Trane TR200 Series Manual

TRANE TR200 Drive Startup
Startup Procedures

Objectives
Student will be able to:
• Identify the reference material needed for a startup and
where that material may be found
• Safely apply power to the drive
• Navigate the LCP, and display basic programming skills
• Identify the different terminal blocks on the drive
• Connect control wiring for various control schemes used in
HVAC applications
• Safely check motor rotation and operation
• Copy parameter settings to LCP

Specific instruction manual (IM) shipped with each drive
Programming guide & other documentation available for download
Reference Material

• Safety
• Technical data
• Dimensions
• Installation
• Operation
• Programming
• Alarm and warning messages
• Examples of use
• List of different functions and drive options
Instruction Manual Contents

Touching the electrical parts may be fatal — even after the
equipment has been disconnected from the AC line. To be
sure that the capacitors have fully discharged, you may
have to wait up to 40 minutes.
DANGER
!

•BE AWARE OF THE HAZARD
•BE TRAINED ON ARC FLASH
•USE PROPER TEST & PROTECTIVE EQUIPMENT
ARC FLASH WARNING

Applying Power
• Double check to ensure all wiring is correct
• Measure line voltage to be applied to the input side of the
VLT unit (terminals L1, L2 and L3) to verify it is within +/-
10% of the rated input voltage
• Ensure fuses are correct and in place
• Ensure all run and speed commands are off or at zero
• Power is ready to be switched on

LCP Features
Graphical display
• Shows bars and
graphs
• Displays international
symbols
• 27 languages
available
Menu structure
• Based on matrix system
• Easy shortcuts
• Edit and operate in
different setups
simultaneously
Other benefits
• Removable during
operation
• Up/download from
one drive to another
• IP65 rating when
mounted in panel door
• Numerical display
available
LED indicators
Quick menus
• Choose from Danfoss
or personalized quick
menus
• Application setup
menus
Special keys
• Info (on board manual)
• Cancel (undo)
• Alarm log (quick access)

Status Modes
Display up to 4 variables
Display up to 5 variables Display the smart logic controller
Toggled with status key

Info Key
• Parameter descriptions
• Onboard manual
• Press the key when in the alarm log for information
• Press the key when displaying the “Status” screen
to show the display layout

Cancel Key & Back Key
• Pressing the “Cancel” Key will undo the change to a
parameter that was just made.
• Pressing the “Back” Key will undo the change to a
parameter that was just made.

• Alarm Log shows the last 10 alarms
Easy, one-key access to
the Alarm Log
Alarm Log Key

• Operating time
• Report value
• External reference
• Frequency
• Current
• Voltage
• DC link
Alarm Log Data

Resetting “Trip” & “Triplock” Alarms
• Pressing the “Reset” key during a “Trip” alarm condition
will clear the alarm
• “Triplock” alarms can only be reset after cycling input
power
• Parameter 14-20/14-21 enables/disables automatic reset

There are 3 different ways to control the drive
1 – Local control or “Hand Mode” using the LCP
2 – Remote control using remote I/O signals (digital & analog)
3 – Remote control using various serial communication protocols
Controlling the VFD

Hand On Key
• Starts drive by hand; one jumper wire is needed
• Keypad accepts local reference in RPM or Hz

Auto On Key
• Run the drive with remote control
• Open or closed loop
• Start command & speed referenced needed
• Drive status display

LCP Copy
• Set parameter 0-50 to “All
to LCP” to load your setup
from the drive into the LCP
memory
• Copy process initiates
upon pressing “OK” key
• Select “All from LCP” to
copy settings back from
the LCP into the drive

Keypad Lock
• Setup parameters for locking
the keypad in the 0-6
parameter group
• Limit access to Main Menu
and or Personal Menus
• Can be temporarily bypassed

LCP Menu Navigation
Use the arrow keys to scroll through the menus: