,QVWDOOLQJ2XWGRRU8QLW 

2XWGRRUFRQGHQVDWLRQGUDLQDJH+HDWSXPSW\SHRQO\ 
&KHFNDIWHU,QVWDOODWLRQDQG7HVW2SHUDWLRQ 
:LULQJ'LDJUDPV 
+LJK(IILFLHQF\+]PRGHOV 
&RQWHQWV

9DFXXP3XPSDQG/HDN,QVSHFWLRQ
066912$(1
&RQQHFWLRQ3LSH
 20

5
This installation Manual is given as a guide to good practices in the installation and operation of a
wall mounted split system models and
Read these operation Instructions completely before installing the unit.
Warranty
Warranty is based on the general terms and conditions by country. The warranty is void if the
equipment is modified or repaired without the written approval of The Trane Company, if the
operating limits are exceeded or if the control system or the electrical wiring is modified.
Damage due to inappropriate installation, lack of knowledge or failure to comply with the
manufacturer’s instructions, is not covered by the warranty obligation.
If the installation does not conform to the rules described in Installation Manual, it may entail
cancellation of warranty and liabilities by The Trane Company.
Reception
On arrival, inspect the unit before signing the delivery note. Specify any damage of the unit on
the delivery note, and send a registered letter of protest to the last carrier of the goods within 72
hours of delivery. Notify the dealer at the same time.
The unit should be totally inspected within 7 days of delivery. If any concealed damage is
discovered, send a registered letter of protest to the carrier within 7 days of delivery and notify
the local dealer.
About the Unit
These units are assembled, pressure tested, dehydrated, charged and run tested before shipment.
This manual contains informations related to
Refrigerant
The refrigerant provided by the manufacturer comply with all the requirements for our units.
When using a recycled or reprocessed refrigerant, we recommend its qualities be as good as
those of a new refrigerant. It is necessary to have the refrigerant tested by a qualified laboratory.
Failure to do so could void the warranty.
Important
These instructions do not cover all variations in systems, nor do they provide for every possible
contingency to be met in connection with installation. Should further information be desired or
should particular problems arise which are not covered sufficiently in this manual, the matter
should be referred to your authorized Trane dealer.
General Information
4MYW54TYK5
4MYW54TYK5;
and
; 4MXW5 and 4TXK5. However it does not
contain all the service procedures for this unit, as these procedures must be performed by a qualified
service technician, through the maintenance contract with a reputable service company.
MS-SVN22A-EN
4MXW5 and 4TXK5 .


$FFHVVRULHV
7DEOH 3DUWVOLVW
1R 3DUW1DPH 'LDJUDP 4W\ 6SHFLILFDWLRQ 0HPR
 0RXQWLQJSODWH 
:LUHOHVVUHPRWH
FRQWUROOHU 
5HPRWHFRQWUROOHU
KROGHU 
 %DWWHU\  $$$9
 7DSSLQJVFUHZ 0~ 67; )RUPRXQWLQJSODWH
 'UDLQKRVH  / P
 7KHUPDOLQVXODWLRQ 
 'UDLQNLW  +HDWSXPSW\SHRQO\
 'UDLQKROHFRYHU  +HDWSXPSW\SHRQO\
 $LUFOHDQHU 
 $LUILOWHU 
066912$(1


,QGRRUXQLW
$LULQ
$LURXW
2XWGRRUXQLW
3RZHUFDEOHˆ
5HPRWHFRQWURO
)URQWSDQHO
)LOWHU
*XLGHORXYHU
:DOO SLSH
%LQGWDSH
'UDLQDJHSLSH
21
2))
$LURXW
$LULQ
ˆ7REHSURYLGHGDWILHOG

