Trane ZSENS930AW00MA Assembly instructions

Z-Wave™ Temperature & Humidity Sensor
ZSENS930AW00MA Installer Guide
This sensor should be installed by a qualified HVAC technician.
After installation, allow 10 minutes for the temperature readings to stabilize.
NOTE:This document is intended for use with software version 5.4 or newer when using this sensor with a Trane®or American Standard®connected thermostat (824/850/1050).
INSTALLATION – adding a ZSENS930 to a new or existing Z-Wave network
STEP 1 – Find the right location
Suggested criteria for finding the right sensor location when used to control a home or as a
thermostat sensor:
1. Do not place near a supply register.
2. Do not place near windows or on an exterior wall.
3. Do not place behind doors or where air flow can be blocked by furniture.
4. Do not place where it may be subject to unnecessary or extreme temperature changes;
unintended influences may cause adverse environment sensing.
5. The optimum zone for correct placement of the sensor is at least 5 feet above the floor
and at least 2 feet below the ceiling.
STEP 2 – Remove the Back Plate
Insert a small screwdriver beneath the tab at the bottom of the Back Plate and lift to unsnap
it from the front. WRITE DOWN the Serial Number from the Back Plate of the sensor.
STEP 3 – Insert the supplied batteries
Two 1.5 Volt AAA batteries are supplied in the box.
Please see Table 1. on Page-2 to continue with adding a wireless sensor
to the 824, 850 and 1050 thermostats.
STEP 4 – Put the Z-Wave bridge in Add mode
Press the +or Add button on the bridge.
STEP 5 – Add the sensor
Stand where the sensor is to be installed and press and release the button labeled
“INSTALL” on the interior of the sensor
STEP 6 – Connection Status.
The status LED next to the button on the interior of the sensor will blink rapidly for 3
seconds when it has been added to your Z-Wave network.
STEP 7 – Mount the back plate at the right location
Anchors and screws are provided to mount the Back Plate.
STEP 8 – Mount the Sensor FINAL INSTALLATION STEP
Once successfully added, snap the sensor onto the mounted Back Plate.
It will take 10 minutes after installation for the temperature and humidity values to stabilize
due to handling.
Top
Battery
Compartment
Bottom
Tab
Slot
INSTALL
Button
Status
LED
Front
Plate
Back
Plate
Tab
Top
Serial Number
Location
Scan the QR code to view help videos
SERIAL#
LOCATION Or zone name if applicable
Home owner should retain a copy of this document for their records.
ZONE NOTES:
LOCATION: LOCATION / :
SERIAL# SERIAL#
LOCATION: LOCATION:
SERIAL# SERIAL#
LOCATION: LOCATION:
SERIAL# SERIAL#
LOCATION: LOCATION:
SERIAL# SERIAL#
NOTE : Please see this link for video tutorials:
http://www.fieldtechhelp.com/NEWURLNEEDED.html
A QR Code at the top of this document is also available for your convenience.The latest version of this document can be found on ComfortSite or ASDealernet.
Sensor with lowest battery level is shown on home screen.
Full BatteryFull Battery
Replace BatteryReplace Battery
Low BatteryLow Battery
Sensor is offlineSensor is offline
Page - 1

Table 1. ADDING A ZSENS930
FIRST, FOLLOW STEPS ONE THROUGH THREE IN THE INSTALLATION TABLE.
S T E P 4.1
Access the “Service Menu”
STEP 4.2
Put the stat in “Add” mode
STEP 4.3
Add the Z-Wave sensor
STEP 4.4
On screen response
Action Select
“Indoor Sensor Setup”
Select “Wireless Sensor”
and then on the next
screen select “Add”
Stand where the sensor is to be
installed and press and release the
button labeled “INSTALL” on the
interior of the sensor.
Text at top of the screen should change:
From: “
Waiting to Add Device – Press and Hold to Cancel “
To: “Adding Device”
Button
To
The STATUS LED will blink rapidly
for 3 seconds
After the sensor is added, “Temperature Sensor added as Device [X]:
Sensor added successfully.” should appear.
Page - 2
Table 2. ASSIGNING A ZSENS930
FIRST, FOLLOW STEPS 1THROUGH 3IN THE INSTALLATION TABLE
ON PAGE 1 AND ALL THE STEPS IN TABLE 1.
S T E P 5.1
Select an
available
sensor
Select the newly added sensor on the right side of the Sensor Assignment screen
under the label “Available Sensors”.
NOTE: The selected sensor will be highlighted in blue.
Screen 1
STEP 5.2
Assign the
sensor
Once the sensor is selected “Assign” will illuminate
on the Navigation Bar. Select “Assign”.
Repeat until all needed sensors are assigned.
STEP 5.3
Sensor
is now
assigned.
The list of assigned and averaged sensors on the left is now updated and the
previously unassigned sensor is now included. (Screen 2)
Screen 2
STEP 5.4 Select “Done” to save and exit the Indoor
Sensor Setup screen.
After this step follow
Step 7 and 8from Page-1
if not already complete
NOTE: By default all sensors in the Assigned list are
averaged together evenly. Up to four sensors may be used
to define the temperature of the conditioned space.
Table 3.
UNASSIGNING A ZSENS930
STEP 1
Select an
assigned
sensor
Select the sensor to be removed from the assigned sensor list. Use the serial
number to verify the device is the correct sensor.
NOTE: The selected sensor will be highlighted in blue.
Screen 3
STEP 2
Unassign
the sensor
Once an assigned sensor is selected “Assign” will change to
”Unassign” on the Navigation Bar.
Select “Unassign”.
STEP 3
Sensor
is now
unassigned.
The list of assigned and averaged sensors is now updated and the previously
asssigned sensor is moved to the “Available Sensors” list. (Screen 4)
NOTE: The order of sensors does not matter. By default the temperature values
from all sensors are averaged together evenly to determine the temperature of
the conditioned space.
Screen 4
STEP 4 Select “Done” to save and exit the
Indoor Sensor Setup screen.
NOTE: The thermostat will not allow you to exit this screen without at least one
sensor assigned to the system.

SUMMARY OF SENSOR OPERATION
INSTALL BUTTON – Function Overview
• Press once to add or remove the sensor from a Z-Wave Network.
• Press and hold, approximately 10 seconds, until the STATUS LED starts
blinking to restore factory defaults.
• Press three times rapidly to send a “BATTERY_REPORT” and
“WAKE_UP_NOTIFICATION” (if installed on a network).
The sensor will stay awake for 30 seconds.
STATUS LED – Function following a button press:
The LED will give an indication for 30 seconds following a button press. In that
time the following will be seen:
• Continuous On: Device is enrolled on a Z-Wave Network.
• Slow Blinking: Device is not enrolled on a Z-Wave Network.
• Fast Blinking: Successfully added to or removed from a Z-Wave network.
ADD – Adding the sensor to an existing Z-Wave network
1. Set your home’s Z-Wave Bridge into ADD Mode.
2. Press and release the INSTALL button on the sensor.
3. The Status LED will blink rapidly for 3 seconds when it has been added to
your Z-Wave network. Your bridge will also indicate that the sensor was
successfully added.
REMOVE – Removing the sensor from a Z-Wave network
1. Set your home’s Z-Wave Bridge into REMOVE Mode.
2. Press and release the INSTALL button on the sensor.
3. The Status LED will blink rapidly for 3 seconds when it has been removed
from your Z-Wave network. Your bridge will also indicate that the sensor
was successfully removed.
TROUBLESHOOTING
SYMPTOM CAUSE CURE
Sensor fails
to add to
the network.
(slow blinking
of the Status
LED & no
pairing action
seen on the
bridge)
Out of range
Add a Z-Wave repeating device (e.g. light
module/dimmer) at a location between the bridge
and sensor. First add the repeater to the network
following that device’s instructions. Then try
to add the sensor to the network again at the
desired sensing location.
Improperly
removed
from network
previously.
Remove the sensor from the network, follow the
steps in Table 3. Then add it back to the network.
Sensor drops
connection
intermittently
Edge of
range
Add a Z-Wave repeating device (e.g. light
module/dimmer) at a location between the bridge
and sensor.
Button press
ignored
Button press
too fast or too
slow
Firm 1/2 second button press.
Sensor
goes from
“Online” to
“Offline”and
“Missing
Sensor”
alarm
TSO.001.00
is shown
Sensor is
enabled but
offline (not
reporting).
Change the batteries in the sensor.
Remove the offline sensor following the steps
from Table 3 then reinstall or add a new sensor.
Add a signal repeater.
“Low Battery”
alarm
TSO.004.00
Sensor is
reporting a
low battery.
Change the batteries in the sensor.
FACTORY RESET
Factory Reset should be used only when the primary controller is missing or
otherwise inoperable. Press and hold, approximately 10 seconds, until the Status
LED starts blinking.
** FOR INDOOR USE ONLY **
SPECIFICATIONS
SIZE (INCHES): 3.25 X 2.0 x 0.60 POWER: 2 X AAA Alkaline Batteries
WEIGHT: 0.25 LBS RF:
Z-WAVE ZM5202,US 908.4 MHz
/ 916 MHz
NOTE: This sensor can be added to any Z-Wave network. It can also be added to a Trane or American Standard connected thermostat with a built in Z-Wave bridge then assigned as
an indoor temperature sensor (IDT) from the Service Menu.
Table 4.
REMOVING A ZSENS930
NOTE: This will work for both “Offline” and “Online” sensors and only ZSENS930 sensors may be removed this way. The Summary Table will also work.
STEP 1
Unassign the sensor
STEP 2
Select the “Offline” sensor.
STEP 3
Remove the sensor
STEP 4
Screen change
Action
Follow steps 1
through 3in Table 3
for the sensor(s) that
are to be removed.
They must be
unassigned to be
removed.
Once the sensor is in the “Available Sensors” list,
select the "Wireless" button and then select the sensor
to be removed. Use the serial number to verify the
device is the correct sensor.
NOTE: The selected sensor will be highlighted in blue.
Tap the “Remove” button
NOTE: If the sensor is “Online” you will
need to press the “INSTALL” button on
the inside of the sensor while “Waiting to
Remove Device”.
Select “Done”. The sensor is no longer
included in the “Available Sensors” list.
(Screen 6)
NOTE: To return a sensor to the list you will
have to go through the steps of Table 1.
Screen 5 Screen 6
Page - 3

Page - 4
Z-WAVE CONFIGURATION TABLE
Parameter Description Length
(Bytes) R/W Default Value Valid Values
1 Time between Battery Reports (hours) 1 R/W 0 0 = Do not send periodically; Range: 1–127 hours
2 Send BASIC SET ON above this temperature (See #20) 1 R/W 121 121 = Disabled; Range: 15 – 120° F
3 Send BASIC SET ON below this temperature (See #20) 1 R/W 121 121 = Disabled; Range: 15 – 120° F
4 Send BASIC SET OFF above this temperature (See #20) 1 R/W 121 121 = Disabled; Range: 15 – 120° F
5 Send BASIC SET OFF below this temperature (See #20) 1 R/W 121 121 = Disabled; Range: 15 – 120° F
6 Send multiple attempts for all BASIC SET commands 1 R/W 0 0 = Disabled; 1-5 = Number of extra attempts sent every
minute after first send
7 Temperature Units 1 R/W 1 0 = Celsius; 1 = Fahrenheit
8 Association Group1 – Temperature delta auto send threshold 1 R/W 10 Range: 1 – 200; Parameter is in tenths of degrees.
9 Association Group1 – Periodic temperature send interval 1 R/W 0 0 = Disabled; Range: 1-120 minutes
10 Association Group2 – Temperature delta auto send threshold 1 R/W 10 0 = Disabled; Range: 1 – 50; Parameter is in tenths of
degrees.
11 Association Group2 – Periodic temperature send interval 1 R/W 0 0 = Disabled; Range: 1-120 minutes
12 Send BASIC SET ON above this humidity (See #20) 1 R/W 0 0 = Disabled; Range: 1–100%
13 Send BASIC SET ON below this humidity (See #20) 1 R/W 0 0 = Disabled; Range: 1-100%
14 Send BASIC SET OFF above this humidity (See #20) 1 R/W 0 0 = Disabled; Range: 1-100%
15 Send BASIC SET OFF below this humidity (See #20) 1 R/W 0 0 = Disabled; Range: 1-100%
16 Association Group1 – Humidity delta auto send threshold 1 R/W 5 Range: 1-50%
17 Association Group1 – Periodic humidity send interval 1 R/W 0 0 = Disabled; Range: 1-120 minutes
18 Association Group3 – Humidity delta auto send threshold 1 R/W 5 0 = Disabled; Range: 1-30%
19 Association Group3 – Periodic humidity send interval 1 R/W 0 0 = Disabled Range: 1-120 minutes
20 BASIC SET options for temperature and humidity 1 R/W 1
Configuration Register Combinations:
1 = Enable Registers 2, 5, 12 15
2 = Enable Registers 2, 5, 13, 14
3 = Enable Registers 3, 4, 12, 15
4 = Enable Registers 3, 4, 13, 14
21 Temperature Offset 1 R/W 0 Range: -7 to 7° F
22 Humidity Offset 1 R/W 0 Range: -7% to 7%
23 Humidity Filter Time Constant 1 R/W 30 Range: 0 - 60 minutes 0 = Disabled
ASSOCIATION GROUP INFORMATION TABLE
GROUP PROFILE COMMAND CLASSES GROUP NAME MAX DEVICES
1 Lifeline Battery Report, Multilevel Sensor Report, Device Reset
Locally Notification Lifeline 1
2 Sensor Multilevel Sensor Report Temperature Reports 5
3 Sensor Multilevel Sensor Report Humidity Reports 5
4 Sensor Basic Set Temperature Driven Basic Sets 5
5 Sensor Basic Set Humidity Driven Basic Sets 5
6 Sensor Battery Report Battery Reports 5
FCC/IC NOTICES
FCC ID: WIBTZW020 - This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,
and (2) This device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with
the limits for Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
IC ID: 9374A-W020 - This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne
doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’encompromettre le fonctionnement.
U.S.A. / Canada
[phone]
About Trane and American Standard Heating and Air Conditioning
Trane and American Standard create comfortable, energy efficient
indoor environments for residential applications. For more information,
please visit www.trane.com or www.americanstandardair.com
Representative-only illustrations included in this document.
The manufacturer has a policy of continuous data
improvement and it reserves the right to change design
and specifications without notice. We are committed to
using environmentally conscious print practices.
All trademarks referenced are the trademarks of their
respective owners. Z-Wave is a trademark of Z-Wave
Alliance. © 2021
18-HD83D1-5B-EN 26 Aug 2021
Supersedes 18-HD83D1-5A-EN (August 2020)
*
* Configurable through third party Z-Wave systems.