Transcend TS16GCF600 User manual

T
T
TS
S
S8
8
8G
G
G~
~
~1
1
16
6
6G
G
GC
C
CF
F
F6
6
60
0
00
0
0
600X CompactFlash Card
Transcend Information Inc.
V1.0
1
Description
Dedicated to fulfilling the demanding requirements of
performance-conscious photographers, Transcend
proudly releases its Extreme Plus 600X CompactFlash
cards with Turbo MLC technology. With its amazing
performance,the Transcend 600x CompactFlash
memory card allows the professional photographers
and enthusiasts to get the most from your digital single
lens reflex (DSLR) camera. Users are guaranteed to
makes consecutive shooting and non-stop video
recording and share their digital artwork with the world!
Placement
Dimensions
Features
•CompactFlash Specification Version 4.1 Complaint
•RoHS compliant products
•Single Power Supply: 3.3V ± 5% or 5V ± 10%
•Operating Temperature: -25
o
C to 85
o
C
•Storage Temperature: -40
o
C to 85
o
C
•Operating/ Storage Humidity: 5% to 95%
•Operation Modes:

PC Card Memory Mode

PC Card IO Mode

True IDE Mode
•True IDE Mode supports:

Ultra DMA Mode 0 to Ultra DMA Mode 6 (Ultra DMA
mode 5/6 must use Power supply: 3.3V)

MultiWord DMA Mode 0 to MultiWord DMA Mode 4

PIO Mode 0 to PIO Mode 6
•PC Card Mode supports up to Ultra DMA Mode 6
•True IDE mode: Fixed Disk (Standard)
•PC Card Mode: Removable Disk (Standard)
•Durability of Connector: 10,000 times
• Built-in 15 bit ECC (Error Correction Code) functionality
•Support Global Wear-Leveling to extend product life
•Compliant to CompactFlash, PC Card Mode, and ATA
standards
Power Consumption
* Maximum value
Product TS8GCF600
TS16GCF600
Standby
2.4mA 2.5mA
Read 222.8mA 232.8mA
Power
Consumption
(DC 3.3V
@
25
℃
)
Write 218.1mA 211.5mA

T
T
TS
S
S8
8
8G
G
G~
~
~1
1
16
6
6G
G
GC
C
CF
F
F6
6
60
0
00
0
0
600X CompactFlash Card
Transcend Information Inc.
V1.0
2
Transcend

T
T
TS
S
S8
8
8G
G
G~
~
~1
1
16
6
6G
G
GC
C
CF
F
F6
6
60
0
00
0
0
600X CompactFlash Card
Transcend Information Inc.
V1.0
3
Block Diagram

T
T
TS
S
S8
8
8G
G
G~
~
~1
1
16
6
6G
G
GC
C
CF
F
F6
6
60
0
00
0
0
600X CompactFlash Card
Transcend Information Inc.
V1.0
4