8
Indoor Unit
WARNING
Adequate Support!
Wall structure must be adequate to support the weight of the unit. Failure to ensure
adequate structural support could result in unit falling from its location which could
result in death, serious injury, or equipement or property-only damage.
1. The air inlet and outlet should be far away from anything that could prevent the air from
reaching all parts of the room.
2. Select a location where it is easy to drain the condensing water and connect to the outdoor
unit;
3. Keep the indoor unit far away from heat sources, vapor and inflammable gas;
4. Be sure that the installation of the indoor unit conforms to the installation dimension
diagram;
5. Be sure to leave enough space to allow access for routine maintenance; clearance between
the indoor unit and the floor should
6. Install in a location where the ay from other electric appliances
such as television, audio devices etc.;
7. Select location where air filters can be easily removed
Outdoor unit
WARNING
Adequate Support!
Wall structure must be adequate to support the weight of the unit. Failure to ensure
adequate structural support could result in unit falling from its location which could
result in death, serious injury, or equipement or property-only damage.
1. Select a location from which noise and air discharge by unit will not annoy neighbors.
2. Select a location where there is sufficient ventilation.
3. Make sure the air inlet and outlet are not blocked by any obstacles.
4. Select a location capable of supporting the weight and vibration of the outdoor unit, and
where installation work can be carried out safely.
5. Select a location away from flammable gas or gas leaks.
6. Make sure that the installation of the outdoor unit conforms to the installation dimension
diagram.
NOTICE
Installing the unit in one of the following locations could result in unit malfunction:
• Places where oil (machine oil) is used
• Seaside/places with high level of salt in the air.
• Places with high level of sulfur gas such as areas with hot springs.
• Places where high-frequency waves are generated by radio equipment, welders and medical
equipment.
• Other unusual places where unit operation may be altered.
Installation location
MS-SVN22A-EN
be more than 7 feet.
unit is more than 3 feet aw

9
Indoor Unit Installation
WARNING
Hazardous Service Procedures!
The maintenance and troubleshooting procedures recommended in this section of the
manual could result in exposure to electrical, mechanical or other potential safety
hazards. Always refer to the safety warnings provided throughout this manual
concerning these procedures. When possible, disconnect all electrical power including
remote disconnect and discharge all energy storing devices such as capacitors before
servicing. Follow proper lockout/tagout procedures to ensure the power can not be
inadvertently energized. When necessary to work with live electrical components, have
a qualified licensed electrician or other individual who has been trained in handling live
electrical components perform these tasks. Failure to follow all of the recommended
safety warnings provided, could result in death or serious injury.
Mounting Location
1. Always mount the rear panel horizontally.
2. Fix the rear panel on the selected location
3. Be sure that the rear panel has been fixed firmly enough to withstand the weight of an adult
thermore, the weight should be evenly shared by each screw.
Drilling a hole in the wall to install the piping
The piping can be connected in six different locations on the unit, as shown on figure below:
1. Drill a 65mm diameter hole in the wall at a slight downward angle toward the outdoor side in
such a way that the end of the pipe outside is 5 mm lower than the inside.
2. Insert a sleeve into the hole to prevent the connection piping and wiring from being damaged
when passing through the hole.
Installation
Left downward
Left
Rear Left
Right Downward
Rear Right
Right
MS-SVN22A-EN
of 140lbs,fur

10
Installation
NOTICE
When a wall sleeve is not used, it is then necessary to drill a straight hole in the wall. If
the hole is not straight and uniform, this could result in water leaking from
condensation, resulting in property damage.
NOTICE
If a wall sleeve is not mounted in the wall, the wiring between the indoor unit and the
outdoor unit can possibly be damaged resulting in electrical current loss in the ground
wiring.
Installing the water drain pipe
NOTICE
Do not wrench or bend the drain hose and make sure the ends of the drain pipe are not
under water. Failure to do so could result in leakage.
1. To ensure proper water drainage, the drain hose should be placed at a downward slant.
2. The water drain pipe must be insulated throughout the house.
Installing the unit
Note: The piping can be lead out from right, right rear, left, left rear.
1. When routing the piping and wiring from the left or right side of indoor unit, cut off the
tailings from the chassis in necessary.
(1).Cut off the tailings 1 when routing the wiring only;
(2).Cut off the tailings 1 and tailings 2 when routing both the wiring and piping.(or 1,2,3)
Under water
Bent
Wrenched
MS-SVN22A-EN
sleeve