Transmitter Solutions RCMMOD User manual

NO TOUCH ADA ACCESS
RETROFIT MODULE
Retrofit Contactless Module (RCM)
RCMMOD
Two Wire Module (TWM)
TWMMOD
PH 866.975.0101 • FX 866.975.0404
www.transmittersolutions.com

Package
• Retrofit Contactlesss Module - 1
• Two Wire Module - 1
• Expansion Screws 4*20mm - 4
• Screw M3*20mm - 4
• Double Sided Adhesive 43x31x1mm - 2
• Acetate Cloth Tape 55x40x0.15mm - 1
• Installation and Operation Manual - 1
1
Specifications
Retrofit Contactless Module
Operating Voltage DC 10-24V
Operating Current 200mA@12VDC (max)
Operating Temperature -14°F - 140°F
Trigger Range 2 in. - 4 in.
Relay Output Dry Contact, 30VDC with 1A (max)
Dimensions L 2.36 in. x W 1.77 in. x H .79 in.
Two Wire Module
Operating Voltage DC 10-24V
Operating Current 200mA@12VDC (max)
Operating Temperature -14°F - 140°F
Communication Range < 7.87 in.
Relay Output Dry Contact, 30VDC with 1A (max)
Dimensions L 2.56 in. x W 2.01 in. x H .75 in.

Installation
• Wiring all wires to the correct place.
• Fix the screws as shown in figure 1.
• Wiring the wires to the mechanical switch as shown in figure 2.
• Attach the antenna to the metal plate as shown in figure 3.
• Attach the acetate cloth tape to the back of the antenna as shown in figure 4.
2
Figure 2
Figure 4
Figure 1
Figure 3

1
GRAY
MS_NO
Mechanical Switch - Normal Open
2
YELLOW
MS_COM
Mechanical Switch - Common
3
BLUE
MS_NC
Mechanical Switch - Normal Close
JP4 Wiring
3
GREEN
LA
Communicaon Bus - LA
4
WHITE
LB
Communicaon Bus - LB
JP2 Wiring
1
RED
+12/24V
Power Supply
2
BLACK
GND
Ground
3
BLACK
GND
Ground
4
BROWN
RELAY_NO
Relay Output - Normal Open
5
ORANGE
RELAY_COM
Relay Output - Common
6
PURPLE
RELAY_NC
Relay Output - Normal Close
JP1 Wiring
JP1
Connect to door controller
JP2
Connect to TWM(Master)
JP3
Antenna
JP4
Connect to Mechanical Switch
Connector Definition
Retrofit Contactless Module
3

3
GREEN
LA
Communicaon Bus - LA
4
WHITE
LB
Communicaon Bus - LB
JP6 Wiring
1
RED
+12/24V
Power Supply
2
BLACK
GND
Ground
3
BLACK
GND
Ground
4
BROWN
RELAY_NO
Relay Output - Normal Open
5
ORANGE
RELAY_COM
Relay Output - Common
6
PURPLE
RELAY_NC
Relay Output - Normal Close
JP5 Wiring
JP5
Connect to door controller
JP6
Connect to TWM(Slave) embedded in RCM
Connector Definition
Two Wire Module
4

Wiring Diagrams
5
+VDC
GND
REL_COM
REL_NO/NC
Door Controller
Normal Mode:
Retrofit Contactless Module LED Indicators:
• Retrofit Contactless Module directly connects to door controller.
• Put your hand near the button then you will trigger the device. The relay
inside the device will trigger for 1 second, and the buzzer will beep once.
• Support mechanical override.
• Enable and disable buzzer. Trigger the device 3 times in 10 seconds, and the
4th time keep your hand near the button (sensing range), until a long beep to
complete. If the buzzer is enabled before the operation, it will no longer beep,
and vice versa.
• LED1 (Green LED) on: The relay is triggered
• LED2 (Red LED) on: The device powers on
• LED2 (Red LED) off: Inductive sensor is activated
• LED3 (Red LED) flash: Two Wire modules
communicate normally
LED3
LED2
LED1

6
Wiring Diagrams
Normal Mode:
Two Wire Module LED Indicators:
• Retrofit Contactless Module works with Two Wire Modules. Only two wires
are needed for both power supply and data communication.
• Put your hand near the button then you will trigger the device, and the buzzer
will beep once. TWM (Slave) embedded in the RCM will send the signal to the
TWN (Master). The relay inside the TWN (Master) will trigger for 1 second.
• Support mechanical override.
• Enable and disable buzzer. Trigger the device 3 times in 10 seconds, and the
4th time keep your hand near the button (sensing range), until a long beep to
complete. If the buzzer is enabled before the operation, it will no longer beep,
and vice versa.
• LED5 (Green LED) on: The relay is triggered
• LED4 (Red LED) flash: Two Wire modules
communicate normally
+VDC
LA
LB
GND
REL_COM
REL_NO/NC
Door Controller
LED5
LED4

PH 866.975.0101 • FX 866.975.0404
www.transmittersolutions.com