T
T
TS
S
S8
8
8G
G
G~
~
~1
1
16
6
6G
G
GC
C
CF
F
F6
6
60
0
00
0
0
600X CompactFlash Card
Transcend Information Inc.
V1.0
5
Pin Assignments and Pin Type
PC Card Memory Mode PC Card I/O Mode True IDE Mode 4
Pin
Num
Signal
Name
Pin
Type
In, Out Type
Pin Num
Signal
Name
Pin
Type
In, Out
Type
Pin
Num
Signal
Name
Pin
Type
In, Out
Type
1 GND Ground 1 GND Ground
1 GND Ground
2 D03 I/O I1Z, OZ3 2 D03 I/O I1Z, OZ3
2 D03 I/O I1Z, OZ3
3 D04 I/O I1Z, OZ3 3 D04 I/O I1Z, OZ3
3 D04 I/O I1Z, OZ3
4 D05 I/O I1Z, OZ3 4 D05 I/O I1Z, OZ3
4 D05 I/O I1Z, OZ3
5 D06 I/O I1Z, OZ3 5 D06 I/O I1Z, OZ3
5 D06 I/O I1Z, OZ3
6 D07 I/O I1Z, OZ3 6 D07 I/O I1Z, OZ3
6 D07 I/O I1Z, OZ3
7 -CE1 I I3U 7 -CE1 I I3U 7 -CS0 I I3Z
8 A10 I I1Z 8 A10 I I1Z 8 A10
2
I I1Z
9 -OE I I3U 9 -OE I I3U 9 -ATA SEL
I I3U
10
A09 I I1Z 10 A09 I I1Z 10 A09
2
I I1Z
11
A08 I I1Z 11 A08 I I1Z 11 A08
2
I I1Z
12
A07 I I1Z 12 A07 I I1Z 12 A07
2
I I1Z
13
VCC Power 13 VCC Power
13 VCC Power
14
A06 I I1Z 14 A06 I I1Z 14 A06
2
I I1Z
15
A05 I I1Z 15 A05 I I1Z 15 A05
2
I I1Z
16
A04 I I1Z 16 A04 I I1Z 16 A04
2
I I1Z
17
A03 I I1Z 17 A03 I I1Z 17 A03
2
I I1Z
18
A02 I I1Z 18 A02 I I1Z 18 A02 I I1Z
19
A01 I I1Z 19 A01 I I1Z 19 A01 I I1Z
20
A00 I I1Z 20 A00 I I1Z 20 A00 I I1Z
21
D00 I/O I1Z, OZ3 21 D00 I/O I1Z, OZ3
21 D00 I/O I1Z, OZ3
22
D01 I/O I1Z, OZ3 22 D01 I/O I1Z, OZ3
22 D01 I/O I1Z, OZ3
23
D02 I/O I1Z, OZ3 23 D02 I/O I1Z, OZ3
23 D02 I/O I1Z, OZ3
24
WP O OT3 24 -IOIS16
O OT3 24 -IOCS16
O ON3
25
-CD2 O Ground 25 -CD2 O Ground
25 -CD2 O Ground
26
-CD1 O Ground 26 -CD1 O Ground
26 -CD1 O Ground
27
D11
1
I/O
I1Z, OZ3 27 D11
1
I/O
I1Z, OZ3
27 D11
1
I/O
I1Z, OZ3
28
D121 I/O
I1Z, OZ3 28 D12
1
I/O
I1Z, OZ3
28 D12
1
I/O
I1Z, OZ3
29
D13
1
I/O
I1Z, OZ3 29 D13
1
I/O
I1Z, OZ3
29 D13
1
I/O
I1Z, OZ3
30
D14
1
I/O
I1Z, OZ3 30 D14
1
I/O
I1Z, OZ3
30 D14
1
I/O
I1Z, OZ3
31
D15
1
I/O
I1Z, OZ3 31 D15
1
I/O
I1Z, OZ3
31 D15
1
I/O
I1Z, OZ3
32
-CE2
1
I I3U 32 -CE2
1
I I3U 32 -CS1
1
I I3Z
33
-VS1 O Ground 33 -VS1 O Ground
33 -VS1 O Ground

T
T
TS
S
S8
8
8G
G
G~
~
~1
1
16
6
6G
G
GC
C
CF
F
F6
6
60
0
00
0
0
600X CompactFlash Card
Transcend Information Inc.
V1.0
6
PC Card Memory Mode PC Card I/O Mode True IDE Mode
4
Pin
Num
Signal Name
Pin
Type
In, Out
Type
Pin
Num
Signal Name
Pin
Type
In, Out
Type
Pin
Num
Signal Name
Pin
Type
In, Out
Type
-HIOE
7
HSTROBE
8
34
-HIOE
HSTROBE
10
HDMARDY
11
I I3U 34
-HIOE
HSTROBE
10
-HDMARDY
11
I I3U 34
-HDMARDY
9
I I3Z
-IOWR -IOWR -IOWR
7
35
STOP
10,11
I I3U 35
STOP
10,11
I I3U 35
STOP
8,9
I I3Z
36
-WE I I3U 36 -WE I I3U 36 -WE
3
I I3U
37
READY O OT1 37 -IREQ O OT1 37 INTRQ O OZ1
38
VCC Power
38 VCC Power
38 VCC Power
39
-CSEL
5
I I2Z 39 -CSEL
5
I I2Z 39 -CSEL I I2U
40
-VS2 O OPEN
40 -VS2 O OPEN
40 -VS2 O OPEN
41
RESET I I2Z 41 RESET I I2Z 41 -RESET I I2Z
-WAIT -WAIT IORDY
7
ON1
-DDMARDY
10
-DDMARDY
10
-DDMARDY
8
42
DSTROBE
11
O OT1 42
DSTROBE
11
O OT1 42
DSTROBE
9
O OT1
13
-INPACK -INPACK
43
-DMARQ
12
O OT1 43
-DMARQ
12
O OT1 43 DMARQ O OZ1
-REG I I3U 44 -REG
44
-DMACK
12
DMACK
12
I I3U 44 -DMACK
6
I I3U
45
BVD2 O OT1 45 -SPKR O OT1 45 -DASP I/O I1U, ON1
46
BVD1 O OT1 46 -STSCHG O OT1 46 -PDIAG I/O I1U, ON1
47
D08
1
I/O
I1Z,
OZ3 47 D08
1
I/O
I1Z,
OZ3 47 D08
1
I/O
I1Z, OZ3
48
D09
1
I/O
I1Z,
OZ3 48 D09
1
I/O
I1Z,
OZ3 48 D09
1
I/O
I1Z, OZ3
49
D10
1
I/O
I1Z,
OZ3 49 D10
1
I/O
I1Z,
OZ3 49 D10
1
I/O
I1Z, OZ3
50
GND Ground
50 GND Ground
50 GND Ground
Note: 1) These signals are required only for 16 bit accesses and not required when installed in 8 bit systems. Devices should allow for 3-state
signals not to consume current.
2) The signal should be grounded by the host.
3) The signal should be tied to VCC by the host.
4) The mode is required for CompactFlash Storage Cards.
5) The -CSEL signal is ignored by the card in PC Card modes. However, because it is not pulled upon the card in these modes,
it should not be left floating by the host in PC Card modes. In these modes, the pin should be connected by the host to PC
Card A25 or grounded by the host.
6) If DMA operations are not used, the signal should be held high or tied to VCC by the host. For proper operation in older hosts: while DMA
operations are not active, the card shall ignore this signal,including a floating condition
7) Signal usage in True IDE Mode except when Ultra DMA mode protocol is active.
8) Signal usage in True IDE Mode when Ultra DMA mode protocol DMA Write is active.
9) Signal usage in True IDE Mode when Ultra DMA mode protocol DMA Read is active.
10) Signal usage in PC Card I/O and Memory Mode when Ultra DMA mode protocol DMA Write is active.
11) Signal usage in PC Card I/O and Memory Mode when Ultra DMA mode protocol DMA Read is active.
12) Signal usage in PC Card I/O and Memory Mode when Ultra DMA protocol is active.

T
T
TS
S
S8
8
8G
G
G~
~
~1
1
16
6
6G
G
GC
C
CF
F
F6
6
60
0
00
0
0
600X CompactFlash Card
Transcend Information Inc.
V1.0
7
 Input Leakage Current
Note: In Table 1 below, x refers to the characteristics described in table 2. For example, I1U indicates a pull-up resistor with a type 1
input characteristic.
Table 1: Input Leakage Current
Type Parameter Symbol
Conditions MIN
TYP
MAX
Units
IxZ Input Leakage Current
IL Vih = Vcc / Vil = Gnd
-1
1 µA
IxU Pull-Up Resistor RPU1 Vcc = 5.0V 50k
500k
Ohm
IxD Pull-Down Resistor RPD1 Vcc = 5.0V 50k
500k
Ohm
Note: The minimum pull-up resistor resistance meets the PCMCIA PC Card specification of 10k ohms but is intentionally higher in the
CompactFlash Specification to reduce power use.
 Input Characteristics
Table 2: Input Characteristics
MIN
TYP MAX
MIN
TYP MAX
Type
Parameter Symbol
VCC = 3.3 V VCC = 5.0 V
Units
1 Input Voltage
CMOS
Vih
Vil 2.4
0.6 4.0
1
0.8 Volts
2 Input Voltage
CMOS
Vih
Vil 1.5
0.6 2.0 0.8 Volts
3
Input Voltage
CMOS Schmitt
Trigger
Vth
Vtl
1.8
1.0
2.8
2.0
Volts
Notes: 1) The host provides a logic output high voltage for a CMOS load of .9 x VCC. For a 5 volt product, this translates to .9 x
4.5 = 4.05 volts minimum Voh.
 Output Drive Type
Note: In Table 3 below, x refers to the characteristics described in Table 4. For example, OT3 refers to Totem pole output with a type
3 output drive characteristic.
Table 3: Output Drive Type
Type Output Type Valid Conditions
OTx Totempole Ioh & Iol
OZx Tri-State N-P Channel Ioh & Iol
OPx P-Channel Only Ioh Only
ONx N-Channel Only Iol Only

T
T
TS
S
S8
8
8G
G
G~
~
~1
1
16
6
6G
G
GC
C
CF
F
F6
6
60
0
00
0
0
600X CompactFlash Card
Transcend Information Inc.
V1.0
8
 Output Drive Characteristics
Table 4: Output Drive Characteristics
Type
Parameter Symbol Conditions MIN TYP MAX Units
1 Output Voltage
Voh
Vol
Ioh = -4 mA
Iol = 4 mA
Vcc
-0.8V
Gnd
+0.4V
Volts
2 Output Voltage
Voh
Vol
Ioh = -4 mA
Iol = 4 mA
Vcc
-0.8V
Gnd
+0.4V
Volts
3 Output Voltage
Voh
Vol
Ioh = -4 mA
Iol = 4 mA
Vcc
-0.8V
Gnd
+0.4V
Volts
X Tri-State Leakage
Current Ioz Vol = Gnd Voh = Vcc -10
10 µA

T
T
TS
S
S8
8
8G
G
G~
~
~1
1
16
6
6G
G
GC
C
CF
F
F6
6
60
0
00
0
0
600X CompactFlash Card
Transcend Information Inc.
V1.0
9
Signal Description
Signal Name Dir.
Pin Description
A10 – A00
(PC Card Memory Mode)
A10 – A00
(PC Card I/O Mode)
A02 - A00
(True IDE Mode)
I
I
8,10,11,12,
14,15,16,17,
18,19,20
18,19,20
These address lines along with the -REG signal are used to
select the following:
The I/O port address registers within the CompactFlash Storage Card , the
memory mapped port address registers within the CompactFlash Storage Card,
a byte in the card's information structure and its
configuration control and status
registers.
This signal is the same as the PC Card Memory Mode signal.
In True IDE Mode, only A[02:00] are used to select the one of eight registers
in the Task File, the remaining address lines should be grounded by the
host.
BVD1
(PC Card Memory Mode)
-STSCHG
(PC Card I/O Mode)
Status Changed
-PDIAG
(True IDE Mode)
I/O
46 This signal is asserted high, as BVD1 is not supported.
This signal is asserted low to alert the host to changes in the
READY and Write
Protect states, while the I/O interface is configured. Its use is controlled by the
Card Config and Status Register.
In the True IDE Mode, this input / output is the Pass Diagnostic signal in the
Master / Slave handshake protocol.
BVD2
(PC Card Memory Mode)
-SPKR
(PC Card I/O Mode)
-DASP
(True IDE Mode)
I/O
45 This signal is asserted high, as BVD2 is not supported.
This line is the Binary Audio output from the card. If the Card does not support
the Binary Audio function, this line should be held negated.
In the True IDE Mode, this input/output is the Disk Active/Slave
Present signal in
the Master/Slave handshake protocol.
-CD1, -CD2
(PC Card Memory Mode)
-CD1, -CD2
(PC Card I/O Mode)
-CD1, -CD2
(True IDE Mode)
O
26,25 These Card Detect pins are connected to ground on the
CompactFlash Storage
Card. They are used by the host to determine that the CompactFlash Storage
Card is fully inserted into its socket.
This signal is the same for all modes.
This signal is the same for all modes.

T
T
TS
S
S8
8
8G
G
G~
~
~1
1
16
6
6G
G
GC
C
CF
F
F6
6
60
0
00
0
0
600X CompactFlash Card
Transcend Information Inc.
V1.0
10
Signal Name Dir.
Pin Description
-CE1, -CE2
(PC Card Memory Mode)
Card Enable
-CE1, -CE2
(PC Card I/O Mode)
Card Enable
-CS0, -CS1
(True IDE Mode)
I
7,32 These input signals are used both to select the card and to indi
cate to the card
whether a byte or a word operation is being performed. -CE2 always accesses
the odd byte of the word.-CE1 accesses the even byte or the Odd byte of the
word depending on A0 and -CE2. A multiplexing scheme based on A0,-CE1,
-CE2 allows 8 bit hosts to access all data on D0-D7. See Table 27, Table 29,
Table 31, Table 35, Table 36 and Table 37.
This signal is the same as the PC Card Memory Mode signal.
In the True IDE Mode, -CS0 is the address range select for the task file
registers while -CS1 is used to select the Alternate Status Register and the
Device Control Register.
While –DMACK is asserted, -CS0 and –CS1 shall be held negated and the
width of the transfers shall be 16 bits.
-CSEL
(PC Card Memory Mode)
-CSEL
(PC Card I/O Mode)
-CSEL
(True IDE Mode)
I
39 This signal is not used for this mode, but should be connected by
the host to PC
Card A25 or grounded by the host.
This signal is not used for this mode, but should be connected by
the host to PC
Card A25 or grounded by the host.
This internally pulled up signal is used to configure this device as
a Master or a
Slave when configured in the True IDE Mode.
When this pin is grounded, this device is configured as a Master.
When the pin is open, this device is configured as a Slave.
D15 - D00
(PC Card Memory Mode)
D15 - D00
(PC Card I/O Mode)
D15 - D00
(True IDE Mode)
I/O
31,30,29,28,
27,49,48,47,
6,5,4,3,2,
23, 22, 21
These lines carry the Data, Commands and Status information
between the host
and the controller. D00 is the LSB of the Even
Byte of the Word. D08 is the LSB
of the Odd Byte of the Word.
This signal is the same as the PC Card Memory Mode signal.
In True IDE Mode, all Task File operations occur in byte mode
on the low order
bus D[7:0] while all data transfers are 16 bit using D[15:0].
GND
(PC Card Memory Mode)
GND
(PC Card I/O Mode)
GND
(True IDE Mode)
--
1,50 Ground.
This signal is the same for all modes.
This signal is the same for all modes.